Thingiverse
Gates Idler mounts for Rostock Max by tajd3
by Thingiverse
Last crawled date: 2 years, 11 months ago
I have a Rostock Max v2, but I think this should work for all versions with motors in the base, though I have not verified this. Check all dimensions of your model before you start this upgrade.
I was getting some vertical banding (NOT ringing) on my prints and decided to replace my belts and stock idlers with authentic Gates parts. Plus my original belts were getting pretty worn.
Because the Gates idlers are much smaller (12mm vs 22mm diameter) than the 608zz bearings used as the original idlers, new brackets are needed to maintain the proper belt alignment. These brackets improve the belt alignment over stock. On the outside, the belt path is within the extrusion V-track and on the inside the belt path is completely outside the extrusion V-track. The belt path with the stock idlers was right at the mouth of the inner and outer V-tracks which allowed the belt to rub on the ends of the extrusion causing friction and belt wear.
This design reuses all the original fasteners and holes in the tower supports.
The following hardware (in addition to the existing) is required for the base:
6 of 5mm X 20mm stainless shelf pins
12 of 5mm ID X 6mm OD X 0.4mm shims
12 of M5 washers
3 of Gates GT2 20T idlers
3 of Gates GT2 smooth idlers
3 of Gates GT2 16T pulleys (optional - gives an increase in resolution from 80steps/mm to 100steps/mm)
3 of M4 x 45mm screw with lock nuts and washers (12 washers total)
The following hardware (in addition to the existing) is required for the top:
9 of 5mm X 20mm pins
12 of 5mm ID X 6mm OD X 0.4mm shims
12 of M5 washers
6 of Gates GT2 20T idlers
6 of 625zz bearings (optional - a printed part will work as well)
3 of M4 x 45mm screw with lock nuts and 4 washers each (axle for bearings above)
6 of M3 x 8mm screws (to adjust the position of bearing axle)
--- Still working on description ---
I was getting some vertical banding (NOT ringing) on my prints and decided to replace my belts and stock idlers with authentic Gates parts. Plus my original belts were getting pretty worn.
Because the Gates idlers are much smaller (12mm vs 22mm diameter) than the 608zz bearings used as the original idlers, new brackets are needed to maintain the proper belt alignment. These brackets improve the belt alignment over stock. On the outside, the belt path is within the extrusion V-track and on the inside the belt path is completely outside the extrusion V-track. The belt path with the stock idlers was right at the mouth of the inner and outer V-tracks which allowed the belt to rub on the ends of the extrusion causing friction and belt wear.
This design reuses all the original fasteners and holes in the tower supports.
The following hardware (in addition to the existing) is required for the base:
6 of 5mm X 20mm stainless shelf pins
12 of 5mm ID X 6mm OD X 0.4mm shims
12 of M5 washers
3 of Gates GT2 20T idlers
3 of Gates GT2 smooth idlers
3 of Gates GT2 16T pulleys (optional - gives an increase in resolution from 80steps/mm to 100steps/mm)
3 of M4 x 45mm screw with lock nuts and washers (12 washers total)
The following hardware (in addition to the existing) is required for the top:
9 of 5mm X 20mm pins
12 of 5mm ID X 6mm OD X 0.4mm shims
12 of M5 washers
6 of Gates GT2 20T idlers
6 of 625zz bearings (optional - a printed part will work as well)
3 of M4 x 45mm screw with lock nuts and 4 washers each (axle for bearings above)
6 of M3 x 8mm screws (to adjust the position of bearing axle)
--- Still working on description ---
Similar models
thingiverse
free
GT2 20T pulley for GEEETech I3 ProB by ybjack
...r geeetech i3 prob by ybjack
thingiverse
idler wheel for x,y driving belt.
please insert into it the bearing of the stock parts.
thingiverse
free
Belt driven Z pulley mount w/ GT2 6mm belt 5mm bore 20t idler by Evilkoal
...e idler mount to fit the idlers i have.
gt2 20t 6mm belt, 5mm bore idler.
printed with 50% "archimedian chords" infill.
thingiverse
free
Hictop 3dp11 Adjustable Y Idler Mount 2.0 by SaberShip
...ler pulley for 6mm wide gt2 belt
1x m5 x30 bolt
1x m5 nylon lock insert nut (regular m5 nut may work)
2x m3 x10 screws
2x m3 nuts
thingiverse
free
FT-5 Z screw alignment by Randomloser
...ews(at least 45mm) and nuts.
the orientation of the middle part could be a problem, so it might be better to place it in reverse.
thingiverse
free
TRONXY X5S - Z motor sync by WT1704
...e platform on the stepper and 3 * m5 screws and nuts for the pulley
1 * m3 screw and nut to hold the tension stick with the block
thingiverse
free
Prusa MK3 Bear 20T 5ID Gates Y idler + tensioner
... on the insertion depth: rely exclusively on the belt to verify the alignment.
again, with great thanks to gregsaun for his work.
thingiverse
free
GT2 pulley 20T 3mm and 5mm bore by whitefoot
...
this pulley for gt2 belt. it is replacing two f623zz bearings and helps to turn the belt, wherever you want. two bore 3 and 5mm.
thingiverse
free
Y-belt holder and tensioner for MK3/S - Gates 20T Idler by BMac1203
... frame, but that part didn't line-up with the stock mk3s part.
tested on my printer - this works with gates 20t idler pulley.
grabcad
free
Pulley GT2 - 20T B5
... 2 m4x4 grub screws.
created by dzino
gt2 - 20t napínacia ozubená kladka s ložiskom pre ozubené remene 2gt - 6mm. pre 5mm osku.
thingiverse
free
Hictop 3dp11 Adjustable Y Idler Mount by SaberShip
...rts:
x1 stock 608zz idler bearing
x1 stock m3 bolt and nut
x2 stock m5 bolts
x2 stock m5 t-slot nuts
x2 m3 x 10 screws
x2 m3 nuts
Rostock
thingiverse
free
Endstop for Rostock by Raz0neR
...endstop for rostock by raz0ner
thingiverse
endstop for rostock.
thingiverse
free
Rostock Cooling by nobicore
...rostock cooling by nobicore
thingiverse
rostock cooling
thingiverse
free
ROSTOCK PARTS by OC3D
...rostock parts by oc3d
thingiverse
parts for our modified rostock extruder assembly
thingiverse
free
Rostock squirrel fan by MarioPanic
...rostock squirrel fan by mariopanic
thingiverse
rostock squirrel fan
thingiverse
free
FC Hansa Rostock by ron86
...fc hansa rostock by ron86
thingiverse
fc hans rostock logo
thingiverse
free
rostock mini carriage by cjol
...rostock mini carriage by cjol
thingiverse
carriage for my rostock mini project
thingiverse
free
Rostock and Rostock Mini Dual Extruder Mount by westonshakespear
...ht.
sorry about the pictures, my filament jammed for part of the print and i am waiting for a new part to print a better version.
thingiverse
free
Rostock mini clip by Scott_Chen
...rostock mini clip by scott_chen
thingiverse
rostock mini clip for printer base glass
thingiverse
free
Rostock Board holder by drewan
...rostock board holder by drewan
thingiverse
this is a clip for using a rostock board as a print surface.
thingiverse
free
Rostock Fan Bracket by ImprisonedByTime
...rostock fan bracket by imprisonedbytime
thingiverse
this bracket is for a 40mm fan to attach to the rostock 3d printer
Idler
3d_export
$20
telescopic stacker belt conveyor
...and the actual components are as follows cema c idler cema c impact roller dodge bearing avoid tension bearing...
3d_export
$49
Liebherr R9250 Tracks - Crawler
...main parts: bottom rollers car bodies final drives top idler front idlers slewing rings-turntable bearings sprockets text track chains...
3d_export
$119
JD - 953MH Tracked Log Loader
...boby with engine<br>main body bolts<br>main body grilles<br>pedals<br>right - front idlerlt;br>right - rear idler<br>right track chain<br>right track links<br>right track protector<br>right...
3d_export
$129
JD - 959MH Tracked Feller Buncher
...boby with engine<br>main body bolts<br>main body grilles<br>pedals<br>right - front idlerlt;br>right - rear idler<br>right track chain<br>right track links<br>right track protector<br>right...
3d_export
$119
JD - 959MH Tracked Log Loader
...boby with engine<br>main body bolts<br>main body grilles<br>pedals<br>right - front idlerlt;br>right - rear idler<br>right track chain<br>right track links<br>right track protector<br>right...
3d_export
$119
JD - 953MH Tracked Harvester
...tool - lower<br>moving limbing tool - upper<br>pedals<br>right - front idlerlt;br>right - rear idler<br>right feed rollers<br>right track chain<br>right track links<br>right...
thingiverse
free
Idler seat by jcen517
...idler seat by jcen517
thingiverse
idler seat
thingiverse
free
Idler by GEON_3D
...idler by geon_3d
thingiverse
idler para extrusor 1,75
imprimir en abs, petg o cualquier material resistente
thingiverse
free
wade idler by nautilux
...wade idler by nautilux
thingiverse
wade idler reforzado
thingiverse
free
Idler Frame by Dinusha
...idler frame by dinusha
thingiverse
idler frame specially for the belt conveyors.
Gates
archibase_planet
free
Gate
...gate archibase planet gate gates garage gate gate 1 - 3d model (*.gsm+*.3ds) for...
archibase_planet
free
Gate
...gate archibase planet gate garage gate gates gate 2 - 3d model (*.gsm+*.3ds) for exterior 3d...
archibase_planet
free
Gate
...gate archibase planet gate garage gate gates gate garage n050214 - 3d model (*.gsm+*.3ds) for interior...
archibase_planet
free
Gates
...gates
archibase planet
gates gate
gates - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Gate
...gate archibase planet gate gates barrier gate - 3d model (*.gsm+*.3ds) for exterior 3d...
archibase_planet
free
Gate
...gate archibase planet gate gates barrier gate n210114 - 3d model (*.3ds) for exterior...
archibase_planet
free
Gate
...gate archibase planet gate gates barrier gate n180914 - 3d model (*.gsm+*.3ds) for exterior...
archibase_planet
free
Gate
...gate archibase planet gate gates fence gate n050814 - 3d model (*.gsm+*.3ds) for exterior...
archibase_planet
free
Gates
...gates
archibase planet
gate gates fencing
gates n120708 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Gates
...gates
archibase planet
gate gates fencing
gates n140708 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
Mounts
3d_export
free
mounting bracket
...the part of a hinge, handle or latch that mounts the hardware to a cabinet. mounting plates make it...
turbosquid
$2
MOUNTING
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mounts
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mount Fuji
...fuji
turbosquid
free 3d model mount fuji for download as obj on turbosquid: 3d models for games, architecture, videos. (1579977)
3d_export
$5
Headphone mount LR
...headphone mount lr
3dexport
headphone mount l+r
turbosquid
$39
Mount rainier
...quid
royalty free 3d model mount rainier for download as fbx on turbosquid: 3d models for games, architecture, videos. (1492586)
turbosquid
$5
pipe mounting
...quid
royalty free 3d model pipe mounting for download as obj on turbosquid: 3d models for games, architecture, videos. (1293744)
turbosquid
$3
Mounting Tires
...uid
royalty free 3d model mounting tires for download as fbx on turbosquid: 3d models for games, architecture, videos. (1708511)
3d_export
$5
Magnetic GoPro Mount
...pro mount
3dexport
cool magnetic mount for gopro. allows you to mount the camera on flat metal surfaces and get exclusive shots.
turbosquid
$5
Stone Mount
...ty free 3d model stone mount for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1370306)