Thingiverse
Garmin 910XT 22mm Aerobar Extension Mount by slonold
by Thingiverse
Last crawled date: 3 years ago
Overview
Simple system with adjustable viewing angle to mount a Garmin 910XT via the standard wrist strap to 22mm diameter aerobar extensions. Accommodates inner bar spacing of 40 to 50mm as well as shifter cables running on the inner face of the aerobars.
Tools and Materials Required
3mm x 3 to 6mm long or #3-48 x 1/8 to 1/4" long set screws for angle adjustment X2
1.5mm(for m3) or 0.050"( for #3-48) hex key for set screws
2.4mm or 3/32" (for m3) or 5/16" (for #3-48) drill bit to size set screw holes
m3 x 0.5 or #3-48 tap
Miniature Cable Ties (100mm/4" x 2.4mm/3/32" x 1mm/0.04") X4
Half round file ~12mm/1/2" and sharp knife for clean-up.
Printing
Print 2 of Garmin_Mount_Pin - recommend individually for best diameter consistency
Print 1 of either Garmin_Mount_Centre_Front_Adjust (pictured) or Rear_Adjust
Material: PETG recommended
Shell Thickness: 1.5 to 2mm
Infill: 10-15% should be plenty
Support: Not required if layer height is small. i used variable layer height from 0.32mm on the bottom of the pins to 0.16mm for the section with the cable tie passage (Slic3r) with a 0.5mm nozzle.
Assembly:
Size the angle adjustment holes and tap threads - remember PETG likes it slow, cool and needs frequent chip clean out in order to avoid rewarding you with a gummy mess. Note that you will likely have to bury the tap in order to get threads through to the bore of the centre piece but bear in mind that a snapped off tap in the work piece is a sad sight indeed.
Clean up the bore of the centre piece and outside of the centre pins ensuring pins fit freely but not loosely in centre piece and that the cable tie passages are reasonably clear..
Install a cable tie in each pin (a little judicious curving of the cable tie will help).
Push both pins fully into the centre piece.
Locate between extensions - note that oblong hole in centre piece faces up.
Add second cable ties and tighten firmly.
Mount watch - note that strap does not have to be tight - spare your spring pins
Adjust angle and fix by gently snugging set screws.
Simple system with adjustable viewing angle to mount a Garmin 910XT via the standard wrist strap to 22mm diameter aerobar extensions. Accommodates inner bar spacing of 40 to 50mm as well as shifter cables running on the inner face of the aerobars.
Tools and Materials Required
3mm x 3 to 6mm long or #3-48 x 1/8 to 1/4" long set screws for angle adjustment X2
1.5mm(for m3) or 0.050"( for #3-48) hex key for set screws
2.4mm or 3/32" (for m3) or 5/16" (for #3-48) drill bit to size set screw holes
m3 x 0.5 or #3-48 tap
Miniature Cable Ties (100mm/4" x 2.4mm/3/32" x 1mm/0.04") X4
Half round file ~12mm/1/2" and sharp knife for clean-up.
Printing
Print 2 of Garmin_Mount_Pin - recommend individually for best diameter consistency
Print 1 of either Garmin_Mount_Centre_Front_Adjust (pictured) or Rear_Adjust
Material: PETG recommended
Shell Thickness: 1.5 to 2mm
Infill: 10-15% should be plenty
Support: Not required if layer height is small. i used variable layer height from 0.32mm on the bottom of the pins to 0.16mm for the section with the cable tie passage (Slic3r) with a 0.5mm nozzle.
Assembly:
Size the angle adjustment holes and tap threads - remember PETG likes it slow, cool and needs frequent chip clean out in order to avoid rewarding you with a gummy mess. Note that you will likely have to bury the tap in order to get threads through to the bore of the centre piece but bear in mind that a snapped off tap in the work piece is a sad sight indeed.
Clean up the bore of the centre piece and outside of the centre pins ensuring pins fit freely but not loosely in centre piece and that the cable tie passages are reasonably clear..
Install a cable tie in each pin (a little judicious curving of the cable tie will help).
Push both pins fully into the centre piece.
Locate between extensions - note that oblong hole in centre piece faces up.
Add second cable ties and tighten firmly.
Mount watch - note that strap does not have to be tight - spare your spring pins
Adjust angle and fix by gently snugging set screws.
Similar models
thingiverse
free
Aerobar Mount by OdoSpace
.... the bar diameter is 22mm (may fit on others too).
to mount your garmin use the original garmin edge mount (see provided image).
thingiverse
free
Gopro (Garmin Virb) extension - adjustable angle
...gopro (garmin virb) extension - adjustable angle
thingiverse
adjustable extension mount for gopro and garmin virb
thingiverse
free
Pi 3 Home Assistant top, zip/cable tie bottom by bduhan
...rt for logo
no gpio or ribbon cable holes
bottom
cable/zip tie mounting holes along one side.
m3 machine screws secure pi and top
thingiverse
free
Garmin Forerunner 910xt Bicycle Mount by ohecker
...garmin forerunner 910xt bicycle mount by ohecker
thingiverse
mounts a garmin 910xt sportswatch to the stem of a bicycle.
thingiverse
free
Phone holder by Fredric
... the two holes to be tapped for m3 screws with 2.5 mm drill.
the other holes are drilled 3mm.
glue rubber on the bottom for grip.
thingiverse
free
Wyze Cam Mount Extension for Ender 3 by rothvin
...note: the wyze cam mount extension sits on the wyze cam mount which is available here: https://www.thingiverse.com/thing:3513349.
thingiverse
free
2020 Extrusion Cable Tie Mounts by JMadison
...hese are designed for cable ties less than 3mm wide.
the hole is for m3 flathead screws.
these should be printed without support.
thingiverse
free
Garmin Mount for Profile design T2 Aerobar by vishnujs
... to customize: http://a360.co/2bi83w4
disclaimer:
i have not tested the strength of this extensively, use it at your own risk :-)
thingiverse
free
Clip holder by bezelt
...ned this cable tie holder to hold the cable ties in place on my boat. one slit for the cable tie, and one hole for a screw / nut.
thingiverse
free
Ender 3 Pro X Axis Cover with Adjustable Endstop and Cable Tie Points by DJScopeSOFM
...er with multiple locating holes for the endstop and points for cable ties.
3d dwg attached so that you can modify it as you wish.
910Xt
thingiverse
free
Garmin Forerunner 910xt Bicycle Mount by ohecker
...garmin forerunner 910xt bicycle mount by ohecker
thingiverse
mounts a garmin 910xt sportswatch to the stem of a bicycle.
thingiverse
free
Garmin 910XT bracelet / wristband by Jonathanmf
...the short garmin 910xt wristband part.
need to be print with flexible filament, of course :)
fit perfectly.
have fun.
jonathan
thingiverse
free
Garmin 910XT charging clip repair by tommo27
...ginal clip is curved on all surfaces, my version is obviously flat on the back face for printing purposes but it works just fine.
thingiverse
free
Bike Watch mount Bike Handle Bar Mount 31.8mm Watch mount by PSomeone
...mount 31.8mm watch mount by psomeone thingiverse garmin™ forerunner 910xt but many other watches will fit. it's a simple...
Slonold
thingiverse
free
Crabby Cap Zesty Nimble SeeMeCNC HE280/Accelerometer Mount by slonold
... the ptfe tube should contact the bottom of the filament guide on centre without distortion. re-trim the ptfe tube if necessary.
thingiverse
free
Nimble Gimbal - Gimbaling Extruder Motor Mount for Zesty Nimble by slonold
...?). with the x60 i went with a 0.3mm nozzle and 0.2mm extrusion width, 3 perimeters, 0.125 layer height and 5 top/bottom layers.
thingiverse
free
Prometheus Mount for SeeMeCNC Rostock Ball Joint Platform +/- Accelerometer Option by slonold
...ive to the clamp plate like a clam shell.
be sure to seat bowden tube and insert ptc retainer before mounting accelerometer board
thingiverse
free
PanelDue 5" and Duet 2 Mounts for SeeMeCNC Rostock Max V2 by slonold
...phery of the onyx bed. some tape to hold the bed and template down will be your friend whilst you outline the bed plate cut out.
thingiverse
free
Belt Tension Adjust Truck for SeeMeCNC Ball Joint System and 1"x1" Extrusion by slonold
...ion truck at top, check tension at middle against fixed distance reference. tension at will!! gently snug screws when finished.
thingiverse
free
Nimble Gimbal For 2020 Delta Frame by quadcells
...i saw slonold's nimble gimbal and liked the idea. slonold did a great job on his design. i needed...
thingiverse
free
Nimble Gnu - System to Adapt the Zesty Nimble Extruder to a Prometheus V2 Hotend Mounted to a SeeMeCNC Balljoint Effector Platform with Accelerometer Probe PCB by slonold
...ter, strap down the whip.
remember to revisit your slicer retraction settings. it is a whole new world without the bowden tube.
thingiverse
free
Zesty Nimble V2 Breech Replica by kulfuerst
...p3 - bearing offset by 0.3 mm i like slonold#39;s naming system and adapted it here. i have not...
Aerobar
thingiverse
free
Barfly shim for aerobars by Enviro
...barfly shim for aerobars by enviro
thingiverse
a shim to mount a barfly accessory mount on standard aerobars.
thingiverse
free
Aerobar bracket riser by Mark_S
...ight of forward-projecting aerobars.
there are two sizes: 15 and 30 mm, which may be used in combination to give a rise of 45 mm.
thingiverse
free
aerobar phone/lamp holder by electronicstime
...erobars to mount my phoneholder. it fits on the btwin aerobar, but will work on others depending on the distance between the bars
thingiverse
free
Aerobars Headlamp/GoPro mount by Roxanna77
... roxanna77
thingiverse
this is a little bar for mounting a headlight or a gopro onto an set of profile designs century aerobars.
thingiverse
free
Garmin mount for aerobars by alga42
...diameter, print, clean up the mount area with a knife or sandpaper to damage the garmin as little as possible, clip on and enjoy.
thingiverse
free
Spinningbike Kettler Racer Aerobar-accessories by demjansein
...giverse
replacement for the broken parts of the aerobar-armrests of an older kettler racer spinning-bike (with a 22mm handlebar)
thingiverse
free
Aerobar Mount by OdoSpace
.... the bar diameter is 22mm (may fit on others too).
to mount your garmin use the original garmin edge mount (see provided image).
thingiverse
free
Bike aerobar BTA bottle cage mount by Mape
... most bta mounts don't work.
the plate should be attached to aerobar extension with 4 small zip ties or something equivalent.
thingiverse
free
Aerobar 50mm Riser with Di1 by JoeSay
...aerobar 50mm riser with di1 by joesay
thingiverse
50mm riser with di2 mount
thingiverse
free
Profile T1+ aerobar 40mm spacer by mathesonmd
... save your back. you'll need a pair of m6x55mm bolts for each spacer. profile charge $25 for these little pieces of plastic.
Garmin
thingiverse
free
Garmin Mount
...garmin mount
thingiverse
garmin replacement mount
thingiverse
free
Garmin Adapter for GoPro
...garmin adapter for gopro
thingiverse
garmin adapter for gopro
thingiverse
free
garmin vivofit by cerezorg
...garmin vivofit by cerezorg
thingiverse
garmin vivofit strap
thingiverse
free
Garmin Baseplate
...ension large enough for a single track bolt with a small knob. attach garmin mount to base plate using three sheet metal screws.
thingiverse
free
Support Garmin SEAT
...support garmin seat
thingiverse
support garmin seat 10r-04 6953
www.vespa-riviera.ch
thingiverse
free
Garmin Sun Screen
...garmin sun screen
thingiverse
this is a sun screen for my garmin to make it better visible in direct sunlight.
thingiverse
free
Garmin Suspension holster by JorpedNOR
...garmin suspension holster by jorpednor
thingiverse
holster for the garmin suspension
thingiverse
free
Garmin stem mount by Mister_sovereign
...garmin stem mount by mister_sovereign
thingiverse
garmin stem mount
thingiverse
free
Garmin Bracket by trio0815
...garmin bracket by trio0815
thingiverse
garmin gps navi bracket universal in different version
the new one for gopro systems
thingiverse
free
soporte Garmin 500 by llelle
...soporte garmin 500 by llelle
thingiverse
mount for garmin 500 gps
22Mm
thingiverse
free
22mm Hook by UncleDa
...22mm hook by uncleda
thingiverse
22mm hook
thingiverse
free
Uhrenarmband 22mm by GHennrich
...uhrenarmband 22mm by ghennrich
thingiverse
uhrenarmband 22mm
thingiverse
free
Fidget Spinner 22mm
...fidget spinner 22mm
thingiverse
22mm fidget spinner
thingiverse
free
Stangenhalter 22mm Rohr
...stangenhalter 22mm rohr
thingiverse
stangenhalter 22mm rohr
thingiverse
free
Propellerschlüssel 22mm by reini0077
...propellerschlüssel 22mm by reini0077
thingiverse
propellerschlüssel yamaha 22mm.
thingiverse
free
22mm wrench by joraasen
...22mm wrench by joraasen
thingiverse
wrench for 22mm vaporizer tanks.
thingiverse
free
22mm Tool by kgarrison1
...22mm tool by kgarrison1
thingiverse
22mm tool design created for class.
thingiverse
free
RAIL 22mm by Zyx_Q
...rail 22mm by zyx_q
thingiverse
7 teeth ris rail for 22mm mounts.
thingiverse
free
Cap Nut 22mm.
...cap nut 22mm.
thingiverse
tap nut 22 mm.
tapon ciego 22mm.
thingiverse
free
22mm Motor mount tarot style 22mm booms by Dim3nsion
...22mm boom motor mount, slots on 22mm cf booms, holes there for plates, will upload dxf and stl files for the plate at some point.
Extension
thingiverse
free
Tail extension
...tail extension
thingiverse
this is a tail extension for binary.
thingiverse
free
Clip extension by dgw277
...clip extension by dgw277
thingiverse
clip extension
thingiverse
free
Extension leads 48mm
...extension leads 48mm
thingiverse
extension leads 48mm
thingiverse
free
GoPro Extension by mbremer
...gopro extension by mbremer
thingiverse
gopro extension mount
thingiverse
free
Extension Cord Extension by DraftingJake
...t a further reach. only takes about an hour to print. also when not in use this would be able to protect the prongs on your cord.
thingiverse
free
extension for vacuum by texano
...extension for vacuum by texano
thingiverse
extension for vacuum cleaners for small areas such as car
thingiverse
free
Ratchet extension organizer
...rse
this is just a simple extension holder and organizer works best with 1/2 and 3/8 in extensions but will hold 1/4 in as well.
thingiverse
free
Dji F450 leg extension extension by Mackelday
...ension http://www.thingiverse.com/thing:833924
it's the exact same but i extended the bottom a bit to accomodate my gimbal.
thingiverse
free
Gopro Extension by Datheus
...sion gopro :)https://www.youtube.com/watch?v=vfsx25r7owo
blind nut m5.
https://www.facebook.com/pages/datheus/289941987825883
thingiverse
free
Throttle Lever Extension
...throttle lever extension
thingiverse
throttle lever extension for saito fa-40
https://youtu.be/bnjgwzeo5ty
Mount
thingiverse
free
Pen Mount on BLTouch mount by jetspot
...pen mount on bltouch mount by jetspot
thingiverse
pen mount on bltouch mount
thingiverse
free
RAM Mount, Mount by seanmclean
...ram mount, mount by seanmclean
thingiverse
bridging plate to attach ram mount to yamaha 242, for chartplotter placement.
thingiverse
free
Mount for mount for Garmin GPS by GNOBLIN
...you can use this mount for prevent rotation simple mount around hendelbars.
d handelbar 31.8mm
use m3 screw and din 16903 plug.
thingiverse
free
Permanent mount for Modular Mounting System by WIR14
...permanent mount for modular mounting system by wir14
thingiverse
permanent mount for modular mounting system.
thingiverse
free
Gopro Mount and antenna mount by SuperYoyo
...gopro mount and antenna mount by superyoyo
thingiverse
cut the carbon platform to pass the gopro mount and enjoy !
thingiverse
free
Hexagon Mount for 50mm Mount (Sparkcube) by Draman
...for 50mm mount (sparkcube) by draman
thingiverse
hexagon mount remix from skimmys hotend-mount for sparkcube or other 50mm-mount
thingiverse
free
mount by gixster
...mount by gixster
thingiverse
custom mount
thingiverse
free
Mount by Matrxi999
...mount by matrxi999
thingiverse
shelf mount
thingiverse
free
Motor mount
...motor mount
thingiverse
motor mount
thingiverse
free
GoPro Mount
...gopro mount
thingiverse
gopro mount