Thingiverse
Food dehydrator silica desiccant tray by derekcgs
by Thingiverse
Last crawled date: 3 years, 4 months ago
A tray to hold silica gel desiccants inside a food dehydrator (the same ones used for filament drying)
designed to fit dehydrators with the 260mm (I.D.) tray with a 72mm center hole. the height is 33mm. Also designed to be printed in at least a 200x200mm bed
IMPORTANT!!! note the following:
Print with 0 top and bottom shells
4 perimeters (@0.4mm extrusion width)
40% triangle infill in PrusaSlicer (this may vary depending on your slicer and the size of your silica gel, i recommend printing a small sample of the infill first to determine if the silica will pass through or not)
See my attached screenshot for the settings I used
I recommend printing with at least PETG as most dehydrators can reach PLA's glass transition temp, but not PETG or ABS
This is stating the obvious but print 3 of this to maximize the tray capacity. the less silica stacked on top of each other, the faster it will dry
designed to fit dehydrators with the 260mm (I.D.) tray with a 72mm center hole. the height is 33mm. Also designed to be printed in at least a 200x200mm bed
IMPORTANT!!! note the following:
Print with 0 top and bottom shells
4 perimeters (@0.4mm extrusion width)
40% triangle infill in PrusaSlicer (this may vary depending on your slicer and the size of your silica gel, i recommend printing a small sample of the infill first to determine if the silica will pass through or not)
See my attached screenshot for the settings I used
I recommend printing with at least PETG as most dehydrators can reach PLA's glass transition temp, but not PETG or ABS
This is stating the obvious but print 3 of this to maximize the tray capacity. the less silica stacked on top of each other, the faster it will dry
Similar models
thingiverse
free
desiccant capsule by Hecot
...t on the printer heat bed with a sheet of aluminum foil underneath. i think it's better to keep food and fliament separete :)
thingiverse
free
Desiccant Box 150x60mm by wisestone
...and dry out the old desiccant ready for re-use. similary for my filament reel ziplock bags. over time, the...
grabcad
free
Desiccant Box 150x60mm
...and dry out the old desiccant ready for re-use. similary for my filament reel ziplock bags. over time, the...
thingiverse
free
Filament dryer rings/lid for cheap food dehydrators
...siccant bags on an empty spool for drying. if you print in pla, and go much higher in temp, the pla will likely start to deform.
thingiverse
free
Desiccant box, microwaveable by Sprayed
...ulk, by the quart, on amazon, ebay, etc. i recommend either the orange indicator type or orange indicator mixed with clear type.
thingiverse
free
Snap-close dessicant wedges by jongsanders
...rint these in a high temperature-resistant plastic like petg or abs. i used clear petg so i could easily see the indicator color!
thingiverse
free
Desiccant Box 120x60mm by wisestone
... clear filament, with 0.2mm layer height and 15% infill on a prusa i3 mk3s printer.
i hope you can find this design useful, too.
grabcad
free
Desiccant Box 120x60mm
... clear filament, with 0.2mm layer height and 15% infill on a prusa i3 mk3s printer.
i hope you can find this design useful, too.
thingiverse
free
Silica Gel Desiccant / Dehumidifier Box Holder by polysquare
...ttps://www.amazon.com/dry-packs-silica-desiccant-40gm/dp/b006l882nm/
fusion 360, measure, and export link: http://a360.co/2nmx8rj
thingiverse
free
Desiccant Box 190x60mm by wisestone
...um red filament, with 0.2mm layer height and 15% infill on a prusa i3 mk3s printer.
i hope you can find this design useful, too.
Derekcgs
thingiverse
free
Biqu B1 PTFE connector by derekcgs
...rse
connector for ptfe tube. i designed this for use with my drybox.
this was designed to mount under the filament runout sensor
thingiverse
free
Biqu B1 - modified 2 piece fan duct by derekcgs
... fan duct
fitment with the stock biqu b1 fan is a little bit tight, but it still fits. tested perfect fit with replacement fans.
Dehydrator
3d_ocean
$1
Pumpkin Seeds Seamless Background
...tiling pattern • 1024×1024 pix texture • .jpg and flat .png file • tiling texture click here if you need bigger file at photodune
3d_export
$7
electric fruit dryer machine
...electric fruit dryer machine 3dexport fruit dehydrator machine 3d model:<br>dryer include fruits models that are randomly...
sketchfab
$4
Food Dehydrator
...food dehydrator
sketchfab
low poly food dehydrator - food dehydrator - buy royalty free 3d model by sunny (@sunny7610)
thingiverse
free
Dehydrator Extension by fluffywhitewolf
...the trays.
specific dehydrator model : http://www.amazon.com/gp/product/b075zb3v9s/
diameter is 240mm. printed on an ender5plus
thingiverse
free
food dehydrator filamentdryer mod
...ys, so you can still use it as food dehydrator.
the diameter of the dehydrator is 235mm.
rolls up to 100mm width will fit inside.
thingiverse
free
dehydrator with filament outlet by jemad871
...or with filament outlet by jemad871
thingiverse
ring for the cheap diy dehydrator to allow for 2 roles and outlet for 1 filament
thingiverse
free
DIY Filament Dehydrator
...n be used simultaneously to recharge desiccant packets. by printing additional collars more than two reels could be accommodated.
thingiverse
free
Dehydrator Spool Holder by mslivkoff
...he post on the bottom of the dehydrator to hold the filament spool up and allow the warm are to circulate freely around the spool
thingiverse
free
Dehydrator Filament guide and spool holder by 3dphaus
...er by 3dphaus
thingiverse
filament guide and spool holder for food dehydrator.
this is for dehydrator with diameter of 27.5 cm.
thingiverse
free
Lower Tray Westinghouse Dehydrator WFD100W by jtgraphics
...lower tray westinghouse dehydrator wfd100w by jtgraphics
thingiverse
lower tray for westinghouse dehydrator wfd100w
Desiccant
3d_export
$5
filament dry box
...of the box frame is designed to house silica desiccant to remove the moisture within the box to keep...
sketchfab
$10
Desiccator
...br textures
mobile/vr-ready
full collection: lab equipment - desiccator - buy royalty free 3d model by alvin suen (@alvinwcsuen)
thingiverse
free
Desiccant Box by 3dAl
...siccant that you find in gallon jars on amazon. the slots are 2.5 mm so any desiccant larger that that will work.
for dry box
thingiverse
free
Desiccant LockBox by R3LapZ
...desiccant lockbox by r3lapz
thingiverse
designed the hold silca gel/ desiccant. and also to keep pets and children out
thingiverse
free
Desiccant Tube by shawnkampy
...in to be captured without spilling desiccant. it is fully printable. my prints were able to fit together without needing sanding.
thingiverse
free
Desiccant Box by feinripper
...ripper
thingiverse
desiccant box based on a idea of dralion but with a snap on lid and stronger walls.
diameter 60mm
height 73mm
thingiverse
free
Desiccant holder by Battle_bovine
...se
simple magnetic metal desiccant tin holder. sticks to the side of dry box and allows for easy removal and drying in the oven.
thingiverse
free
Forced air desiccant box by MarcJennings
...air desiccant box by marcjennings
thingiverse
desiccant container that uses a noctua 5v 40mm fan to push air past the desiccant.
thingiverse
free
Desiccant Holder by Coder96
...er made to fit in the rubbermaid 1776473 21-cup dry food container. it has clips in the top to fit the wide filament spool holder
thingiverse
free
Desiccant container/holder by apell
...cant container/holder by apell
thingiverse
yet another desiccant container with a screw on lid. 48mm diameter, 2mm square holes.
Silica
3d_export
$10
vray glass cup
...primary constituent of sand. soda-lime glass, containing around 70% silica accounts for around 90% of manufactured glass. the term...
3d_export
$5
filament dry box
...within the box to keep the filament dry. without silica this box will not solely keep the filament...
thingiverse
free
SAO Silica stencil
...sao silica stencil
thingiverse
silica stencil
thingiverse
free
Silica Gel Container
...silica gel container
thingiverse
silica gel container
thingiverse
free
Caja para silica gel - silica gel box by pololoz
...caja para silica gel - silica gel box by pololoz
thingiverse
caja para silica gel.
thingiverse
free
silica gel box by TK_DESIGN
...silica gel box by tk_design
thingiverse
silica gel box
thingiverse
free
Silica Gel Containers by xsgroup
...silica gel containers by xsgroup
thingiverse
silica gel containers...
thingiverse
free
Silica Gel Container by singwanlew
...silica gel container by singwanlew
thingiverse
silica gel container for center of the spool hole.
thingiverse
free
Silica Gel Box by Korgano
...fill this box with silica gel to keep your filament dry.
it features a hole in the middle which increases the surface of the box.
thingiverse
free
Silica gel case (Dreyer) by kmltbtozgl
...silica gel case (dreyer) by kmltbtozgl
thingiverse
silica gel box
Tray
archibase_planet
free
Tray
...tray
archibase planet
tray salver tea-tray
tray 1 n210312 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Tray
...tray
archibase planet
tray salver tea-tray
tray 2 n210312 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$8
tray
...tray
3dexport
design of tray
archibase_planet
free
Tray
...tray
archibase planet
tray salver stand
tray - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Tray
...tray
archibase planet
tray salver
tray n050408 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Tray
...tray
archibase planet
tray salver kitchen ware
tray - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Tray
...tray
archibase planet
tray salver
tray 2 n050408 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Tray
...tray
archibase planet
tray salver kitchen ware
tray n241211 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Tray
...tray
archibase planet
tray salver office ware
tray n160808 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Tray
...tray
archibase planet
donuts donuts tray donut food
tray donuts n190614 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
Food
archibase_planet
free
Food
...food
archibase planet
food fires fast food
food fires n180614 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$10
food
...food
3dexport
this is a table with food.
turbosquid
$10
canteen food, fast food
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$6
Food Truck
...oly low poly food truck truck
low poly food truck for games or animation. it contains of rack, ventilation, stairs, and umbrella.
turbosquid
$3
Food
...osquid
royalty free 3d model food for download as ma and obj on turbosquid: 3d models for games, architecture, videos. (1443013)
3d_export
$5
Food container
...food container
3dexport
food container
3d_export
$5
food box
...food box
3dexport
it is box for food with a cover.
turbosquid
$5
food
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Foods
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
food
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.