Thingiverse
FolgerTech FT-5 Upgraded X-Carriage (piezo bed level option) by lilmikey
by Thingiverse
Last crawled date: 3 years ago
Update 11/15: Switched to a BMG vlone and added a compatible part cooler blower channel for BMG+V6+Volcano. Piezo leveling is still working great and I have switched back and forth between the Aero and BMG with almost no adjustment.
Update 4/8: I received my Aero upgrade kit and converted over. The piezo leveling is still working just fine. The Aero and stock extruder require less Z correction than the full E3D v6 but other than that, nothing else needed to change.
Since the Aero and stock extruder are so much shorter I added a new part cooler that mounts a blower behind the carriage - should work for stock extruder or aero with a volcano.
Update 3/21: Added a version that supports piezo-based bed leveling for anything that mounts to a full size stepper motor. This is very much WIP but it is working for me at the moment. Here's how it works... You'll want to mount a 27mm piezo disk in the recess in the back of the carriage. The recess ridge should support the brass edges of the disc and the center sensor should be facing toward the FRONT of the carriage. A spot of glue on the brass can hold it in place however it will be pressure-held in the recess so I did not find it necessary. The current design has a channel that would indicate the disc could go in the with the sensor facing the back of the carriage however this negatively impacts sensitivity and will not work well. You can glue the wires in the channel to keep them out of the way if you wish.
Next, the 'Piezo Knocker' should be positioned so that the screw holes align with the bottom screws of the NEMA motor. The longer 'knocker' end should face the piezo disk and the larger, flatter end should face the motor. Position the motor and tighten the screws fully - they don't need to be overly tight. Do NOT put in the top screws. The idea is the front of the motor should flex vertically when the nozzle touches the bed pushing on the knocker and flexing the disk. There is also an updated carriage front plate with a little more room for the motor in order to allow for the flex. The knocker is larger than the gap+piezo disk recess so there is some pre-loaded pressure on the disk giving pretty repeatable results as well as holding the motor firmly enough to prevent any negative impacts on print quality. Once you get everything assembled you'll want to tune the vrefs on the board: https://www.youtube.com/watch?v=WDHU3tRU-C4
I'm currently using the piezo as an end stop replacement as things seem to get wonky with the auto bed leveling. I believe that is a tuning/PEBKAC issue and not a design issue though. Here it is performing the bed leveling process: https://youtu.be/MD5Hin9Ter8.
To make this work I made the following changes to the firmware:
In configuration.h:
uncomment #define AUTO_BED_LEVELING_FEATURE -- this will let you use the grid leveling if you wish. You'll want to tweak LEFT/RIGHT/FRONT/BACK_PROBE_BED_POSITION. I used 20 for LEFT/FRONT and 220 for RIGHT/BACK. You can set AUTO_BED_LEVELING_GRID_POINTS as well. 3 seems to be common.
set the X/Y/Z_PROBE_OFFSET_FROM_EXTRUDER to zero. The nozzle is the probe so no offset needed. We will need to adjust the z offset from home via GCODE as there is a small amount of flex required to trigger the sensor and left uncorrected the nozzle will be pressed against the bed for the first layer. However, that requires some tinkering and I do it through the start gcode instead of here.
Increase the Z homing feed rate. By default it's #define HOMING_FEEDRATE {5060, 5060, 1060, 0}. I increased to #define HOMING_FEEDRATE {5060, 5060, 2060, 0}. The nozzle impacting the bed is the piezo trigger. We don't want to be gentle.
Along the same lines, we don't want the 2nd bump to be too gentle. I increased the bump divisor from #define HOMING_BUMP_DIVISOR {2, 2, 4} to #define HOMING_BUMP_DIVISOR {2, 2, 1}.
Then, in the start GCODE I did a couple things:
First I X/Y home the nozzle - this is required for any movements:
G28 X0 Y0
Then I move the nozzle to the middle of the plate - I want to z home at plate center in case there are minor balance variations:
G1 X150 Y150 F5000
I heat the nozzle to 180 to soften any material on the nozzle. Anything crusty will press on the plate and throw off the sensor (update: I have upped this to 210 as some PETG is still stiff at 180):
M109 S210
I home the Z. Make sure to clean up any goo that drops:
G28 Z0
I set a Z offset - this is a bit of trial and error based on the amount of preloaded pressure you have on the disk. If it's more than a couple 1/10s of a mm then recheck your sensitivity and setup:
G92 Z-0.1
Then I move everything back to home:
G1 X0 Y0 Z0 F5000
I've printed a dozen or so prints with the above z homing logic and even swapped out throats without having to change anything wrt z height. I have a pancake stepper on the way and I plan on making a compatible version.
Update 3/11: Added a bottom piece that accessories can be mounted to as well as an attachment for a 50mm blower targeted for a Volcano. I also have a beta for a regular V6 heater block if anyone wants to try it.
This is the modified X-Carriage I have been using on my FT-5. This carriage fixes a number of inconveniences us FT-5 users endure. The differences between this upgraded carriage and the original (https://www.thingiverse.com/thing:1858771) are:
Solid pieces: The rail and motor attach to the same piece. The screws are fully backed - shouldn't bend or break like the default carriage. The attachment holes have divots to ensure everything stays in place and not the straight, tight square holes. All bolt heads and nuts are counter sunk.
Mount for a small 8-circuit terminal block (https://www.amazon.com/Blue-Sea-Systems-Circuit-Terminal/dp/B000S5Q2VS): I change my hot ends, coolers, thermistors, etc often. A terminal block is a lot easier to deal with than crimping every new wire.
Cut out for motor plug: You can remove the motor without having to disassemble the entire carriage. Remove the rear motor screws and it will pull out the front.
I dropped the cable chain but the stock chain should mount to the top holes. I velcroed my cable rope to the rail 'hat' from my dual bowden gantry (https://www.thingiverse.com/thing:2814954).
This is still WIP. Everything works great but I will be creating a part cooler that mounts to the carriage and a piezo sensor mount once the parts arrive.
Update 4/8: I received my Aero upgrade kit and converted over. The piezo leveling is still working just fine. The Aero and stock extruder require less Z correction than the full E3D v6 but other than that, nothing else needed to change.
Since the Aero and stock extruder are so much shorter I added a new part cooler that mounts a blower behind the carriage - should work for stock extruder or aero with a volcano.
Update 3/21: Added a version that supports piezo-based bed leveling for anything that mounts to a full size stepper motor. This is very much WIP but it is working for me at the moment. Here's how it works... You'll want to mount a 27mm piezo disk in the recess in the back of the carriage. The recess ridge should support the brass edges of the disc and the center sensor should be facing toward the FRONT of the carriage. A spot of glue on the brass can hold it in place however it will be pressure-held in the recess so I did not find it necessary. The current design has a channel that would indicate the disc could go in the with the sensor facing the back of the carriage however this negatively impacts sensitivity and will not work well. You can glue the wires in the channel to keep them out of the way if you wish.
Next, the 'Piezo Knocker' should be positioned so that the screw holes align with the bottom screws of the NEMA motor. The longer 'knocker' end should face the piezo disk and the larger, flatter end should face the motor. Position the motor and tighten the screws fully - they don't need to be overly tight. Do NOT put in the top screws. The idea is the front of the motor should flex vertically when the nozzle touches the bed pushing on the knocker and flexing the disk. There is also an updated carriage front plate with a little more room for the motor in order to allow for the flex. The knocker is larger than the gap+piezo disk recess so there is some pre-loaded pressure on the disk giving pretty repeatable results as well as holding the motor firmly enough to prevent any negative impacts on print quality. Once you get everything assembled you'll want to tune the vrefs on the board: https://www.youtube.com/watch?v=WDHU3tRU-C4
I'm currently using the piezo as an end stop replacement as things seem to get wonky with the auto bed leveling. I believe that is a tuning/PEBKAC issue and not a design issue though. Here it is performing the bed leveling process: https://youtu.be/MD5Hin9Ter8.
To make this work I made the following changes to the firmware:
In configuration.h:
uncomment #define AUTO_BED_LEVELING_FEATURE -- this will let you use the grid leveling if you wish. You'll want to tweak LEFT/RIGHT/FRONT/BACK_PROBE_BED_POSITION. I used 20 for LEFT/FRONT and 220 for RIGHT/BACK. You can set AUTO_BED_LEVELING_GRID_POINTS as well. 3 seems to be common.
set the X/Y/Z_PROBE_OFFSET_FROM_EXTRUDER to zero. The nozzle is the probe so no offset needed. We will need to adjust the z offset from home via GCODE as there is a small amount of flex required to trigger the sensor and left uncorrected the nozzle will be pressed against the bed for the first layer. However, that requires some tinkering and I do it through the start gcode instead of here.
Increase the Z homing feed rate. By default it's #define HOMING_FEEDRATE {5060, 5060, 1060, 0}. I increased to #define HOMING_FEEDRATE {5060, 5060, 2060, 0}. The nozzle impacting the bed is the piezo trigger. We don't want to be gentle.
Along the same lines, we don't want the 2nd bump to be too gentle. I increased the bump divisor from #define HOMING_BUMP_DIVISOR {2, 2, 4} to #define HOMING_BUMP_DIVISOR {2, 2, 1}.
Then, in the start GCODE I did a couple things:
First I X/Y home the nozzle - this is required for any movements:
G28 X0 Y0
Then I move the nozzle to the middle of the plate - I want to z home at plate center in case there are minor balance variations:
G1 X150 Y150 F5000
I heat the nozzle to 180 to soften any material on the nozzle. Anything crusty will press on the plate and throw off the sensor (update: I have upped this to 210 as some PETG is still stiff at 180):
M109 S210
I home the Z. Make sure to clean up any goo that drops:
G28 Z0
I set a Z offset - this is a bit of trial and error based on the amount of preloaded pressure you have on the disk. If it's more than a couple 1/10s of a mm then recheck your sensitivity and setup:
G92 Z-0.1
Then I move everything back to home:
G1 X0 Y0 Z0 F5000
I've printed a dozen or so prints with the above z homing logic and even swapped out throats without having to change anything wrt z height. I have a pancake stepper on the way and I plan on making a compatible version.
Update 3/11: Added a bottom piece that accessories can be mounted to as well as an attachment for a 50mm blower targeted for a Volcano. I also have a beta for a regular V6 heater block if anyone wants to try it.
This is the modified X-Carriage I have been using on my FT-5. This carriage fixes a number of inconveniences us FT-5 users endure. The differences between this upgraded carriage and the original (https://www.thingiverse.com/thing:1858771) are:
Solid pieces: The rail and motor attach to the same piece. The screws are fully backed - shouldn't bend or break like the default carriage. The attachment holes have divots to ensure everything stays in place and not the straight, tight square holes. All bolt heads and nuts are counter sunk.
Mount for a small 8-circuit terminal block (https://www.amazon.com/Blue-Sea-Systems-Circuit-Terminal/dp/B000S5Q2VS): I change my hot ends, coolers, thermistors, etc often. A terminal block is a lot easier to deal with than crimping every new wire.
Cut out for motor plug: You can remove the motor without having to disassemble the entire carriage. Remove the rear motor screws and it will pull out the front.
I dropped the cable chain but the stock chain should mount to the top holes. I velcroed my cable rope to the rail 'hat' from my dual bowden gantry (https://www.thingiverse.com/thing:2814954).
This is still WIP. Everything works great but I will be creating a part cooler that mounts to the carriage and a piezo sensor mount once the parts arrive.
Similar models
thingiverse
free
Proximity sensor mount for Satour E3D carriage. by Eli-Audio
...roximity sensor for auto-homing z-axes or software auto-bed-leveling. the mount can be fitted on the back of the extruder cooler.
thingiverse
free
Ender 3 Underbed Piezo by Heracles421
... to print a pcb holder arm, it must go on the front right corner of the bed. for the rest of the arms follow the order in step 4.
thingiverse
free
Aus 3D IR Sensor mount for Titan Aero by Tailslide
...rk as it is not adjustable.
update 2018-12-17: added an improved mount that is stronger and interferes less with my heater wires.
thingiverse
free
Tronxy XY-08n mount for e3d v6 Carriage by TNS by aplocher
... -1 // y offset: -front +behind [the nozzle]
#define z_probe_offset_from_extruder -1 // z offset: -below +above [the nozzle]
thingiverse
free
Anet A8 Front Fan Sensor Mount 18 mm by buzzkc
...://www.thingiverse.com/thing:2506274
the wiring schematic and parts list for my sensor: https://www.thingiverse.com/thing:2758533
thingiverse
free
BETA - Piezo z-probe for E3D Titan Aero (mounted direct via motor) by DjDemonD
...thingiverse precision piezo presents - titan aero (or other similar extruder system) piezo sensor plate. this is a beta,...
thingiverse
free
Piezo adapter for 3-Wheeled/Linear Rail D-Bot Carriage by coredump777
... screws holding the adapter to the carriage front. you want it to be able to bend slightly but not enough to matter during print.
thingiverse
free
Piezo electric Auto bed leveling sensor installed on my Dual head nozzel
...//www.thingiverse.com/thing:2161827
link to my dual head design including direct drive: https://www.thingiverse.com/thing:3578669
thingiverse
free
E3D v5 or v6 X-Carriage mount for standard Prusa i3 by BoByS
...for the motors of it, you can mount the whole holder on the 2 bottom holes - this will rise the maximum z axis travel with ~20mm.
thingiverse
free
Threaded 8mm Inductive Sensor Mount for 5015 Fan (Anet A8 bed leveling) by TabLeft
...robe_bed_position 15
#define right_probe_bed_position 180
#define front_probe_bed_position 15
#define back_probe_bed_position 160
Lilmikey
thingiverse
free
Breckenridge, CO by lilmikey
...e places to ski and i was surprised that noone had made it before.
the map screenshot should correlate pretty close to the model.
thingiverse
free
2x2 Board Mount by lilmikey
...ood cross beam in place. it was part of my visual pinball cabinet build: http://lilmikey.com/2017/02/16/virtual-pinball-cabinet/
thingiverse
free
FJ Cruiser Power Outlet Cover by lilmikey
...r power outlet cover by lilmikey
thingiverse
broke the power outlet (cigarette lighter) cover on my fj cruiser. made a new one.
thingiverse
free
Vertical HDD Bracket by lilmikey
...02/16/virtual-pinball-cabinet/
i designed and printed this simple bracket to hold the drive vertically and mount to a wood panel.
thingiverse
free
Colorado Seat-back Hanger by lilmikey
... of your chevy colorado seat? here's a clip...
it's wide and contoured to the seat to prevent damage from heavier items.
thingiverse
free
GoPro Taut Strap Mount by lilmikey
...trap slots are split on one end and there's just enough flex to slide a strap through. i designed it for my hiking backpack.
thingiverse
free
AA / 18650 Battery Tray by lilmikey
...ep by my batter charger. i put the 'dead' batteries in the middle tray and the charged batteries in the vertical stands.
thingiverse
free
Motherboard Standoffs by lilmikey
...ape controller, and sainsmart relay board in my pinball cabinet project: http://lilmikey.com/2017/02/16/virtual-pinball-cabinet/
thingiverse
free
Lowrance Direct-Rail Mount by lilmikey
...or strength.
there are two stls on this item. one that mounts the ff parallel to the rail and one that mounts it at a 20% angle.
thingiverse
free
GoPro Snap Base by lilmikey
...ht be an issue since the arms have to flex without breaking. my petg prints seem to work well - perhaps even a bit too flexible.
Folgertech
thingiverse
free
FolgerTech Kossel Rev B Parts by thosmos
...folgertech kossel rev b parts by thosmos
thingiverse
stock folgertech kossel rev b parts
thingiverse
free
Adjustable Z endstop Folgertech 2020 by Joe558
...adjustable z endstop folgertech 2020 by joe558
thingiverse
this is an adjustable z endstop for the folgertech prusa i3 2020.
thingiverse
free
Folgertech Kossel Power supply cover by J7R3AN
...kossel power supply cover by j7r3an
thingiverse
power supply cover for the folgertech kossel with a mount for a plug and switch.
thingiverse
free
Folgertech FT-5 extruder cable holder by thomasdr
...folgertech ft-5 extruder cable holder by thomasdr
thingiverse
folgertech ft-5 extruder cable managment.
thingiverse
free
Filament Guide - Folgertech Prusa I3 by Gerdarumba
...h prusa i3 by gerdarumba
thingiverse
filament guide for a folgertech prusa i3 - acrylic.
designed to fit the 6mm acrylic frame.
thingiverse
free
Folgertech E3D Direct Drive Inductive Proximity Mounts by phpapple
...
modified mount for the folgertech prusa i3 that supports an inductive proximity sensor. uses the stock folgertech screw holes.
thingiverse
free
Folgertech Prusa I3 2020 power supply bracket by ahntorage
...folgertech prusa i3 2020 power supply bracket by ahntorage
thingiverse
power supply brackets for folgertech i3 prusa
thingiverse
free
FolgerTech i3 BLTouch and Fan Mount by kedibekar3D
...ch prusa i3 fan + bltouch mount, adjusted for clearance.
works with fan manifold from: http://www.thingiverse.com/thing:1161013
thingiverse
free
Folgertech FT5 Head 2D by tauscnc
...in 2d dxf format.
note: linear bearing is 26.95 mm width but my drawing is set at 26.50 to allow some compression of wood parts.
thingiverse
free
Folgertech FT-5 Z End Stop Mount by thomasdr
...folgertech ft-5 z end stop mount by thomasdr
thingiverse
folgertech ft-5 z end stop mount for the left side.
Piezo
turbosquid
$5
Buzzer Piezo
...odel buzzer piezo for download as max, max, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1607700)
3d_export
$7
buzzer piezo
...;all materials are logically named<br>the main format is in 3ds max 2013.<br>satisfaction guarranteed<br>thanks
3d_export
$15
Buzzer 3D Model
...audio electronic component signalling piezoelectric disk alarm timer electric piezo industrial part electrical bell doorbell buzzer 3d model download...
thingiverse
free
Hypercube_evolution E3D_Titan_Aero with piezo
...ercube_evolution e3d_titan_aero with piezo
thingiverse
hypercube_evolution a piezo z-axis sensor was attached to e3d_titan_aero.
thingiverse
free
Precision-Piezo Probe with 3 Piezo 15mm by Tech-Raton
...if bigger, you'll lose the piezo marks)
you just have to slide the part between the heatsink and the effector (or your mount)
thingiverse
free
Piezo Chimera mount by RKS7204
...piezo chimera mount by rks7204
thingiverse
mount for e3d chimera hotend and piezo sensor
thingiverse
free
Piezo v1.22 Mount by Suggy
...piezo v1.22 mount by suggy
thingiverse
mount for under bed piezo censor pcb
thingiverse
free
Precision Piezo - 27mm and 20mm Piezo Disc drill guide. by DjDemonD
... djdemond
thingiverse
drilling guide for piezo discs to centre your drill.
see youtube video here: https://youtu.be/ms1fd0v5z68
thingiverse
free
Underbed Piezo Mounts by fcollingwood
...the piezos are smooth. two of the arms a required and two of the mirror arms are required
everything else can be printed at 0.2mm
thingiverse
free
(Beta) Piezo UnderBed Mounts by Precision Piezo by DjDemonD
...sulation to the mounts to keep heat from the bed away from the piezos.
future release might include some clamps on the top parts.
Ft
3ddd
free
Renault FT-17
...renault ft-17
3ddd
ft-17 , renault , танк
turbosquid
$85
40 ft container
...id
royalty free 3d model 40 ft container for download as max on turbosquid: 3d models for games, architecture, videos. (1154866)
turbosquid
$45
container 40 ft
...id
royalty free 3d model container 40 ft for download as max on turbosquid: 3d models for games, architecture, videos. (1480343)
turbosquid
$85
Renault FT-17
...yalty free 3d model renault ft-17 for download as 3ds and max on turbosquid: 3d models for games, architecture, videos. (1145251)
turbosquid
$5
NVidia FT 03
... 3d model nvidia ft 03 for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1233064)
turbosquid
$25
Container 20 ft
...l container 20 ft for download as 3ds, max, obj, fbx, and upk on turbosquid: 3d models for games, architecture, videos. (1384306)
turbosquid
$25
FT Buck Saw
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
free
Jaga - Maxi FT-10
... om
радиатор jaga - maxi ft-10
width: 63 cm
depth: 13 cm
height: 59 cm
сайт производителя:http://www.jaga.be/
turbosquid
$45
20 ft container
...ontainer for download as blend, blend, dae, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1516815)
turbosquid
$35
Yaesu FT-897D Transceiver
...y free 3d model yaesu ft-897d transceiver for download as max on turbosquid: 3d models for games, architecture, videos. (1160274)
Carriage
archibase_planet
free
Carriage
...arriage
archibase planet
perambulator baby carriage pram
carriage n250908 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
free
carriage
...carriage
3dexport
old fashion carriage model, more files here:
turbosquid
$140
Carriage
...urbosquid
royalty free 3d model carriage for download as max on turbosquid: 3d models for games, architecture, videos. (1482052)
turbosquid
$25
Carriage
...urbosquid
royalty free 3d model carriage for download as max on turbosquid: 3d models for games, architecture, videos. (1285944)
3d_export
free
carriage
...carriage
3dexport
game cart
3d_ocean
$15
Barrel Carriage
...ieval oak old transport wheels wine wood
this model contains a barrel and a carriage. it is a medieval type of wood oak carriage.
turbosquid
$40
Carriage
...ty free 3d model carriage for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1290094)
turbosquid
free
Carriage
...yalty free 3d model carriage for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1239157)
3d_export
$5
Medieval carriage
...medieval carriage
3dexport
medieval carriage in fairy style
turbosquid
$58
Carriage
...d model carriage with scene for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1276262)
Upgraded
turbosquid
$15
Upgraded Glock
...e 3d model upgraded glock for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1185950)
3ddd
$1
Calligaris / UPGRADE
...calligaris / upgrade
3ddd
calligaris
c материалом
3d_export
free
cz upgrade
...cz upgrade
3dexport
https://www.buymeacoffee.com/mestrezen3d https://linktr.ee/mestrezen3
turbosquid
$80
Custer Tank upgrade
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$39
Domestos 1 upgrade
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
Upgraded tea cup
...upgraded tea cup
3dexport
a cup with an unusual design and a unique shape for a more enjoyable tea experience
3d_export
$8
dixy outlander classic style upgraded poplar wood lounge chair
...utlander classic style upgraded poplar wood lounge chair
3dexport
dixy outlander classic style upgraded poplar wood lounge chair
turbosquid
free
AK-12 + Upgrades low-poly 3D model
...ow-poly 3d model for download as fbx, blend, and unitypackage on turbosquid: 3d models for games, architecture, videos. (1501145)
evermotion
$700
Upgrade from V-ray 1.5 to 3.5 for 3ds max
...here is no need to purchase a new dongle - your current dongles will be reprogrammed to carry v-ray 3. evermotion 3d models shop.
evermotion
$300
Upgrade from V-Ray 2.0 to V-ray 3.5 for 3ds Max
... interface (gui) for editing settings on one machine and one render node for rendering on one machine. evermotion 3d models shop.
Level
design_connected
$11
Levels
...levels
designconnected
one nordic levels computer generated 3d model. designed by form us with love.
design_connected
$7
Level
...level
designconnected
zanotta level shelves and storage computer generated 3d model. designed by arik levy.
turbosquid
$29
level
...ty free 3d model level for download as 3ds, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1272856)
turbosquid
$1
level
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Mario level
...mario level
3dexport
mario level low quality for fun videos
3ddd
$1
LEVELS OF DISCOVERY
...етская мебель "levels of discovery". rab10003 princess mini rocker
кресло-качалка (мини) "принцесса навсегда"
3d_export
$19
level design
...level design
3dexport
you can use this design (level design) in your own game.
turbosquid
$60
Desert level
...squid
royalty free 3d model desert level for download as fbx on turbosquid: 3d models for games, architecture, videos. (1208131)
turbosquid
$15
Transit Level
...quid
royalty free 3d model transit level for download as max on turbosquid: 3d models for games, architecture, videos. (1158112)
turbosquid
$14
Districts Level
...id
royalty free 3d model districts level for download as max on turbosquid: 3d models for games, architecture, videos. (1408410)
Bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
free
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
free
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
Bed
...bed
3ddd
bed , постельное белье , постель
bed
3d_export
$7
bed adairs bed
...rs bed
3dexport
bed adairs bed in modern style. if you want a smoother surface, please turn on turbosmooth in the modifier list.
Option
3ddd
$1
Фритюр SG14S with Options
...фритюр sg14s with options
3ddd
фритюр
проф. фритюр sg14s with options
3d_ocean
$15
trophy options
...e material property props trophy winner
-trophy options -low polys -obj, fbx,blender, 3ds. -zip : 5.7 mb - include gold material.
turbosquid
$2
keyboard 3 options
...oyalty free 3d model keyboard 3 options for download as blend on turbosquid: 3d models for games, architecture, videos. (1711408)
design_connected
$18
Swivel Chairs with Footrest Option
...swivel chairs with footrest option
designconnected
swivel chairs with footrest option computer generated 3d model.
design_connected
$16
Swivel Armchairs with Footrest Option
...swivel armchairs with footrest option
designconnected
swivel armchairs with footrest option computer generated 3d model.
3d_export
$19
1955 sideboard 3 options
...1955 sideboard 3 options
3dexport
turbosquid
$29
Office Chair with Multi Options
... 3d model office chair with multi options for download as max on turbosquid: 3d models for games, architecture, videos. (1380794)
turbosquid
$25
claddagh ring two options
...y free 3d model claddagh ring two options for download as 3dm on turbosquid: 3d models for games, architecture, videos. (1673087)
turbosquid
$20
PADDY PLANE OPTION 12
...yalty free 3d model paddy plane option 12 for download as max on turbosquid: 3d models for games, architecture, videos. (1696286)
turbosquid
$18
pendant sun three options
...free 3d model pendant sun three options for download as 3dm on turbosquid: 3d models for games, architecture, videos. (1555386)
5
turbosquid
$6
Rock 5-5
...urbosquid
royalty free 3d model rock 5-5 for download as obj on turbosquid: 3d models for games, architecture, videos. (1639063)
3d_export
$5
hinge 5
...hinge 5
3dexport
hinge 5
turbosquid
$10
A-5
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
A-5
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
Calligraphic Digit 5 Number 5
...hic digit 5 number 5 for download as max, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1389333)
3ddd
$1
5 роз
...5 роз
3ddd
5 роз в стеклянной вазе
design_connected
$11
iPhone 5
...iphone 5
designconnected
apple iphone 5 computer generated 3d model.
3ddd
$1
Lola 5
...lola 5
3ddd
miniforms
lola 5 miniforms 300*65*134
3ddd
$1
Nexus 5
...dd
nexus , phone , телефон
google nexus 5 phone
3d_ocean
$15
iPhone 5
...iphone 5
3docean
3d 4d apple cinema iphone model modeling phone screen texture
iphone 5 3d model and texture realistic iphone 5.