Thingiverse
Foldable Brushed Microquad by ulflindestrom
by Thingiverse
Last crawled date: 3 years ago
This one doesn't make much sense (since when are micros too big?), but it's cute...
83x58mm when folded, 138mm motor-to-motor (diagonally) when unfolded. So no, its not very micro, I know. And it's one heavy micro, don't expect to do any acro with it. I designed it mostly because I had an idea and I like to draw stuff ;)
The Quanum micro camera/vtx combo from HobbyKing fits perfectly and the camera angle is adjustable between 0 and 30 degrees. The arms have slots for clean wiring and to prevent accidental cutting of motor wires when folding the arms.
I'm running mine with the following hardware:
Beef's Brushed Board (flashed with Betaflight)https://www.fpvheadquarters.com/beef-s-brushed-board.html
8.5mm (outer diameter) brushed motorshttps://www.fpvheadquarters.com/angry-beez-8mm-brushed-motor-set.htmlhttp://www.banggood.com/Chaoli-CL-820-8_5x20mm-Coreless-Motor-for-90mm-150mm-DIY-Micro-FPV-RC-Quadcopter-Frame-p-1054803.html
Parrot Rolling Spider propellershttp://www.ebay.com/itm/4x-Propellers-Props-Replacement-Blade-for-Parrot-Mini-Drones-Rolling-Spider-New-/
Fissel micro frsky rx (only if you have a FrSky compatible transmitter e.g Taranis)https://www.fpvheadquarters.com/microfrx-receiver.html
750 mah 1S Lipo (a bit too big though)http://www.hobbyking.com/hobbyking/store/__41271__Turnigy_nano_tech_750mAh_1S_35_70C_Lipo_Pack_Walkera_V120D02S_QR_Infra_X_QR_W100S_.html
Micro camera/vtx combohttp://www.hobbyking.com/hobbyking/store/__89777__Quanum_ELITE_TX_CAMERA_COMBO_Micro_Cam_VTX_25mW_40CH_5_8GHz_NTSC_.htmlhttp://www.banggood.com/Eachine-MC01-AIO-5_8G-40CH-25MW-VTX-600TVL-13-Cmos-FPV-Camera-p-1065228.html
If you use a Beef's Brushed Board you'll also need an FTDI adapter to communicate with the boardhttp://www.ebay.com/sch/i.html?_from=R40&_trksid=p2050601.m570.l1313.TR0.TRC0.H0.Xusb+ftdi.TRS0&_nkw=usb+ftdi&_sacat=0
I used the setup above mainly because I already had all the necessary parts at home, there are (most likely) better/cheaper parts out there if you google. There are also a bunch of links in the comments to alternate hardware
Here's a good page to get you started with hardware similar to the one listed abovehttps://oscarliang.com/fpv-micro-quad-beef-board/
UPDATE 160709:
Added new arms with slits for the motors (as shown in the pictures). Uploaded the wrong version previously, sorry
UPDATE 160716:
Added new, thicker arms for you guys who prints in PLA. These should hold up better in a crash. Also, user unclecracker made a remix of the arms to fit 7mm motors: http://www.thingiverse.com/thing:1675767
UPDATE 170209
Here's a nice camera mount for the Eachine TX03 (and probably other AiOs as well) by murrayp0473http://www.thingiverse.com/thing:2094946
83x58mm when folded, 138mm motor-to-motor (diagonally) when unfolded. So no, its not very micro, I know. And it's one heavy micro, don't expect to do any acro with it. I designed it mostly because I had an idea and I like to draw stuff ;)
The Quanum micro camera/vtx combo from HobbyKing fits perfectly and the camera angle is adjustable between 0 and 30 degrees. The arms have slots for clean wiring and to prevent accidental cutting of motor wires when folding the arms.
I'm running mine with the following hardware:
Beef's Brushed Board (flashed with Betaflight)https://www.fpvheadquarters.com/beef-s-brushed-board.html
8.5mm (outer diameter) brushed motorshttps://www.fpvheadquarters.com/angry-beez-8mm-brushed-motor-set.htmlhttp://www.banggood.com/Chaoli-CL-820-8_5x20mm-Coreless-Motor-for-90mm-150mm-DIY-Micro-FPV-RC-Quadcopter-Frame-p-1054803.html
Parrot Rolling Spider propellershttp://www.ebay.com/itm/4x-Propellers-Props-Replacement-Blade-for-Parrot-Mini-Drones-Rolling-Spider-New-/
Fissel micro frsky rx (only if you have a FrSky compatible transmitter e.g Taranis)https://www.fpvheadquarters.com/microfrx-receiver.html
750 mah 1S Lipo (a bit too big though)http://www.hobbyking.com/hobbyking/store/__41271__Turnigy_nano_tech_750mAh_1S_35_70C_Lipo_Pack_Walkera_V120D02S_QR_Infra_X_QR_W100S_.html
Micro camera/vtx combohttp://www.hobbyking.com/hobbyking/store/__89777__Quanum_ELITE_TX_CAMERA_COMBO_Micro_Cam_VTX_25mW_40CH_5_8GHz_NTSC_.htmlhttp://www.banggood.com/Eachine-MC01-AIO-5_8G-40CH-25MW-VTX-600TVL-13-Cmos-FPV-Camera-p-1065228.html
If you use a Beef's Brushed Board you'll also need an FTDI adapter to communicate with the boardhttp://www.ebay.com/sch/i.html?_from=R40&_trksid=p2050601.m570.l1313.TR0.TRC0.H0.Xusb+ftdi.TRS0&_nkw=usb+ftdi&_sacat=0
I used the setup above mainly because I already had all the necessary parts at home, there are (most likely) better/cheaper parts out there if you google. There are also a bunch of links in the comments to alternate hardware
Here's a good page to get you started with hardware similar to the one listed abovehttps://oscarliang.com/fpv-micro-quad-beef-board/
UPDATE 160709:
Added new arms with slits for the motors (as shown in the pictures). Uploaded the wrong version previously, sorry
UPDATE 160716:
Added new, thicker arms for you guys who prints in PLA. These should hold up better in a crash. Also, user unclecracker made a remix of the arms to fit 7mm motors: http://www.thingiverse.com/thing:1675767
UPDATE 170209
Here's a nice camera mount for the Eachine TX03 (and probably other AiOs as well) by murrayp0473http://www.thingiverse.com/thing:2094946
Similar models
thingiverse
free
Micro FPV Quad Frame by jason51873
...ponents used:
8.5mm brushed motors
beef's brushed board
microfrx receiver - frsky compatible
hyperion quanum elite camera/vtx
thingiverse
free
whoop brushed 8.5 mm
...super-mini-025mw50mw200mw-switchable-aio-5_8g-72ch-vtx-600tvl-13-cmos-fpv-camera-p-1104884.html?rmmds=search&cur_warehouse=cn
thingiverse
free
Micro 105; Eachine EF-01 by Bongo_1st
...icro 105 frame.
kamera: https://www.banggood.com/de/eachine-ef-01-aio-5_8g-40ch-25mw-vtx-800tvl-13-cmos-fpv-camera-p-1064301.html
thingiverse
free
eachine camera holder e010 ef01 90mm by Dinochio
...ro-mini-fpv-quadcopter-frame-kit-2mm-support-8_5x20mm-coreless-motor-p-1055212.html
you can also use a rubber band to fix the cam
thingiverse
free
VTX + micro camera support for micro quadcopter by PiPPi
...x is:http://www.hobbyking.com/hobbyking/store/__43722__skyzone_fpv_5_8ghz_600mw_32ch_a_v_transmitting_tx_module_ts832_rp_sma.html
thingiverse
free
Whoop or E010 Camera Mount by lmbcruz
...tbee-fb90-micro-racing-quadcopter-spare-parts-5_8g-25mw-48ch-vtx-520tvl-cmos-14-camera-p-1108072.html
i printed this in red petg.
thingiverse
free
FPV Racer "Pickup" by lentaa
...fpv_transmitter_v2_.html
camera :http://www.hobbyking.com/hobbyking/store/__88105__aomway_700tvl_camera_ntsc_version_for_fpv.html
thingiverse
free
POD 76mm Micro FPV Quad by DwarfStarFPV
...m-ppm-sbus-output-p-1140478.html?rmmds=search&cur_warehouse=cn
enjoy and go follow @dwarfstardrones on instagram and youtube.
thingiverse
free
Tetard by Ponpont
...ps 55mm (http://www.hobbyflip.com/p/84/httpwwwhobbyflipcomp84walkera-qr-ladybird-propellers-blades-props-5x)
have a good flight !
thingiverse
free
Eachine EF-01 Camera mount for the Eachine E010 quadcopter by slibbinas
...er-rtf-p-1066972.html
camerahttp://www.banggood.com/eachine-ef-01-aio-5_8g-40ch-25mw-vtx-800tvl-13-cmos-fpv-camera-p-1064301.html
Ulflindestrom
thingiverse
free
ULTri SMA Support by ulflindestrom
... standoffs on the ultri which allows for a clean install of the vtx horizontally
this will only be usefull for the vtail config
thingiverse
free
Dremel propeller cutter by ulflindestrom
... fits a dremel or cotech multitool
fully adjustable propsize betwwen 2.5" and 5" but also snaps to every 0.5" step
thingiverse
free
Antenna Guard for ulflindestrom's Brushed FPV Microquad by henbach
...p://www.thingiverse.com/thing:1398182) and needed some more protection for my vtx antenna, so i made this little bolt on antenna.
thingiverse
free
Tweaker LED bars by ulflindestrom
...unch of led bars for the shendrones tweaker miniquad.
designed to use a 10mm wide rgb-led strip (60 leds/m) cut down to six leds
thingiverse
free
Loaded Dice by ulflindestrom
...wo color piece. if you don't have dual extruders you can just print the solid part and add some color to the dots with a pen.
thingiverse
free
ULTri Mini Tricopter - Leg by ulflindestrom
...
although designed specifically for the ultri mini tricopter this leg will fit other multirotor arms with a 16/19mm hole pattern.
thingiverse
free
Foldable Brushed Microquad (ulflindestrom) for Custom FPV by maxdefeijter
... ulflindestrom mentioned that my liscense was not as restrictive and that people could easily steal his files, so i removed them.
thingiverse
free
Micro Spider Quadcopter by ulflindestrom
...ions as for the vtail
update 151221:
added a skirt without holes for motor wires since they are unnecessary for the spider config
thingiverse
free
GoPro Mount for FPV-Reconn RD230/RD290 by ulflindestrom
...ro mount that fits the fpv-reconn rd230 miniquad and rd290 minihex
complete with a m5 nylon lock nut and you're ready to go
thingiverse
free
UL105 Micro Quad Accessories by ulflindestrom
...ly
the prop guards requires quite a lot of support, unless you've got a good printer, sorry about that, i might redesign them
Microquad
thingiverse
free
Tie Fighter MicroQuad by Barry_Barrera
...tie fighter microquad by barry_barrera
thingiverse
fly and rnjoy your new tie fighter microquad
thingiverse
free
MicroQuad frame by cacer
...microquad frame by cacer
thingiverse
frame for microquadcopter
thingiverse
free
Shadow 95mm Microquad by DwarfStarFPV
...d
follow me on instagram for weekly updates on new microquads @3dprint_rcrt
as always print it, build it, share it and have fun !
thingiverse
free
Foldable Brushed Microquad 7mm Mounts by unclecracker
...ulflindestrom's foldable brushed microquad to fit 7mm motors instead of 8.5mm ones.
i remixed it to fit the hubsan x4 motors.
thingiverse
free
X-Frame85 MicroQuad Box by 4runner
...ilament pla black, 2.85mm
best value filament pla snowwhite, 2.85mm
montage:
quad, charger, props, lipos rein und deckel drauf...
thingiverse
free
Antenna Guard for ulflindestrom's Brushed FPV Microquad by henbach
...p://www.thingiverse.com/thing:1398182) and needed some more protection for my vtx antenna, so i made this little bolt on antenna.
thingiverse
free
Foldable Brushed Microquad Camera Mount by r1b4z01d
...croquad camera mount by r1b4z01d
thingiverse
i added some walls to hold the camera in better. i plan to print this later today.
thingiverse
free
6mm microquad with top plate by VPCTech
...es and lightened up the base plate to compensate the extra weight.
thanks to brod for the perfectly simple starting point.
cheers
thingiverse
free
MicroQuad v0.4 by mduca
...ils coming soon.
parts list
1x hobby king jr-wl-fd02r rev02 main board
4x sourced 7mm motors qr series ladybird - wltoys v939
thingiverse
free
Brushed MicroQuad
...020-10x20mm-coreless-motor-for-90mm-150mm-diy-micro-fpv-rc-quadcopter-frame-p-1106428.html?rmmds=myorder
thank you for reading :)
Foldable
3d_ocean
$5
Foldable Wooden Stool
...bench chair foldable furnishing furniture interior low poly portable stool table wood
3d foldable wooden stool with wood texture.
turbosquid
$15
Foldable Stretcher
...l foldable stretcher for download as blend, obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1648935)
turbosquid
$12
Foldable sunglasses
...able sunglasses for download as blend, dae, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1576100)
turbosquid
$8
Foldable Saw
...model foldable saw for download as ma, max, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1178558)
turbosquid
$15
Foldable Room Screen
...foldable room screen for download as blend, dae, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1683049)
turbosquid
$10
Foldable plastic chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$9
3d foldable chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Foldable shop sign
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$59
Beats Headphones Foldable
...le for download as max, 3ds, fbx, obj, dae, dxf, ige, and stl on turbosquid: 3d models for games, architecture, videos. (1683298)
turbosquid
$3
Country style foldable table
...el country style foldable table for download as fbx and blend on turbosquid: 3d models for games, architecture, videos. (1326099)
Brushed
3d_export
free
brush
...brush
3dexport
brush
3d_export
free
brush
...brush
3dexport
it is brush
archibase_planet
free
Brush
...brush
archibase planet
brush toilet brush sanitary ware
brush - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Brush
...rush
archibase planet
rack brush cleaner toilet brush sanitary ware
brush - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Brush
...brush
archibase planet
brushes
brush - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Brush
...brush
archibase planet
?oilet brush sanitary ware
brush - 3d model (*.gsm+*.3ds) for interior 3d visualization.
design_connected
$11
Brushes
...brushes
designconnected
smallaccents brushes computer generated 3d model.
turbosquid
$1
Brush
...rush
turbosquid
royalty free 3d model brush for download as on turbosquid: 3d models for games, architecture, videos. (1391784)
3d_export
$5
brush
...brush
3dexport
comb
turbosquid
$10
Brush
...squid
royalty free 3d model brush for download as ma and obj on turbosquid: 3d models for games, architecture, videos. (1191257)