Thingiverse
Flying Clamp for Tennis stringing - IMPROVED CLAMPING by sashalex007
by Thingiverse
Last crawled date: 3 years, 4 months ago
Yet another remix of edo_mae's excellent design. With this design I have eliminated the need for eyebolts with a fully 3D-printed shaft & threaded stopper. This mechanism is loosely based on the Stringway design providing improved clamping, and improved ergonomics. I have tested these designs with over 70lbs of tension.
With this remix I am also introducing a triple flying clamp (see Stringway clamps) for minimal tension loss due to drawback. Very useful for tie-offs.
PRINTING
It is important to note, that this design is intended for printing with carbon-fibre nylon, however I suspect ABS and PETG might work if all parts are printed at 90-100% density (lines). Recommended densities (%) are for CF nylon, 4 walls.
DOUBLE FLYING CLAMP
side_hexNut.stl -- 50%
side_noHexNut.stl --50%
2x middle_doubleClamp.stl --50%
shaft_doubleClamp --90%
lever.stl --90%
stopper.stl --90%
washer.stl --90%
guide.stl -- 50%
1/4 hex bolt 1.5 inch
1/4 lock nut
3/16 bolt 1 inch
8x 6x3mm round neodymium magnets
TRIPLE FLYING CLAMP
side_hexNut.stl -- 50%
side_noHexNut.stl --50%
2x middle_tripleClamp_outer.stl --50%
middle_tripleClamp_inner1.stl --50%
middle_tripleClamp_inner2.stl --50%
shaft_tripleClamp --90%
lever.stl --90%
stopper.stl --90%
washer.stl --90%
guide.stl -- 50%
1/4 hex bolt 2 inch (I didn't have one so there is an eye bolt in the image)
1/4 lock nut
3/16 bolt 1 inch
12x 6x3mm round neodymium magnets
ASSEMBLY
Assembly is generally the same for both clamp types, other than the extra middle pieces for the triple clamp.
Superglue middle pieces
Install magnets with correct polarity (opposing)
Cut 180grit sandpaper with guide.stl and superglue onto sides and middle pieces
Slightly sand mating protrusions for smooth insertion
Install bottom hex bolt
Install shaft, lever & washer, thread the stopper (threading this thing can be a challenge, but it works). Future iterations of the stopper will have textured grip...meanwhile we will have to make do...use channel locks or clamps to turn this thing.
NOTE1: You may need the enlarge to hole on the shaft with an allan key or something to get the desired feel. Ideally, the shaft should be a little loose on the bolt. If its not, this won't affect the functionality but ideally, the lever is pushed up into fully open position solely by magnetic force. It's more of an ergonomics feature, if its important to you, you might need to tune that hole size a little.
NOTE2: The bolt requirements are not strict, if you find metric bolts (or whatever else) that are in the ball-park, it will probably work fine. Also, every hole can be enlarged by quite a bit with a set of Allen keys
With this remix I am also introducing a triple flying clamp (see Stringway clamps) for minimal tension loss due to drawback. Very useful for tie-offs.
PRINTING
It is important to note, that this design is intended for printing with carbon-fibre nylon, however I suspect ABS and PETG might work if all parts are printed at 90-100% density (lines). Recommended densities (%) are for CF nylon, 4 walls.
DOUBLE FLYING CLAMP
side_hexNut.stl -- 50%
side_noHexNut.stl --50%
2x middle_doubleClamp.stl --50%
shaft_doubleClamp --90%
lever.stl --90%
stopper.stl --90%
washer.stl --90%
guide.stl -- 50%
1/4 hex bolt 1.5 inch
1/4 lock nut
3/16 bolt 1 inch
8x 6x3mm round neodymium magnets
TRIPLE FLYING CLAMP
side_hexNut.stl -- 50%
side_noHexNut.stl --50%
2x middle_tripleClamp_outer.stl --50%
middle_tripleClamp_inner1.stl --50%
middle_tripleClamp_inner2.stl --50%
shaft_tripleClamp --90%
lever.stl --90%
stopper.stl --90%
washer.stl --90%
guide.stl -- 50%
1/4 hex bolt 2 inch (I didn't have one so there is an eye bolt in the image)
1/4 lock nut
3/16 bolt 1 inch
12x 6x3mm round neodymium magnets
ASSEMBLY
Assembly is generally the same for both clamp types, other than the extra middle pieces for the triple clamp.
Superglue middle pieces
Install magnets with correct polarity (opposing)
Cut 180grit sandpaper with guide.stl and superglue onto sides and middle pieces
Slightly sand mating protrusions for smooth insertion
Install bottom hex bolt
Install shaft, lever & washer, thread the stopper (threading this thing can be a challenge, but it works). Future iterations of the stopper will have textured grip...meanwhile we will have to make do...use channel locks or clamps to turn this thing.
NOTE1: You may need the enlarge to hole on the shaft with an allan key or something to get the desired feel. Ideally, the shaft should be a little loose on the bolt. If its not, this won't affect the functionality but ideally, the lever is pushed up into fully open position solely by magnetic force. It's more of an ergonomics feature, if its important to you, you might need to tune that hole size a little.
NOTE2: The bolt requirements are not strict, if you find metric bolts (or whatever else) that are in the ball-park, it will probably work fine. Also, every hole can be enlarged by quite a bit with a set of Allen keys
Similar models
thingiverse
free
wondershade 1/4 in bolt adaper square to hex bolt carriage bolt adapter by SevenCornersWorkshop
...by sevencornersworkshop
thingiverse
this adapts a 1/4 inch carriage bolt to fit in the hex cutout on the stands leg locking bolt
thingiverse
free
Flying Clamp for Tennis stringing IMPERIAL REMIX by sashalex007
...to cut your sandpaper.
usage:
these need to be clamped tight. if your clamp isn't holding tension, tighten the eyebolt more.
thingiverse
free
Celestron PowerSeeker 70EQ Dovetail Clamp by dkrnet
...ex head of the m6 x 70mm bolt is completely pressed into the hex-shaped recess
loosen the wing nut to permit attaching a dovetail
thingiverse
free
Shuriken magnet by grim86
...shuriken magnet by grim86
thingiverse
it needs a 6x3mm neodymium magnet.
thingiverse
free
Coupler, 5 mm to 1/4 inch, for Printrbot Simple All-Metal Z-Axis by Altan
... 4 pcs of 12 mm long m3 hex screws and nuts.
print conditions:
layer height: 0.1 mm
fill: 30%
wall thickness: 1 mm
brim: 20 mm
thingiverse
free
Refrigerator Magnet by hjelle
...ts-inch-cylinder-n48/dp/b001kv9raw/ref=sr_1_46?ie=utf8&qid=1394664231&sr=8-46&keywords=1%2f4+x+1%2f4+neodymium+magnet
thingiverse
free
Camera Mount 90 degree adapter by spudinator
...works with standard 1/4 - 20 unc threads found on most cameras, gopros, webcams.
use a 3/4 inch or 1 inch 1/4 - 20 bolt and nut.
thingiverse
free
1/4 inch compatible Minature Vice 2.0 by cyron52
...re:
the thingiverse post (doesn't have all the files)
the vice v2.0
the table clamp
hope this makes it easier for some folks.
thingiverse
free
Arlo Pro Camera Mount - boot compatible by ruarri
...ed by allowing the carriage bolt to protrude a little. the boots i have work just fine with the bolt pushed fully in its socket.
thingiverse
free
Kerfmaker for up to 7/8 inch dado using 1/4 inch hardware
...hing:2672696 for details of use.
requires:
print 1 top, 1 middle, 1 bottom and 2 knobs
2 1/4-20 x 3/4 hex bolts
2 1/4-20 hex nuts
Sashalex007
thingiverse
free
Skr 1.3 case-lid remix (for extra fan) by sashalex007
...ould repurpose it for better cooling for my drivers.
print the body from the original. https://www.thingiverse.com/thing:3688484
thingiverse
free
Elegoo Mars 2 filter & heater by sashalex007
...ilterbody.
super-glue the heater to heatermount.
super-glue the filtermount to the heatermount.
assemble filter (1/8x1/2 bolts)
thingiverse
free
Flying Clamp for Tennis stringing IMPERIAL REMIX by sashalex007
...to cut your sandpaper.
usage:
these need to be clamped tight. if your clamp isn't holding tension, tighten the eyebolt more.
thingiverse
free
Elegoo Mercury Plus - Magnetic Stirrer conversion by sashalex007
...he sensor-facing side.
video:https://www.reddit.com/r/elegoomars/comments/nz9r24/converted_my_mercury_into_a_magnetic_stirrer_uv/
thingiverse
free
Ender 5 Direct Drive linear rail mount
...speeddrive v1 - ender 3 direct drive mount by sashalex007 to fit ender 5 linear rails mod by...
thingiverse
free
SpeedDrive For TronXY Pro 2 by marcdraco
...by marcdraco thingiverse this is (yet another) remix of sashalex007#39;s rather super direct drive mod but this time for...
thingiverse
free
SpeedDrive v1 - Ender 3 direct drive mount remix for dual drive extruder
...a remix of the excellent direct drive update by sashalex007 to make it work with the cr-10s pro extruder....
thingiverse
free
SpeedDrive for E3D V6 + BMG extruder + Cable clip
...speeddrive v1 - ender 3 direct drive mount by sashalex007 (https://www.thingiverse.com/thing:3816051) speeddrive for e3d v6 + bmg extruder by...
thingiverse
free
Ender 3 Pro Chimera Mount for Fan Forced Air Convection by CrazyBucketMan
...crazybucketman thingiverse this is my remix of speeddrive by sashalex007 and the "ender 3 chimera aqua half direct mount"...
Tennis
thingiverse
free
tennis by mackenziegreen
...tennis by mackenziegreen
thingiverse
tennis
thingiverse
free
Tennis Racket by ninami
...tennis racket by ninami
thingiverse
tennis racket
thingiverse
free
Tennis Ball by ejpman
...tennis ball by ejpman
thingiverse
tennis ball
thingiverse
free
Tennis Keyring by schnixx
...tennis keyring by schnixx
thingiverse
tennis keyring
thingiverse
free
Lego tennis racket
...lego tennis racket
thingiverse
tennis racket lego compatible...
thingiverse
free
TENNIS COOKIE
...tennis cookie
thingiverse
print with petg
thingiverse
free
Tennis racquet bookmark by mortonnc
...tennis racquet bookmark by mortonnc
thingiverse
tennis racquet bookmark
thingiverse
free
Tennis Keychain by SazzyT
... and my last name on the bottom. there's also the ravens logo on it with a engraved tennis player who is about to hit a ball.
thingiverse
free
Keychain for Tennis Players by kekkoMaker
... of the nexto company to make easier playing tennis.
we have the student's box too.
we are the next, we are the nexto company
thingiverse
free
Tennis Ball by IconicDesign
...s ball by iconicdesign
thingiverse
playing around with 3d builder on windows 10 trying to make a tennis ball. hope you like it.
Stringing
thingiverse
free
String-base
...string-base
thingiverse
string-base
thingiverse
free
Stringing test
...stringing test
thingiverse
test for stringing and very small details
thingiverse
free
String Pull
...string pull
thingiverse
bathroom string pull 100% wall fill
thingiverse
free
String instrument
...g environments.
to amplify the sound of string instrument you can use plastic container.
enjoy your music with our string fab! :)
thingiverse
free
stringing test by KUZTM_3D
...stringing test by kuztm_3d
thingiverse
stringing test basic
thingiverse
free
Braile string by lees17
...braile string by lees17
thingiverse
braile string for frank ;)
thingiverse
free
String Spool by GiovaGio
...string spool by giovagio
thingiverse
spool for generic strings, wires, etc...
thingiverse
free
String Ship by Andrew_Keson
...erse
this is a very simple string fly ship. elevate one end of the string and watch the ship of your dreams soar!!!
enjoy!!!!
thingiverse
free
String Theory, a string library for OpenSCAD by 16807
...ity is exposed where ever there is a "regex" parameter flag in a method's signature, and of course, through grep().
thingiverse
free
String Release by MartinOberg
...string release by martinoberg
thingiverse
a simple string release for slingbows and regular bows.
Flying
thingiverse
free
Fly by Alajaz
...fly by alajaz
thingiverse
fly..
thingiverse
free
CIRCUS (not flying)
...circus (not flying)
thingiverse
circus (not flying)
thingiverse
free
Flying Scotsman
...flying scotsman
thingiverse
an updated version of the flying scotsman, as it is now running on the british mainline.
thingiverse
free
Fly base
...fly base thingiverse basic supports for showing flying creatures on your game...
thingiverse
free
fly killer by sarginson84
...fly killer by sarginson84
thingiverse
fly killer
thingiverse
free
the flying dutchman by Syzguru11
...the flying dutchman by syzguru11
thingiverse
the flying dutchman
thingiverse
free
fly / fliege by Syzguru11
...fly / fliege by syzguru11
thingiverse
fly fliege
thingiverse
free
DINO FLY by 3dplaymaker
...dino fly by 3dplaymaker
thingiverse
dino fly
thingiverse
free
flying dragon by schneck007
...flying dragon by schneck007
thingiverse
a flying dragon
thingiverse
free
flying disc by trloutz
...flying disc by trloutz
thingiverse
flying disc
Clamping
thingiverse
free
Clamp
...clamp
thingiverse
clamp
thingiverse
free
Clamp
...clamp
thingiverse
clamp for vacform
thingiverse
free
Clamp by bexer
...clamp by bexer
thingiverse
clamp, one clamp for many possibilities!
thingiverse
free
clamp by kimduckkyo
...clamp by kimduckkyo
thingiverse
clamp
thingiverse
free
clamp by glukofinder
...clamp by glukofinder
thingiverse
clamp
thingiverse
free
Clamp Chain
...clamp chain
thingiverse
this is a clamp
thingiverse
free
Clamp by wslab
...clamp by wslab
thingiverse
clamp
thingiverse
free
CLAMP by leonk
...clamp by leonk
thingiverse
clamp
thingiverse
free
Clamp by jkorinek87
...clamp by jkorinek87
thingiverse
clamp
thingiverse
free
Clamp by Emmanuelgnanasekar
...clamp model , it can be used for soft clamping ...
Clamp
thingiverse
free
Clamp
...clamp
thingiverse
clamp
thingiverse
free
Clamp
...clamp
thingiverse
clamp for vacform
thingiverse
free
Clamp by bexer
...clamp by bexer
thingiverse
clamp, one clamp for many possibilities!
thingiverse
free
clamp by kimduckkyo
...clamp by kimduckkyo
thingiverse
clamp
thingiverse
free
clamp by glukofinder
...clamp by glukofinder
thingiverse
clamp
thingiverse
free
Clamp Chain
...clamp chain
thingiverse
this is a clamp
thingiverse
free
Clamp by wslab
...clamp by wslab
thingiverse
clamp
thingiverse
free
CLAMP by leonk
...clamp by leonk
thingiverse
clamp
thingiverse
free
Clamp by jkorinek87
...clamp by jkorinek87
thingiverse
clamp
thingiverse
free
Clamp by Emmanuelgnanasekar
...clamp by emmanuelgnanasekar
thingiverse
this thing is a clamp model , it can be used for soft clamping things
Improved
thingiverse
free
improved by tacoking491
...improved by tacoking491
thingiverse
improved
thingiverse
free
Improved Improved e013 frame by Hammelhotdog
...it was inspired by the improved eachine e013 frame made by wladc, but has got some nice improvements by me
i hope you enjoy it :)
thingiverse
free
Rudder improved
...s mounted under engine / fishing / sailing ships and improves the steering properties considerably.
let the model be inspiration.
thingiverse
free
improved tensor by RicardoPina
...improved tensor by ricardopina
thingiverse
improved tensor
thingiverse
free
loox420 improved by chius
...loox420 improved by chius
thingiverse
case loox 420 improved
thingiverse
free
Improved Pins by Sideshaw
...improved pins by sideshaw
thingiverse
improved and working pins for micro gear heart keychain
thingiverse
free
Improved quality by adrybeach
...improved quality by adrybeach
thingiverse
improved quality for shell version. then printed at 200% size.
thingiverse
free
Improved enclosure by jnuz777
...improved enclosure by jnuz777
thingiverse
improved enclosure with 1 ab 22mm knock out on the lid.
thingiverse
free
Improved 787 Dreamliner
...improved 787 dreamliner
thingiverse
i improved the front and rear engine cowls and added turbofan blades.
thingiverse
free
45 deg improved slot with improved vent and bent resistance by Mariushod
...lot with improved vent and bent resistance by mariushod
thingiverse
i improved air flow and the bent resistance by adding a wall