Thingiverse
Flyduino Warthox 3D printed clone by hkazmi
by Thingiverse
Last crawled date: 3 years ago
Basically this is a small quad frame to look somewhat like a Flyduino Warthox.
http://flyduino.net/Quadrocopter-CF-Frame-Set-18cm-arm
I have the original too, interestingly, I pritned with 40% filling and 3 layers of wall top, down and parameter, it weighs less than half the original frame weight and is strong enough to fly nice and take on minor crashes. Though not as strong as the carbon fiber original.
Print this before ordering the original to see how your quad will fly, the orignal is 99 Euro, this is practically free.
Update: The original arms were 6mm thick just like the original warthox frame arm, but the printed ABS arm was flexible at this thickness, this caused the arms to bend/flex during flight and the control board would go crazy crashing the quad. The update has 12mm thick arms, these work great and by weight they are still the exact same weight (20g) at twice the thickness compared to the warthox frame arm, printed with 40% rectilinear fill.
Update 2: This has been flying amazing, much better than my DJI x450 frame based quad. With PI settings on KK2.0 board bumped to 100, its control is razor sharp.
http://flyduino.net/Quadrocopter-CF-Frame-Set-18cm-arm
I have the original too, interestingly, I pritned with 40% filling and 3 layers of wall top, down and parameter, it weighs less than half the original frame weight and is strong enough to fly nice and take on minor crashes. Though not as strong as the carbon fiber original.
Print this before ordering the original to see how your quad will fly, the orignal is 99 Euro, this is practically free.
Update: The original arms were 6mm thick just like the original warthox frame arm, but the printed ABS arm was flexible at this thickness, this caused the arms to bend/flex during flight and the control board would go crazy crashing the quad. The update has 12mm thick arms, these work great and by weight they are still the exact same weight (20g) at twice the thickness compared to the warthox frame arm, printed with 40% rectilinear fill.
Update 2: This has been flying amazing, much better than my DJI x450 frame based quad. With PI settings on KK2.0 board bumped to 100, its control is razor sharp.
Similar models
thingiverse
free
Warthox Gear Platform by Leo_N
...dded options like slots for velcro® fasteners, a notch for the gps cable and a holder for foam material to cover the baro sensor.
thingiverse
free
ZMR250 Motor Guard + Landing by bfboarder
...or the original zmr250 (3mm thick arms)!
feel free to change or update for later versions
updated version, less weight better fit
thingiverse
free
X95 MICRO QUAD FRAME (QX95 PARTS) UPDATED by boxermad84
...th only a 1 gram penalty over the original carbon frame but with more features!!
good luck and let me know it you have any ideas!
thingiverse
free
250 Acro Quadcopter by RobertCL
...d and broken something it's always been an arm, which is fairly quick and easy to replace without dismantling the whole quad.
thingiverse
free
Quadrocopter LiPo Holder for Warthox Frames by valid0r
...crews of the lower plate.
can be used together with gzebedin's awesome landing skit (http://www.thingiverse.com/thing:103143)
thingiverse
free
Quadrocopter landing skid for Flyduino warthox frame by gzebedin
...can adjust them :-)
printed with 0.4 infill and pla its 10g per leg. one can get it down to 6-7g i guess but for me this is ok.
thingiverse
free
quadcopter for 10 inch propellers made by plastic ABS except aluminum arms and metalic screws and nuts by noppita
...be install with apm pixhawk system and gopro or similar action camera with adjustable angle. the quad should be...
thingiverse
free
CIRCLE-CAT Standard 5mm by MarcRuhl
....
thickness: 5mm
flight controller: standard size, 36x36mm
print size: 200x200x5mm
weight: 140g
motor: 22xx
prop: up to 4.5"
thingiverse
free
remix mauler 5mm stronger arms
...o 4s and one arm broke flying. i reinforced arms but with a thickness of 5 mm.
my frame in pet carbon weighs 60 g with infill 70.
thingiverse
free
Diatone GT-M5 Fairing V2 by evret
...ith v2
also has a reinforced slot for a zip-tie because i like to have my rx antennas on the arms
printed in abs with 50% in-fill
Hkazmi
thingiverse
free
Camera Stabilizer for RC FPV by hkazmi
...i have a camera that comes with 1sq tiny quad copter mounted on my much bigger quad copter via this simple self level stabilizer.
thingiverse
free
Alternate fan mount for Budaschnozzle duct by hkazmi
...truder carriage. just clip it on to the carriage and screw in the duct to it,
works with http://www.thingiverse.com/thing:86875
thingiverse
free
Filament roll bearing, outter 31mm inner 8mm by hkazmi
...is with 0 infill and 2mm parameter and 2mm top and bottom. prints nicely.
make two of these, screw on to 8mm rod from each end.
thingiverse
free
Google Cardboard for Nexus 5 in a Spigen Neo Hybrid Case by hkazmi
...concept as its unlikely you will find the same binocular or have a nexus 5 in the exact same case as i do.
kids had a lot of fun.
thingiverse
free
Rctimer Crius AIOP v2.0 - UBLox CN-06 - bluetooth - HobbyKing 3dr radio all in one case by hkazmi
..., much cleaner.
rctimer aiop multiwii v2.0
rctimer ublox cn06 gps
rctimer multiwii bluetooth module
hobbyking 3dr module.
Warthox
thingiverse
free
Warthox GR-16 Mount by Leo_N
...the warthox frame.
it is designed to the hold the graupner gr-16 receiver by means of a zip tie (2.5mm wide) in place.
enjoy,
leo
thingiverse
free
Warthox Center Plates 600TVL Cam Holder by Rangarid
... plates 600tvl cam holder by rangarid
thingiverse
can be zip tied to the warthox center plates when using 10mm aluminium pofile.
thingiverse
free
Warthox Center Plates 600TVL Cam Holder by Rangarid
... plates 600tvl cam holder by rangarid
thingiverse
can be zip tied to the warthox center plates when using 10mm aluminium pofile.
thingiverse
free
Warthox Gear Platform by Leo_N
...dded options like slots for velcro® fasteners, a notch for the gps cable and a holder for foam material to cover the baro sensor.
thingiverse
free
Warthox GPS Mount by Leo_N
...ective-shell-for-pix-px4-pixhawk-p-1005394.html
the module is easily held in place by simply snapping it on the mount.
enjoy,
leo
thingiverse
free
Quadrocopter LiPo Holder for Warthox Frames by valid0r
...crews of the lower plate.
can be used together with gzebedin's awesome landing skit (http://www.thingiverse.com/thing:103143)
thingiverse
free
Warthox Lipo Protection Plate by Leo_N
...te to protect the lipo from getting damaged by the protruding frame screws.
part printed in pla weighs aprox. 7 grams.
enjoy,
leo
thingiverse
free
Warthox Landing Skid by Leo_N
...for a nicer appearance and i also added holding tabs for the receiver antennas.
printed in pla each leg weighs 7 gram.
enjoy,
leo
thingiverse
free
MAVLink-OSD Holder (Warthox) by Leo_N
... if necessary or you what new features to the design.
also please post a picture with comments if you have made one.
thanks.
leo
Flyduino
thingiverse
free
protection cap "simple" for flyduino 15x8 arms by maulwurfpauli
...ion cap "simple" for flyduino 15x8 arms by maulwurfpauli
thingiverse
protection cap for flyduino 15x8mm aluminium arms
thingiverse
free
protection cap "bumper" for flyduino 15x8 arms by maulwurfpauli
...ion cap "bumper" for flyduino 15x8 arms by maulwurfpauli
thingiverse
protection cap for flyduino 15x8mm aluminium arms
thingiverse
free
protection cap "bumper light" for flyduino 15x8 arms by maulwurfpauli
...p "bumper light" for flyduino 15x8 arms by maulwurfpauli
thingiverse
protection cap for flyduino 15x8mm aluminium arms
thingiverse
free
#Flyduino FCP Motormount (black) by axelnied
...ount (black) by axelnied
thingiverse
this thing was made with tinkercad. edit it online https://tinkercad.com/things/fk2bfbdux1c
thingiverse
free
Flyduino KISS ESC PDB spacer/insulator by Painless360
...ctive frame materials) and ensure that non of the small contacts underneath touch the frame.
thanks for looking, happy printing!
thingiverse
free
Eyefly Trip - Case for the flyduino 12A & 18A KISS ESC by svthomsen
...vthomsen
thingiverse
just a case for the 12a & 18a kiss esc from flyduino.net to mount the esc nicely on the existing holes.
thingiverse
free
Quadrocopter landing skid for Flyduino warthox frame by gzebedin
...can adjust them :-)
printed with 0.4 infill and pla its 10g per leg. one can get it down to 6-7g i guess but for me this is ok.
thingiverse
free
ZMR-X 210 Runcam Skyplus Camholder by x4FF3
...this is a simple camholder with space for the flyduino micro minimosd. it fits the runcam skyplus, which has...
thingiverse
free
Mini Honeycomb Quadcopter - 18cm version by vincpad
...my 180x180mm printing capacity. holes are provided for the flyduino nanowii fc and turnigy multistar 1704-1900kv...
Clone
3d_export
$5
Clones great republic
...clones great republic
3dexport
clones great republic.those same clones from the star wars movie universe.4 clones available.
3d_export
$10
Clone 3D Model
...clone 3d model
3dexport
clone woman girl female lady chamber sci fi
clone 3d model calcm1 51695 3dexport
turbosquid
$5
Clone machine
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
archive3d
free
Clone trooper 3D Model
...nd army soldier trooper
clone trooper 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
free
Lego Clone Walker
...ree 3d model lego sw clone walker for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1292252)
turbosquid
$15
Clone trooper helmet
...d model clone trooper helmet for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1199355)
archive3d
free
Clone trooper 3D Model
...and army soldier trooper
clonetrooper 3 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archive3d
free
Clone trooper 3D Model
...and army soldier trooper
clonetrooper 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_ocean
$35
Surface Clone C4D materials
...+ of the most well made materials for maxon’s cinema 4d; on the internet today. each material is crafted with a specific purpo...
turbosquid
$3
Sci-fi cloning vats
...cloning vats for download as 3ds, obj, wrl, x, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1290168)
Printed
design_connected
$27
...print
designconnected
moroso print computer generated 3d model. designed by wanders, marcel.
3ddd
free
Eichholtz Prints
...- eichholtz print central station i
13 - eichholtz print central station ii
14 - eichholtz print marisa
15 - eichholtz print tish
3ddd
$1
Eichholtz Prints
...print abstract - set of 2
10 - eichholtz print orange abstract
11 - eichholtz print buddha right
12 - eichholtz print buddha left
turbosquid
$1
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
free
Eichholtz Prints
...of 4
2 - print dunbar 2 set of 4
3 - print guadeloupe 1 set of 4
4 - print guadeloupe 2 set of 4
5 - print giles
6 - print trett
3ddd
$1
Eichholtz Prints
...nt tutti frutti
3 - eichholtz prints watson - set of 2
4 - eichholtz prints antique nautilus - set of 2
5 - eichholtz print tiara
3d_export
$5
Monster for printing
...monster for printing
3dexport
monster 3d model printing
3ddd
free
printed rug
...printed rug
3ddd
ковер
very creative printed rug
3ddd
free
Eichholtz Prints
...иал: бумага
габариты (вхш): 72 x 62 см
описание: print sweetmeat - постер в деревянной раме.
3 - prints varsity set of 2
арти
3ddd
free
Art Print Posters
...art print posters
3ddd
прованс
art print posters by patrician prints