Thingiverse
FlashForge Creator & Pro Connectors by agilliam
by Thingiverse
Last crawled date: 3 years ago
I decided to do this write-up, since i have seen a lot of people asking what connectors are for certain electronics on the FFC and FFCP. I am in the process of converting my printers wiring from the cheap china to a good quality silicone wire. I have read too many printers that have caught fire due to wires breaking and causing high resistance connecions, or flat out shorting out. Here is the list of 100% verified connectors. I ordered them and have them in hand and have tested each one!
5x Stepper Motor PHR-6 6 POSITION PH SERIES 2MM SPACING DIGIKEY # 455-1162-ND
20x Crimp Connectors for above housing 22AWG - 24AWG DIGIKEY # WM2510CT-ND
5x Stepper Motor to MighjtyBoard (KIT) 4P KK-156 Series DIGIKEY # WMLX-203
1x Heated Build Plate POWER Housing 2 pin DIGIKEY # 1744036-2-SI-ND
2x Heated Build Plate Crimps for above housings 18AWG-22AWG DIGIKEY # 1123721 -2
1x Heated build plate sensor are XH 4p 2.5mm DIGIKEY # 455-02267-ND
4x Crimp/Contacts for above XH Connectors 22AWG - 28AWG DIGIKEY #455-1135-2-ND
3x Fan Connectors at Extruder carriage XH 2.5mm 2 pin plug DIGIKEY # 455-2266-ND
6x Crimp/Contacts XH 455-1135-2-ND
3x Fan Socket (coming from MightyBoard XH 2.5mm 2 pin socket DIGIKEY # 455-2247-ND
7x Limit Switches and HBP Sensor to MB (These have latch) 4 P DIGIKEY # WM2902-ND
28x Crimps for above connector housings 24AWG - 28AWG DIGIKEY # 455-2148-1-ND
Heated Bed / Thermocouples / Extruder Heaters / Fans
ALL are 2 pin DIGIKEY # ED2779-ND You can get in BLACK or GREEN
If you use or replace their 2 pin green / black connectors you will need
7x Green 2 pin connectors like above
3x Black 2 pin connectors like above.
OR
The single 4 pin connectors are DIGIKEY# ED2781-ND
You would need
2x 1 for each extruder/fan pair maintaining the correct polarity and allowing for D/C
1x for thermocouple pair also allowing D/C but maintaining polarity.
Then you would only need 4x 2 pin like the original ones.
I suggest changing the green/black connectors, as they are very loose tolerances. I bought a good quality name brand from my local electronics shop and they are TIGHT.
This is why you see so many pictures of burned connectors on the FFCP main boards. Loose connections = high resistance connections resulting in fire or burned connectors!
it would work as a 350W. I dont trust china's quality control.
If I have missed something or have any questions please contact me. Hope this helps someone else out there.
5x Stepper Motor PHR-6 6 POSITION PH SERIES 2MM SPACING DIGIKEY # 455-1162-ND
20x Crimp Connectors for above housing 22AWG - 24AWG DIGIKEY # WM2510CT-ND
5x Stepper Motor to MighjtyBoard (KIT) 4P KK-156 Series DIGIKEY # WMLX-203
1x Heated Build Plate POWER Housing 2 pin DIGIKEY # 1744036-2-SI-ND
2x Heated Build Plate Crimps for above housings 18AWG-22AWG DIGIKEY # 1123721 -2
1x Heated build plate sensor are XH 4p 2.5mm DIGIKEY # 455-02267-ND
4x Crimp/Contacts for above XH Connectors 22AWG - 28AWG DIGIKEY #455-1135-2-ND
3x Fan Connectors at Extruder carriage XH 2.5mm 2 pin plug DIGIKEY # 455-2266-ND
6x Crimp/Contacts XH 455-1135-2-ND
3x Fan Socket (coming from MightyBoard XH 2.5mm 2 pin socket DIGIKEY # 455-2247-ND
7x Limit Switches and HBP Sensor to MB (These have latch) 4 P DIGIKEY # WM2902-ND
28x Crimps for above connector housings 24AWG - 28AWG DIGIKEY # 455-2148-1-ND
Heated Bed / Thermocouples / Extruder Heaters / Fans
ALL are 2 pin DIGIKEY # ED2779-ND You can get in BLACK or GREEN
If you use or replace their 2 pin green / black connectors you will need
7x Green 2 pin connectors like above
3x Black 2 pin connectors like above.
OR
The single 4 pin connectors are DIGIKEY# ED2781-ND
You would need
2x 1 for each extruder/fan pair maintaining the correct polarity and allowing for D/C
1x for thermocouple pair also allowing D/C but maintaining polarity.
Then you would only need 4x 2 pin like the original ones.
I suggest changing the green/black connectors, as they are very loose tolerances. I bought a good quality name brand from my local electronics shop and they are TIGHT.
This is why you see so many pictures of burned connectors on the FFCP main boards. Loose connections = high resistance connections resulting in fire or burned connectors!
it would work as a 350W. I dont trust china's quality control.
If I have missed something or have any questions please contact me. Hope this helps someone else out there.
Similar models
thingiverse
free
Replicator 2X Heated Platform Extension Cable by Jake
...t you're doing before you install this. i have not yet installed mine yet. your mileage my vary. proceed at your own risk.
thingiverse
free
Titan Extruder mount for Lulzbot Taz 6 with E3D V6 Hotend by StephS
... housing (digikey pn: wm2525-nd)
20x male crimp connectors (digikey pn: wm2517-nd)
misc m3 screws for fan mounting.
printed parts
grabcad
free
2-Pin JST XH - Right Angle Connector Pinheader white 2.5mm
...2-pin jst xh - right angle connector pinheader white 2.5mm
grabcad
2-pin jst xh - right angle connector pinheader white 2.5mm
thingiverse
free
Orion Fan Upgrade for Replicator 2X by Jake
...0
455-2261-1-nd conn term crimp xh 26-30awg - might as well get 20 or more so when you screw up one you have more to try again.
grabcad
free
XH connectors
...rametric models for kompas-3d
ps see https://grabcad.com/library/xhp-connectors-1 (female housing with crimped terminals for xh)
grabcad
free
JST-XH_SMD_VERTICAL 2.5mm (Generic) Connectors
...cal 2.5mm smd generic connectors (2-pin, 3-pin, 4-pin, 5-pin, 6-pin, 7-pin, and 8-pin). step files and pcb foot print dimensions.
thingiverse
free
PRINT SMOOTHER AKA TL_SMOOTHER SMD by agilliam
...re a double layer clad pcb i prefer personally smd for simplicity.
i am dealing with a death in the family so it may be a while!
grabcad
free
JST-xH 7pin 2.5mm
...jst-xh 7pin 2.5mm
grabcad
jst-xh pin header with 2.5mm pin spacing
thingiverse
free
Male JST-XH 2-Pin to Jumper by swimgod
...male jst-xh 2-pin to jumper by swimgod
thingiverse
male 2 pin jst-xh socket with breadboard jumper pins.
2.5mm pitch
grabcad
free
XHP connectors
...0.6) for https://grabcad.com/library/xh-connectors-1 - 2.5mm pitch
.step models 1-16,20 pins
.m3d parametric models for kompas-3d
Agilliam
thingiverse
free
Heart Box by agilliam
...ut, my daughter saw it and wanted one, so i used the same design but put a my little pony on it. see my other "things".
thingiverse
free
Clock Winding Key by agilliam
...t this way.
if you need one with larger holes for different sized clocks, let me know ill be more than happy to accommodate them!
thingiverse
free
FFCP 2016 Build Plate Harness Plug by agilliam
...el where they made the hole smaller.
this prevents junk from falling underneath and causing overheating and clogging fans.
enjoy!
thingiverse
free
Heart shaped box with My Little Pony by agilliam
...t. i got the mlp image from sketchup and cocked it at an slight angle and slices it. placed it ontop of the lid giving a 3d look.
thingiverse
free
Traxxas Nitro Hawk Parts by agilliam
...cided to make servo mounts, etc. i hope to try to make everything plastic, and put on here even gear box... a personal challenge.
thingiverse
free
FFCP FlashForge Creator Pro Filament Guide by agilliam
...the tube, i don't care for the black stuff flashforge gives you)
no support nor raft needed, very easy and straight forward.
thingiverse
free
FlashForge Build Plate Harness Plug by agilliam
...tuff dropping inside!
you may need to file just a bit if your printer isn't calibrated highly like this one. its a tight fit!
thingiverse
free
FlashForge Creator Pro Wire Plug/Retainer by agilliam
...o the wire cavity to help hold the wires into place.
still learning sketchup! i'm used to autocad, but this is way different!
thingiverse
free
Croquet Malet Pad by agilliam
...s a no brand name croquet set, i think they are standard though from what i can remember when i was a child and played with them.
thingiverse
free
DashCam T slot adapter to Garmin by agilliam
...ints fine it nylon, abs, and pla. with nylon and abs you will need rafts as there is a very small surface for contact on the rim.
Flashforge
thingiverse
free
Flashforge Logo
...flashforge logo
thingiverse
flashforge logo
thingiverse
free
flashforge logo by morive3d
...flashforge logo by morive3d
thingiverse
this is a flashforge stamphttps://www.youtube.com/channel/ucu6ge9qrju9cpgg6wrlxkqw
thingiverse
free
Flashforge Glass Bed by olo2000pm
...flashforge glass bed by olo2000pm
thingiverse
flashforge glass bed
thingiverse
free
Toolbox for FlashForge Finder by Gringo1970
...toolbox for flashforge finder by gringo1970
thingiverse
smal toolbox for flashforge finder
thingiverse
free
Flashforge / Dremel lid by Disco_Rob
...flashforge / dremel lid by disco_rob
thingiverse
lid extension for the flashforge dreamer
thingiverse
free
Flashforge Dreamer Filamentguide by PeterS1
...de for flashforge dreamer / dremel idea. you need also flashforge dreamer lid spacer (http://www.thingiverse.com/thing:1219953)
thingiverse
free
Flashforge creator legs by cybadigitals
...flashforge creator legs by cybadigitals
thingiverse
these legs gives a clearance of 25mm for flashforge creator series
thingiverse
free
Flashforge Inventor/Dreamer by Iprintr7
...orge inventor/dreamer by iprintr7
thingiverse
this is my first thingiverse project and is a model of the flashforge 3d printer
thingiverse
free
Flashforge Filiment Guide by russellscanlan
...flashforge filiment guide by russellscanlan
thingiverse
my design to feed filament through the door on a flashforge adventure 3
thingiverse
free
Flashforge Winder Adapter by newky2k
...winder adapter by newky2k
thingiverse
adapters for the flashforge 0.5 kg spools to the for the filament spool winder by ssinnott
Creator
3ddd
$1
CREATOR
... молдавия
круглая кровать молдавской мастерской creator.диаметр спального места - 1900мм,материалы настроены.
turbosquid
$75
Creators Realm
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
LEGO Creator Part 2
...
lego , конструктор , машина
lego creator №6753
turbosquid
free
Game Creator Pack
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
LEGO Creator №6753 Part 3
...
lego , конструктор , машина
lego creator №6753
3ddd
$1
LEGO Creator №6753 Part 1
...
lego , конструктор , машина
lego creator №6753
turbosquid
$29
Train Track Creator Pro
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$39
Train Track Creator Pro
...n tracks, for video game or rendering in a matter of minutes. all the models in this pack are low poly with high resolution te...
turbosquid
$7
FPS Creator Reloaded Rock Pack 1
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Декоративные элементы BV Decor CREATOR III часть
...ментов и декорирования стен.
множество вариантов для вашей фантазии.https://bvdecor.com/es/category/list/cat/creator-es
Connectors
turbosquid
$5
Connector
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
Connector
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Connector 3D Model
...connector 3d model
3dexport
connector штекер 3d
connector 3d model manch111 83121 3dexport
3d_export
$14
connector production equipment
...connector production equipment
3dexport
connector production equipment
3d_export
$10
connector xt60
...e designing, and will help save your precious time. the scale of the model is 1:1. the dimensions are for reference in the image.
turbosquid
free
Audio connectors
...del audio connectors for download as obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1424706)
3d_export
$20
car connectors dj70
...quot; connector 9-pin "dj7091a-2.8-11/21" terminal (male) "dj611-2.8" terminal (female) "dj622-2.8"
turbosquid
$30
Cinch connector
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
Jumper Connector
...umper connector for download as 3ds, obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1494917)
turbosquid
$15
RCA Connector
...l rca connector for download as 3ds, obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1376648)
Pro
turbosquid
$29
Pro
...ree 3d model mac pro for download as obj, c4d, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1505782)
turbosquid
$15
Apple Mac Pro and Pro Display
...ee 3d model apple mac pro and pro display for download as max on turbosquid: 3d models for games, architecture, videos. (1417078)
3d_export
$5
iphone 13 pro max and pro
...3 pro max and 13 pro the model is made in four colors (graphite, gold, silver, and blue), all of which are attached in the files.
3d_export
free
sapphire pro
...sapphire pro
3dexport
sapphire pro 3d printer head mask
3d_export
$4
macbook pro
...macbook pro
3dexport
macbook pro 13" inch 2020 years model
3ddd
free
GentleLase Pro
... syneron , candela
gentlelase pro аппарат для лазерной эпиляции
turbosquid
$25
PRO frame
...rbosquid
royalty free 3d model pro frame for download as max on turbosquid: 3d models for games, architecture, videos. (1148329)
turbosquid
$5
Alien pro
...osquid
royalty free 3d model alien pro for download as blend on turbosquid: 3d models for games, architecture, videos. (1678446)
turbosquid
$5
iphone11 pro
...uid
royalty free 3d model iphone11 pro for download as blend on turbosquid: 3d models for games, architecture, videos. (1562707)
3ddd
$1
Mac Pro (appel)
...mac pro (appel)
3ddd
компьютер , apple
mac pro