Thingiverse
![FireStorm Wheel by Martinrome](/previews/8603168.jpg)
FireStorm Wheel by Martinrome
by Thingiverse
Last crawled date: 3 years, 1 month ago
My FireStorm is a great kit, but the small wheels make it difficult to land in grass. I designed these wheels to replace those. They are a little heavier, but the model can easily handle the weight and it helps by adding a little more nose weight (which it needs). I used clear vinyl tubing (1/4 inch ID, 3/8 inch OD) for the tire and connected the ends with the included connector and some CA glue.
Similar models
thingiverse
free
![GoPro Session dummy by MH_FPV](/t/8786851.jpg)
GoPro Session dummy by MH_FPV
...ere you can add some little weights to have the same weight as a original gopro session. i used weights for balancing car wheels.
thingiverse
free
![Knuckle Tungsten Weight Holder by danielanguita](/t/9249964.jpg)
Knuckle Tungsten Weight Holder by danielanguita
...eads for weight holders (found on ebay, etc)
must use 2.2 wheels with inner rings with a bigger diameter of 64.5 mm (2.55 inches)
thingiverse
free
![RC Plane Wheel (Demoiselle) by Karlex](/t/8853668.jpg)
RC Plane Wheel (Demoiselle) by Karlex
...lane has a wingspan of 1.60m and weights 1250g.
check out the videos at: https://www.youtube.com/channel/uceyztqahsr7xrfrye5pg-ig
thingiverse
free
![Wall mount for 3 inch wheels](/t/4919502.jpg)
Wall mount for 3 inch wheels
...ized to fit. then i discovered that the wire for the wheel hug was hitting the edge of the mount, so i cut a hole in the design.
thingiverse
free
![HPI Firestorm Batteriehalter GoPro Mount by Hackbert](/t/8745631.jpg)
HPI Firestorm Batteriehalter GoPro Mount by Hackbert
...hpi firestorm batteriehalter gopro mount by hackbert
thingiverse
hpi firestorm batteriehalter gopro mount
thingiverse
free
![Epic 40K Firestorm Redoubt by BiancaW](/t/8698813.jpg)
Epic 40K Firestorm Redoubt by BiancaW
...epic 40k firestorm redoubt by biancaw
thingiverse
6mm scale version of the gw firestorm redoubt for epic 40k
thingiverse
free
![Simple wheel by John35588](/t/8532857.jpg)
Simple wheel by John35588
...simple wheel by john35588
thingiverse
just a little wheel i made for a mini trash can.
thingiverse
free
![4-inch Wheel by dkathan](/t/8899199.jpg)
4-inch Wheel by dkathan
...e. this makes the object easier to print.
you may need to rotate the object for your slicer so that it lays flat on the bed.
thingiverse
free
![Hamster Wheel by TomFromSpace](/t/5032929.jpg)
Hamster Wheel by TomFromSpace
... too small, so this one is a bit bigger at a little less than 8 inches across. it spins well and has held up to a lot of running.
thingiverse
free
![Koso speedometer housing + Honda VTR FIRESTORM bracket by brandbull](/t/5023471.jpg)
Koso speedometer housing + Honda VTR FIRESTORM bracket by brandbull
...peedometer housing + honda vtr firestorm bracket by brandbull
thingiverse
koso speedometer housing + honda vtr firestorm bracket
Martinrome
thingiverse
free
![Simple Clock by Martinrome](/t/8777383.jpg)
Simple Clock by Martinrome
...cided to design a simple one. the movement is from klockit.com. the numbers need to be printed face down. i used a raft for them.
thingiverse
free
![PS3 Controller Holder by Martinrome](/t/8603164.jpg)
PS3 Controller Holder by Martinrome
...or the grandkids. i wanted something light and small. decided to design one. this prints best on its side with supports and raft.
thingiverse
free
![Bat105 Propeller Guard by Martinrome](/t/8704370.jpg)
Bat105 Propeller Guard by Martinrome
...i designed more robust ones. these weigh 1/2 gram each more than the originals but i think they are worth a little bit of weight.
thingiverse
free
![QX105 Antenna Shield by Martinrome](/t/8729558.jpg)
QX105 Antenna Shield by Martinrome
...e screws that are already holding down the top plate. they are long enough to accommodate this part. i used a raft to print this.
thingiverse
free
![Gimbal Sticks by Martinrome](/t/8045578.jpg)
Gimbal Sticks by Martinrome
...t them together.
edit: i added some shorter sticks and a plain top. i like the short stick and plain top, but that's just me.
thingiverse
free
![Frsky XM Plus Case by Martinrome](/t/8684788.jpg)
Frsky XM Plus Case by Martinrome
...ht-angle pins. it fits well, but i used a drop of ca on one of the edges. you can still get to the bind button and antenna leads.
thingiverse
free
![Omnibus Flight Controller Case by Martinrome](/t/8714081.jpg)
Omnibus Flight Controller Case by Martinrome
... and needed a simple case i could mount with double-sided tape. there are two covers depending on what type of pins you install.
thingiverse
free
![Flite Test Minimotor Mount by Martinrome](/t/8776145.jpg)
Flite Test Minimotor Mount by Martinrome
...motor mount and small pod. i just hand drilled the side holes after printing with a 1/8 bit to male them fit the skewers exactly.
thingiverse
free
![QX90 Robust Camera Mount by Martinrome](/t/8759681.jpg)
QX90 Robust Camera Mount by Martinrome
...dy posted. this one is a little heavier, but i didn't notice any difference in flying. the prop guards are from plainless360.
Firestorm
thingiverse
free
![Epic 40K Firestorm Redoubt by BiancaW](/t/8698813.jpg)
Epic 40K Firestorm Redoubt by BiancaW
...epic 40k firestorm redoubt by biancaw
thingiverse
6mm scale version of the gw firestorm redoubt for epic 40k
thingiverse
free
![HPI Firestorm Batteriehalter GoPro Mount by Hackbert](/t/8745631.jpg)
HPI Firestorm Batteriehalter GoPro Mount by Hackbert
...hpi firestorm batteriehalter gopro mount by hackbert
thingiverse
hpi firestorm batteriehalter gopro mount
thingiverse
free
![Imperial Firestorm Resized (Italianmoose)](/t/4976754.jpg)
Imperial Firestorm Resized (Italianmoose)
...rence and resized the prow lance as well as shortened the prow some. that's about it. italianmoose's design is fantastic.
thingiverse
free
![Black & Decker Firestorm Router Base Plate by AlfaGolfTango](/t/8304081.jpg)
Black & Decker Firestorm Router Base Plate by AlfaGolfTango
...restorm router base plate by alfagolftango
thingiverse
replacement base plate for black and decker firestorm router (fs1000rp) .
thingiverse
free
![Koso speedometer housing + Honda VTR FIRESTORM bracket by brandbull](/t/5023471.jpg)
Koso speedometer housing + Honda VTR FIRESTORM bracket by brandbull
...peedometer housing + honda vtr firestorm bracket by brandbull
thingiverse
koso speedometer housing + honda vtr firestorm bracket
thingiverse
free
![firestorm turret - space elf promo model by jimjimjimmyjim](/t/8137325.jpg)
firestorm turret - space elf promo model by jimjimjimmyjim
...yjim
thingiverse
firestorm turret - space elf promo model
find the space elf flying tanks armada here:
patreon.com/xyyminiatures
thingiverse
free
![Firestorm Quantum Splicer](/t/4911461.jpg)
Firestorm Quantum Splicer
...m printer.
on rest of the arm there are holes for mini brooch back bars pins so you can easy attache the device to your t-shirt.
thingiverse
free
![HPI E-Firestorm battery plate by Landin81](/t/8862030.jpg)
HPI E-Firestorm battery plate by Landin81
...irestorm battery plate by landin81
thingiverse
made a batteryplate for my friends car. it will fit for a 5000mah 3s 30c battery.
thingiverse
free
![Black and Decker 18V Firestorm Battery by drewk538](/t/8542335.jpg)
Black and Decker 18V Firestorm Battery by drewk538
...upport material in the design. you can delete it if you wish and use your slicing software to do the support material. good luck
Wheel
thingiverse
free
![power wheels wheels](/t/4765082.jpg)
power wheels wheels
...power wheels wheels
thingiverse
wheel for a power wheels 9 inches in diameter
thingiverse
free
![wheel](/t/4704025.jpg)
wheel
...wheel
thingiverse
wheel
thingiverse
free
![wheel](/t/4705545.jpg)
wheel
...wheel
thingiverse
wheel
thingiverse
free
![The Wheel, Wheel by duemosy](/t/9241952.jpg)
The Wheel, Wheel by duemosy
...iverse
wheel wheel for maker's muse design challenge
the scaling is a little weird, had to scale to 50% for it to look right
thingiverse
free
![wheel](/t/4904714.jpg)
wheel
...wheel
thingiverse
wheel thingi
thingiverse
free
![Wheel](/t/4894910.jpg)
Wheel
...wheel
thingiverse
wheel made in fusion360
thingiverse
free
![Wheel](/t/4773556.jpg)
Wheel
...wheel
thingiverse
wheel of toy car
thingiverse
free
![wheel](/t/4972180.jpg)
wheel
...wheel
thingiverse
toy car wheel
thingiverse
free
![Wheel](/t/4838326.jpg)
Wheel
...wheel
thingiverse
some wheel model.
thingiverse
free
![Wheels, wheels, wheels by IronOxide](/t/8888822.jpg)
Wheels, wheels, wheels by IronOxide
...width is limited
only one spoke style
round axle is the only option at this time
code thrown together quickly - not the prettiest