Thingiverse
FilamentSpool bearingTable by masterwoz
by Thingiverse
Last crawled date: 3 years ago
I aimed at the spool table where a filament spool with the various sizes can be set easily.
A revolution in a spool table goes around lightly by 1 BB ball.
A filament is supplied smoothly by letting a hole of a coin which has a hole like a 5 yen coin and a 50 yen coin through.
A coin is to change according to the top and the bottom, and slack of a filament also disappears.
Please prepare 1 coin with a hole like 5 yen coin and 50 yen coin.
Please prepare 1 BB ball of an air soft gun.
A revolution in a spool table goes around lightly by 1 BB ball.
A filament is supplied smoothly by letting a hole of a coin which has a hole like a 5 yen coin and a 50 yen coin through.
A coin is to change according to the top and the bottom, and slack of a filament also disappears.
Please prepare 1 coin with a hole like 5 yen coin and 50 yen coin.
Please prepare 1 BB ball of an air soft gun.
Similar models
thingiverse
free
10 Yen copper coin (or 50 sen phoenix silver coin) finger spinner 608ver, by jin0711
...8 ball bearing
"japaniese 10 yen copper coin " and " jananies 50 sen phoenix silver coin" is same size! yeah!
3dwarehouse
free
yen coin is:printable
...yen coin is:printable
3dwarehouse
japanese 5 yen coin. only one side done #coin #isprintable #japanese #money #yen
thingiverse
free
2020 Spool holder (otional 4mm BB's) by webnick
... webnick
thingiverse
just another spool holder for 750gr filament spool
there is room for some 4mm bb balls to decrease friction
thingiverse
free
Filament Spool Rotation Holder by miscellany
...hingiverse
filament spool rotation holder for snapmaker 3d printer.
but you can use it anywhere.
i used 6mm bb for ball bearing.
cg_trader
$2
Japan 500 yen coin - set - vol 5
...set - vol 5
cg trader
3d japan 500 yen coin - set - vol 5 coin coins coin-set, available in blend, ready for 3d animation and ot
thingiverse
free
Filament spool shaft ball bearing support (Samla project) by pattarom
...bic pla that have a hole of 58mm, so i draw an adapter. this one is slightly conical externally, so it will fit from 56 to 59 mm.
thingiverse
free
Filament Spool Holder by Mr_Vigil
... nuts and bolts
spool hole size 32 to 72 mm [1.25 to 2.83 in]
material: pla
time: 5:56
infill: 20%
ext temp: 210 c
bed temp: 50 c
thingiverse
free
Filament Spool Rotating Holder by miscellany
... spool rotating holder for snapmaker 2.0 series.
but you can use it anywhere.
i used airsoft gun 6mm bb bullets for ball bearing.
thingiverse
free
Filament spool holder by GrimalKin
...y grimalkin
thingiverse
a filament spool holder
need 2 roller ball bearings and a threaded rod of 8mm, 2washers
pla 210°
50 mm/s
thingiverse
free
Coin bank for the 1, 5, 10, and 50 coins by SevenCornersWorkshop
...oin bank for the 1, 5, 10, and 50 coins by sevencornersworkshop
thingiverse
a coin bank to hold 25 $1, 13 $5, 25 $10, and 13 $50
Masterwoz
thingiverse
free
KODAMA TRINUS filament guide by masterwoz
... it was small in size it rotated inside and it was difficult to enter the filament, so we increased the size so as not to rotate.
thingiverse
free
Gear Puller V2 by masterwoz
...アゴの厚みでステッピングモーターの本体とピニオンギアの隙間に合わせて出来るだけ厚い方で作業するのが良いと思います。
他に必要なものはm4*25mm〜30mmくらいのネジです。
私は手で回せるように蝶ナットの付いたネジを使いましたが、手持ちのもので大丈夫です。
thingiverse
free
singleBB_bearing-series_Spool_Holder by masterwoz
...ラをセットしてスライドレールで連結すれば完成です。
(お使いのスプールの幅に合わせてご利用ください)
ローラーのフランジは小口径と大口径がありますが、大口径の方を外側になるようにセットしてください。
※ エアガン用のbb弾(直径6mm)を8個が別に必要です。
thingiverse
free
M3 Screw Cap by masterwoz
...0mm/s
fillpattern:concentric
infill:100%
rafts:yes
supports:no
single outline corkscrew mode:no
filament : i use pla 1.75mm
thingiverse
free
Filament guide with oiler by masterwoz
...30mm/s
fillpattern:concentric
infill:25%
rafts:yes
supports:no
single outline corkscrew mode:no
filament : i use pla 1.75mm
thingiverse
free
Plastic cardboard Enclosure / KODAMA TRINUS by masterwoz
...mm/s
fillpattern:rectilinear
infill:40%
rafts:yes
supports:yes
single outline corkscrew mode:no
filament : i use abs 1.75mm
thingiverse
free
Extruder mounting Plate with adjustable height by masterwoz
...m/s
fillpattern:rectilinear
infill:100%
rafts:yes
supports:yes
single outline corkscrew mode:no
filament : i use pla 1.75mm
thingiverse
free
Extruder mounting Plate with adjustable height ver.2 by masterwoz
...m/s
fillpattern:rectilinear
infill:100%
rafts:yes
supports:yes
single outline corkscrew mode:no
filament : i use abs 1.75mm
Filamentspool
thingiverse
free
Another filamentspool by Gorz
...his filament spool on the same core but i created a much more slender side structure to it! less material, lower production cost.
thingiverse
free
Filamentspool holder by Modellaner
...:
4 x 608z bearrings
4 x m8 nuts
4 x m8 washers
screw locking varnish (or safetynuts)
2 x m8 threaded rod about 15,5 cm
thingiverse
free
Filamentspool-holder 9cm V1.2 + Sizeable Filamentholder by thing6he
...s (like spools from rep-rap-world, 1kg) and added an fully printable non-spool-filament-holder.
i hope someone could need it too.
thingiverse
free
Filamentspool holder by jkarsten
... the stl with both sides.
then you need a 25mm tube. i used a steel one
i use a magnet that i glued behind the wall for my tools.
thingiverse
free
Filamentspool holder for 200mm spools by syllie
...e
thingiverse
spool holder with bearings for holding a 200mm filament spool.
partlist:
4 x 608zz bearing
2 x 8mm axis
12 x screw
thingiverse
free
spool cone for filamentspool M8 nut screw Anet A8 by sPiet
...ck anet a8 acrylic spoolholder.
created with solidedge st9 eduedition.
.par file is downloadable to modify the cone to any size.
thingiverse
free
Filamentspool Wallmount (Wandhalter) by transwarp2010
...ware and printed twice, to get the opposite part.
i add the original freecad-file, if you want to play with the design. have fun!
thingiverse
free
Anet A8 - Filamentspool holder by S3NS3Y
...ling appears do not worry.
do not use without m8 rod. the long tube beam section is not supposed to work without rod enforcement.
thingiverse
free
Spool Adapter
...spool adapter thingiverse filamentspool adapter for big...