GrabCAD
Filament Holder
by GrabCAD
Last crawled date: 1 year, 11 months ago
This is my filament holder. I printed it in Prusa PETG which comes in an orange that really pops. The roll is of a thickness that is strong without bulk while accommodating any brand of filament I've had. And it's easy to lift out. The roller runs on two 608 skateboard type bearings which is especially nice when using flexible filament.
A center roller works a lot better than edge rollers if you've vacuum bagged a near empty spool and it's warped.
There's room for at least two 1kg spools but I've never had a need to have more than one up.
Best to print the spool on end, with supports of course, otherwise it won't be as round.
A center roller works a lot better than edge rollers if you've vacuum bagged a near empty spool and it's warped.
There's room for at least two 1kg spools but I've never had a need to have more than one up.
Best to print the spool on end, with supports of course, otherwise it won't be as round.
Similar models
grabcad
free
Filament Holder
...sign is optimized for printing with a minimum amount of support material, which helps to reduce printing time and material waste.
grabcad
free
Universal stand-alone filament spool holder (Fully 3D-printable)
...ou need a new filament spool holder, just 3d-print one! :)
instructions
http://bit.ly/1z5hr5t
video
http://youtu.be/x6arzewysze
grabcad
free
3D Printing Filament Spool Holder
...ear:
56.5 mm
52.5 mm
51.5 mm
31.3 mm
i've undersized the features slightly for 3d printing and tolerancing reasons.
enjoy!
grabcad
free
Filament Spool Clamp
...h prusa i3 pro.
i use the 3d printed 'geeetech i3 filament spool holder' by ali55 on thingiverse which works fine for me.
grabcad
free
Up! 3D Printer Spool Holder
...older for up! 3d printers with filament guide and cavity for filament filter. support wide and thin spools. must print two part2.
grabcad
free
Raise3D Filament Spool
...hat i've made silent spools with ball bearings. this spool uses two 608xx bearings and a 1/4-20 x 2.5in screw (or m6 x 70mm).
grabcad
free
3D printing Filament spool holder
...of the spool, diameter: 200mm (7.87 in), with: 55mm (2.16 in).
although my spool was 53.5mm wide.
you will need: 4 608 bearings.
grabcad
free
Spool roller for large 3D filament spools
...ools.
fits both large and small spools. easy to adjust for different sizes.
only extra hardware needed is 4 pcs m4x20mm screws.
grabcad
free
Voron 2 Spool Holder Large Configurable
...the spool width and the holder height. i recommend higher spool holder for heavier and large spools where the com is further out.
grabcad
free
Easy to print universal filament spool holder
...holder
grabcad
universal spool holder
- easy to print
- without support
- in one piece
you need additionally two 608 bearings.
Filament
grabcad
free
Filament
...filament
grabcad
basite indirgenmiş bir filament
grabcad
free
Filament cleaner
...filament cleaner
grabcad
cleans the filament to avoid any problems with filament while printing
grabcad
free
Filament holder
...filament holder
grabcad
filament holder
grabcad
free
Filament spool
...filament spool
grabcad
filament spool
grabcad
free
filament spool
...filament spool
grabcad
filament spool
grabcad
free
Filament Guide
...filament guide
grabcad
filament guide
grabcad
free
FILAMENT BOX
...filament box
grabcad
filament box
grabcad
free
Filament Holder
... not safe for a filament holder because when the filament gets stuck anywhere, the filament holder disc can come out of the slot.
grabcad
free
filament carrier
...filament carrier
grabcad
.... here a filament carrier for 1 kilogram filament ...
more patterns to follow ....
step, igs, stl
grabcad
free
Filament Clip
...filament clip
grabcad
filament spool clips
suitable 1.75mm filament. planned to hold tight on different rolls thickness.
Holder
grabcad
free
Holder
...holder
grabcad
holder, lamp holder
grabcad
free
holder
...holder
grabcad
holder
grabcad
free
Holder
...holder
grabcad
holder
grabcad
free
holder
...holder
grabcad
holder
grabcad
free
Holder
...holder
grabcad
holder
grabcad
free
Holder
...holder
grabcad
holder
grabcad
free
HOLDER
...holder
grabcad
holder
grabcad
free
holder
...holder
grabcad
holder
grabcad
free
Holder
...holder
grabcad
holder
grabcad
free
holder
...holder
grabcad
holder