GrabCAD
Elev8
by GrabCAD
Last crawled date: 8 months, 1 week ago
Specific Functions
1. One side can open up allowing you to use it on your torso
2. The ball pressure can extended up, down and side to side. as well as having a 360 movement ball for rolling through muscles
4. Extendible ball shoulder be easy to use with one hand
Material
1. Supporting roller is made of hard foam
2. Outside bars are made of a very firm plastic
3. Extendable stick made of metal or hard plastic
4. Ball made of hard but smooth surface plastic
1. One side can open up allowing you to use it on your torso
2. The ball pressure can extended up, down and side to side. as well as having a 360 movement ball for rolling through muscles
4. Extendible ball shoulder be easy to use with one hand
Material
1. Supporting roller is made of hard foam
2. Outside bars are made of a very firm plastic
3. Extendable stick made of metal or hard plastic
4. Ball made of hard but smooth surface plastic
Similar models
3dwarehouse
free
Pololu Ball Caster with 1/2' Plastic Ball
... with 1/2' plastic ball. this light ball caster uses a 1/2' diameter plastic ball. #12 #ball #ball_caster #caster #polulu
3dwarehouse
free
Pin holder tool
...eld to locate it onto the hole center and the other one should be used to make flat the pin and plastic faces. #punzón_pin_holder
3dwarehouse
free
Extended Tapered (2-Sided) Bar Leg (40-1/2' x 3-1/2')
...ariety of widths and comes available in dining table height (29') as well as both 34.5' and 35.5' island leg heights.
thingiverse
free
tab to hold things to 1/4" plastic. by TwoBadCatsLLC
...ightly.
window tab 2 265 has a round part .265" thick so it will be somewhat snug but you can tighten it down all the way.
thingiverse
free
1/2" Ball Bearing Star Fidget Spinner - Wingnut2k #4 by wingnut2k
...only about 3" in diameter overall.
i would heat up the print and ball bearing with warm water and the bearings will slip in.
grabcad
free
Pen
...ll point pen made up of plastic material.
it is a use and throw type pen rather with a refill which can be re-used several times.
thingiverse
free
Small camera adjustable stand (with 1/4" hardware slots) by MrScottFletcher
... choosing. versatile, flexible, and scalable.
the sjcam 5000+ holder can be found here:https://www.thingiverse.com/thing:4662376
cg_trader
$5
4 arms Dominus Knight conversion part | 3D
...ide panel and can fit up to 4 plastic shoulders.
a few minor conversion cuts will be required to cover the lower side components.
cg_trader
$3
Plastic Ball Valve
...plastic ball valve
cg trader
a 1/2" plastic ball valve.
thingiverse
free
Longhorn Fidget Spinner - Wingnut2k by wingnut2k
...ter and the bearings will slip in.
edit: i uploaded a model that uses (3) 1/4" nuts in lieu of the 1/2" ball bearings.
Elev8
thingiverse
free
ELEV8 Gripper Bracket by jleeman
...elev8 gripper bracket by jleeman
thingiverse
mounting bracket to secure gripper to the flight deck of the elev8 v2
thingiverse
free
Nucleus 13inch beaker bong accessories by matt8588
...upgraded the 3 inch downstem for $6 with an elev8 silicone...
thingiverse
free
XBee Parallax USB Adapter Monitor Clip by jleeman
...i decided that my ground side radio for the elev8 needed a bracket so it wasn't flopping around. i...