Thingiverse
Electric Football by bblattbot
by Thingiverse
Last crawled date: 3 years, 1 month ago
This is a design for an electric ducted fan powered football.
In addition to the printed parts, this football requires the following:
-a 70mm fan (left handed version)
-an edf motor no larger than 28mm od
-a shaft adapter to fit the fan onto the motor
-a 40- 80 amp speed controller
-lipo batteries. I used 2 1000 mah 3s batteries wired in series and placed on opposite sides of one another to balance the weight
-a pwm control signal. I am using a servo tester but a microcontroller/accelerometer combo would be better for detecting throws and catches.
-a method of attaching the components inside of the shell. I packed them in with bubble wrap and tape.
total weight: 25 oz or less
A WORD OF CAUTION: THIS THING MIGHT BE DANGEROUS AND IS NOT A TOY! Build and use at your own risk.
This device consumes a large amount of power and has components that spin at extremely high speeds. Safety glasses and protective gear are advised.
Crash survivability has not yet been tested but I predict that it is extremely low. I would also avoid catching this with anything other than a fishing net at the end of a 10 foot pole.
Here is a bench test video of the edf unit:http://youtu.be/sk74hzTnlg4
In addition to the printed parts, this football requires the following:
-a 70mm fan (left handed version)
-an edf motor no larger than 28mm od
-a shaft adapter to fit the fan onto the motor
-a 40- 80 amp speed controller
-lipo batteries. I used 2 1000 mah 3s batteries wired in series and placed on opposite sides of one another to balance the weight
-a pwm control signal. I am using a servo tester but a microcontroller/accelerometer combo would be better for detecting throws and catches.
-a method of attaching the components inside of the shell. I packed them in with bubble wrap and tape.
total weight: 25 oz or less
A WORD OF CAUTION: THIS THING MIGHT BE DANGEROUS AND IS NOT A TOY! Build and use at your own risk.
This device consumes a large amount of power and has components that spin at extremely high speeds. Safety glasses and protective gear are advised.
Crash survivability has not yet been tested but I predict that it is extremely low. I would also avoid catching this with anything other than a fishing net at the end of a 10 foot pole.
Here is a bench test video of the edf unit:http://youtu.be/sk74hzTnlg4
Similar models
thingiverse
free
cooling jacket - a lot of cool air in the jacket by ahmadsuhaimi
...he handle from this https://www.thingiverse.com/thing:2868151
the video i testing it:-https://www.youtube.com/watch?v=8rg0xhmphzm
thingiverse
free
hair dryer (test) by zhaokbk2
...er.
there is no heating function at present!!!!!!
i bought edf from the website: https://item.taobao.com/item.htm?id=547891937024
thingiverse
free
10 Blade EDF Unit (ELECTRIC DUCTED FAN) by stustu242
...ore/__24929__b20_30_22l_fin_brushless_inrunner_motor_4220kv.html
worked great
please download this and print it if you can :)
thingiverse
free
Traxxis T-maxx electric conversion motor and battery mount by fjohn624
..., hold a standard battery and 540 sized motor. it has slots for velcro battery straps and a 30mm fan to help keep the motor cool.
thingiverse
free
Magnetic stirrer 120mm fan by Secondrobotics
... 120mm fan
x1 toggle switch
x1 9 volt battery or 10-12volt power adapter
x6 neodymium magnets
msc wire
50-100k ohm pot
superglue
thingiverse
free
vesc box by Rof3D
... the phase one for the control
this case hang to rucksuck where battery stay and it give power for the motor for retro e tool kit
thingiverse
free
edf motor by arinc
...edf motor by arinc
thingiverse
it is printable edf fan
thingiverse
free
70mm EDF duct by tom2016
...preciate feedback and improvements for the design. i have designed this duct to improve thrust and efficiency within an edf unit.
thingiverse
free
Thermostatic Fan Controller Case by Srbonham1
...ndard spdt.
wiring and components found here:https://www.audizine.com/forum/showthread.php/820187-diy-thermostatic-fan-controller
thingiverse
free
ReP_AL RC Micro Star Hexacopter by ReP_AL
...ight controlled by betaflight
props: 55mm with 1mm holes
battery: i use a turnigy nano tech 35-70c 1s 750mah
flight time: 5-6mins
Football
thingiverse
free
Footballer by Sevro
...footballer by sevro
thingiverse
figurine footballer with gate intended primarily for football coach for training purposes.
thingiverse
free
Football by Max_Massaro
...football by max_massaro
thingiverse
an american football
thingiverse
free
football by Budward
...football by budward
thingiverse
half a football on a platform
thingiverse
free
Football Box
...football box
thingiverse
footbal box
no need supports
thingiverse
free
Football by AMSSTEM79
...football by amsstem79
thingiverse
a 1/2 scale model football
thingiverse
free
football by t1dTom
...football by t1dtom
thingiverse
football 80 mm. rotate in thingview to see the strings.
thingiverse
free
Office Football
...office football
thingiverse
just a quick design of a football for the office. flexible filament recommended.
thingiverse
free
Football wall mount
...football wall mount
thingiverse
this is a football wall mount for standard size nfl footballs.
thingiverse
free
Toy Football
..., football is printed in tpu filament. football gets some great distance using 3dsolutech tpu - very firm tpu similar to cheetah.
thingiverse
free
Football by roman_hegglin
...football by roman_hegglin
thingiverse
give your dual extruder 3d-printer some work and print this football.
Electric
thingiverse
free
Electric toothbrush
...electric toothbrush
thingiverse
an electrical project where we make an electric toothbrush..... sort of
thingiverse
free
Electric box
...electric box
thingiverse
electric box
thingiverse
free
Electrical Panel - large electrical cabinet by NYC3D
...electrical panel - large electrical cabinet by nyc3d
thingiverse
large electrical cabinet
thingiverse
free
Electrical box
...electrical box
thingiverse
this is a electrical box for led light control box.
thingiverse
free
Electrical switch
...electrical switch
thingiverse
this is an electrical switch which can be printed very easily and no soldering is required.
thingiverse
free
electric longboard by MarcoMota01
...electric longboard by marcomota01
thingiverse
electric longboard
thingiverse
free
Electric Motor by TheDanMan
...electric motor by thedanman
thingiverse
an electric motor
thingiverse
free
BOX ELECTRIC by leonk
...box electric by leonk
thingiverse
box electric
thingiverse
free
Electric pallet by leonk
...electric pallet by leonk
thingiverse
electric pallet
thingiverse
free
electrical box by leonk
...electrical box by leonk
thingiverse
electrical box