Thingiverse
Dustpan broomstick wiper by CosmicBeyond
by Thingiverse
Last crawled date: 3 years ago
The pictures are kind of self-explanatory ;)
Basically you mount this to your dustpan so that after sweeping, you can run your broom's bristles over the "teeth" to wipe off the remaining stuck-on debris.
I would recommend printing in ABS with 100% infill, for strength and flexibility. I had to bend mine a little for it to fit. It might have otherwise snapped with a low infill (or using PLA).
I used .3 layer height, with a raft.
The length is about 7 1/2 inches x 1 1/2 inch in depth. Scale as necessary depending on your dustpan's size.
Three holes were added for the screw mounts, but you might have to drill them slightly larger (not too large though or it will crack). I used screws with a washer and bolt for added security, rather than just a screw by itself.
Basically you mount this to your dustpan so that after sweeping, you can run your broom's bristles over the "teeth" to wipe off the remaining stuck-on debris.
I would recommend printing in ABS with 100% infill, for strength and flexibility. I had to bend mine a little for it to fit. It might have otherwise snapped with a low infill (or using PLA).
I used .3 layer height, with a raft.
The length is about 7 1/2 inches x 1 1/2 inch in depth. Scale as necessary depending on your dustpan's size.
Three holes were added for the screw mounts, but you might have to drill them slightly larger (not too large though or it will crack). I used screws with a washer and bolt for added security, rather than just a screw by itself.
Similar models
thingiverse
free
Insta360 One R Case Mount with Cold Shoes - 1/4 inch Screw Mount by Garry1953
.....
i added a hole to make it easier to clean out the thread supports.
i used cura 4.80 with brim and tree supports at 70% infill.
thingiverse
free
Foscam security camera mount by JoMaGi
...k out another inch. (if there's demand, i guess i can extend it - but this thing works great.)
i added of the install pic.
thingiverse
free
Panel mount for 20mm round rocker switch. by flightbox
...e (4) 3/8", 1/2" or 5/8" #2 screws (depending on the surface you are mounting too)
m3 screws might work as well.
thingiverse
free
Wall Mounted Spool Holder by planet_3D
...ours on my cr-10 printed at 50mm/s. if you print it, post it in the "made" section. i would love to see pictures of it.
thingiverse
free
Skateboard Wall Hanging Clip
...he added strength.
you will also need two wall screws that go into screw inserts on your wall if you are not mounting into wood.
thingiverse
free
LED tea light candle holder by CosmicBeyond
...ter
added a slightly larger .stl size with a 2" inch (53mm) diameter (same height)
looks cool right side up, or upside down!
thingiverse
free
E3D Dual 40mm Fan Mount (Clampable) by Cjoutwest
...arm"
in order to use this design you will also need
14 - 1 inch 6/32 inch screws
2 - 2 inch 6/32 inch screws
16 - 6/32 nuts
thingiverse
free
''Off road" by IsaiRochaSegura
... inch (hight) and have two orifices for m3 screws. in this file i add the solidworks files for any modification that you want do.
thingiverse
free
Picatinny mount for Sony hdr-as15 in waterproof case by Zloy
... 1/4" tripod screw, so you don't have to unscrew metal plate.
added headstrap version also for 1/4" tripod screw
thingiverse
free
M-Lok AFG by Crashin_Machines
...acing so you can mount it to the handguard without using a rail. you will need to flip it on its side to print and use supports.
Cosmicbeyond
thingiverse
free
Simple shelf by CosmicBeyond
...rew holes are on each side, with a recessed surface for the screw head. i made this to display a container of oil diffuser reeds.
thingiverse
free
Cascading sponge holder by CosmicBeyond
...l' platform for a kitchen sponge. could also be used as a soap dish.
print in abs as it's more water resistant than pla.
thingiverse
free
Sriracha holder by CosmicBeyond
...en/bath-type items in abs (moisture resistant). for example- http://www.thingiverse.com/thing:1846356
5% infill @ .3 layer height
thingiverse
free
Letter & card file by CosmicBeyond
...ranslucent green pla.
5% infill
.3 primary
dimensions:
4 inches wide (101.60mm)
3 inches deep (76.20mm)
4 inches tall (101.60mm)
thingiverse
free
Shampoo/conditioner upside down holder by CosmicBeyond
...ter shells
three top/bottom layers
abs holds up well in moisture/water..
fits most 12 oz bottles ( example shown is 8.4 x 2.2. )
thingiverse
free
3 Belt Hanger by CosmicBeyond
...op sideways to fit.
**specs:
abs
50% infill
.3 micron
2 perimeter layers
3 top and bottom layers
***pictures show gold color abs.
thingiverse
free
Single belt holder by CosmicBeyond
...ring to fit).
pla could work too, but haven't tried it.
i used a .3 layer height with 100% infill. takes about 20 mins or so.
thingiverse
free
Wi-Fi Booster by CosmicBeyond
...res 5 inches in height, but you can scale up with your editor/slicer if necessary.
i printed mine in pla w/ .3 layer @ 5% infill.
thingiverse
free
Remote control caddy by CosmicBeyond
...+ depth (146.05mm)
3 1/2" height (88.90mm)
also included a large size
7" width + depth (177.80)
4" height (101.60)
thingiverse
free
Wall sconce for LED tea light by CosmicBeyond
...ghts, with slightly extra room for possible 1 3/4 inch diameter.
pla
5% infill
.3 micron
2 layer perimeter
3 layer top and bottom
Dustpan
turbosquid
free
Dustpan
...rbosquid
free 3d model dustpan for download as ige and sldas on turbosquid: 3d models for games, architecture, videos. (1225222)
3d_export
$15
Broom and Dustpan
...broom and dustpan
3dexport
broom and dustpan - 4k png textures
turbosquid
$4
Dustpan
... 3d model dustpan for download as max, 3ds, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1653502)
turbosquid
$12
Dustpan Wheel
...l dustpan wheel for download as 3ds, obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1266458)
3d_export
$12
Dustpan with brush 3D Model
...dustpan with brush 3d model
3dexport
dustpan brush cleaning sweep garbage
dustpan with brush 3d model cyrill 22335 3dexport
3ddd
$1
Dustpan with brush
...ersion of hairs converted in mesh. to use the hair and fur version remember to change to "mr. prim" in the effects tab.
3d_export
$5
dustpan
...max 2015,blender,cinema4d obj fbx stl warning:dont forget to active turbosmooth after final modeling. enjoy 3d modeling good luck
3d_export
$10
Dust Pan 3D Model
...dust pan 3d model 3dexport dustpan dust pan rubbish sweep broom clean dirt cleaning tools...
free3d
free
Dustpan
...dustpan
free3d
dustpan
thingiverse
free
Dustpan
...dustpan
thingiverse
dustpan for cat litter
Broomstick
turbosquid
$7
Household Tool - Broomstick
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Mauser C-96 Broomstick Machine Pistol
...broomstick machine pistol for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1179564)
3d_export
$13
STL CNC Router file Witch on a broomstick
...p sites, transmitted in any electronic way.<br>we guarantee the quality of all 3d models and wish you successful purchases!
thingiverse
free
Broomstick by Solidos3D
...broomstick by solidos3d
thingiverse
pla
thingiverse
free
broomstick converter by kaligabor
...broomstick converter by kaligabor
thingiverse
adapter for old type broomstick head.
thingiverse
free
Broomstick holder by ly3
...broomstick holder by ly3
thingiverse
broken broomstick holder replacement.printed in pla.
thingiverse
free
Broomstick holder by ly3
...broomstick holder by ly3
thingiverse
broken broomstick holder replacement.printed in pla.
thingiverse
free
broomstick converter by kaligabor
...broomstick converter by kaligabor
thingiverse
connect old broom head to new broomstick.
free3d
free
Witch on Broomstick v2
...witch on broomstick v2
free3d
witch on broomstick v2 printable, low poly model.
thingiverse
free
3 way broomstick holder by oferfrid
...3 way broomstick holder by oferfrid
thingiverse
holder for 3 broomsticks
Wiper
turbosquid
$60
wipers
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$9
Wiper
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Wipers 3D Model
...wipers 3d model
3dexport
wipers 3d model zarko 72473 3dexport
3d_export
$10
Floor Wiper 3D Model
...floor wiper 3d model
3dexport
wiper
floor wiper 3d model ankush2211 52516 3dexport
turbosquid
$6
3D car Wiper
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Volvo XC90 Rear Wiper Mechanism
...volvo xc90 rear wiper mechanism
3dexport
gear gear for volvo xc90 rear wiper
cg_studio
$5
Wipers Alca for car3d model
...d model
cgstudio
.3ds .max .obj - wipers alca for car 3d model, royalty free license available, instant download after purchase.
turbosquid
$35
Front Windscreen Wiper Set
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
cg_studio
$45
Wiper with transmission and drive unit3d model
...c4d .lwo .obj - wiper with transmission and drive unit 3d model, royalty free license available, instant download after purchase.
3d_export
$8
rear window wiper drive gear land rover freelander and fordfusion
...per drive gear land rover freelander and fordfusion
3dexport
rear window wiper drive gear land rover freelander and ford_fusion.