Thingiverse
Ducksie by kthuen
by Thingiverse
Last crawled date: 2 years, 11 months ago
This is Ducksie. When standing, he is a very confident little guy. Come close, and he may run away in his own, very special, way.
If you tilt Ducksie 45 degrees, there is a small wheel with a mechanisim inside. When you drive Ducksie around, the head will animate forward and back, and a little up and down.
This model is a print-in-place, which means that there is only 1 part and no assembly. It only takes a few hours to print. It may be a great way to test your printer or filament. It has all the classic print test properties: Wild overhangs, steep curves, very small details and moving parts. Maybe it also works as a great showcase on what makes 3D prints so versatile and fun.
The model requires no supports set up in the slicer, but after printing you will need to remove some built-in, very small support structures. Here is how to handle them: Start by cutting off the small supports below the wheel. Then turn the whell a bit, and polish it to be perfetly round on the area where the support was. When the wheel is turning perfectly, turn it to the position where the full neck is visible. Now you can carefully cut away the supports that is on the left and right side of the neck, just below the head. This may be the tricky part.
It should be an easy print if you have PLA of a good quality and your printer is perfectly set up. While testing the print, I had problems with some filaments, but I think enabling "Z hop when retracted" did the trick.
https://www.youtube.com/watch?v=E-voKnizqjM
Have fun!
If you like my design, and want me to do more, you can tip me here: https://www.paypal.com/paypalme/kthuen
If you tilt Ducksie 45 degrees, there is a small wheel with a mechanisim inside. When you drive Ducksie around, the head will animate forward and back, and a little up and down.
This model is a print-in-place, which means that there is only 1 part and no assembly. It only takes a few hours to print. It may be a great way to test your printer or filament. It has all the classic print test properties: Wild overhangs, steep curves, very small details and moving parts. Maybe it also works as a great showcase on what makes 3D prints so versatile and fun.
The model requires no supports set up in the slicer, but after printing you will need to remove some built-in, very small support structures. Here is how to handle them: Start by cutting off the small supports below the wheel. Then turn the whell a bit, and polish it to be perfetly round on the area where the support was. When the wheel is turning perfectly, turn it to the position where the full neck is visible. Now you can carefully cut away the supports that is on the left and right side of the neck, just below the head. This may be the tricky part.
It should be an easy print if you have PLA of a good quality and your printer is perfectly set up. While testing the print, I had problems with some filaments, but I think enabling "Z hop when retracted" did the trick.
https://www.youtube.com/watch?v=E-voKnizqjM
Have fun!
If you like my design, and want me to do more, you can tip me here: https://www.paypal.com/paypalme/kthuen
Similar models
thingiverse
free
Snappy - The talking aligator by kthuen
... request it, i can make a version of the wheel that can have a kind of tpu tire. but i have no tpu filament to test it.
have fun!
thingiverse
free
3D-PrintCreator Torture Test (for support testing) by ChatToBrian
...is very difficult because you can hardly remove the support, but if you succeed, you have a great set of settings in your slicer.
thingiverse
free
Raise3D Clip for spoolholder by ABH_
...ng to use this clip.
the clip prints without supports, as support is built-in. you have to break away the small taps in the slot.
thingiverse
free
kryptonian_command_key_rotated by brianskeen
... rotated it so when you print it out with supports you do not have to do any cutting away of the supports it prints it perfectly.
thingiverse
free
Skateboardz by muzz64
...pecial way and / or of them doing some amazing stunts!
note: if you like this check out the rest of my fun and practical designs.
thingiverse
free
Mini 0.4mm Filament Spool by FunbieStudios
...er use the full spool with supports or you may just use print 2 halves and then glue them later (to avoid supports).
have fun! =)
thingiverse
free
puzzle plane
...it is very fun for people who like to make things. great present. it also may need some sanding if one of the slots are too small
thingiverse
free
Bellsprout by Im_Ryno
...r.
that, and i added a small cylinder to the top of the neck and a hole in the back of the head to make attaching the two easier.
thingiverse
free
JOHNNY 5 MODEL NECK PART by Basic3Dprinting
...y is so u can still add a screw so you can turn the head. also left the solidwork files in there if anyone wants to make changes.
thingiverse
free
Straw builder by spaceballs
...on any printer. use normal bendy straws and you can turn a small print into a big building, bridge, or anything you can think of!
Kthuen
thingiverse
free
Easter Lily by kthuen
... great for the flower.
both the stems and the flower can be printed without any support. a raft is a good idea though.
have fun!
thingiverse
free
Village Puzzle by kthuen
...ality on the houses, i suggest to use a resolution of 0.12 no supports needed.
the wing on the mill should be glued on.
have fun!
thingiverse
free
Snappy - The talking aligator by kthuen
... request it, i can make a version of the wheel that can have a kind of tpu tire. but i have no tpu filament to test it.
have fun!