Thingiverse
Dremel Slicer by Menneset
by Thingiverse
Last crawled date: 3 years ago
The Dremel Slicer tool will help you to make perfectly straight cuts in many materials with a rotary tool such as the Dremel 4000.
Print the parts provided, two of the base part. Note that there are two different sizes of the Base, print ONE of those two, twice. Dremel_Slicer_Base is shown in the pictures, Dremel_Slicer_Base_Short is the same thing but it holds the cutting board about 6mm lower. Again, print two of the same, not one of each.
In addition to the printed parts you will need two 8mm steel shafts, four LM8UU linear bearings, a 4mm x 35mm bolt and nut, a 3mm x 60mm steel shaft, and two small sheet metal or wood screws. You will also need a Dremel 4000 or similar rotary tool.
All of the above parts, except for the bearings, I salvaged from old equipment but they should be fairly easy to find online. The 8mm shafts came out of a couple of old inkjet printers, the 3mm shaft came from an old CD ROM drive they pretty much all have one. If you cannot find the 3mm shaft, a 3mm or 1/8 screw should work as well.
The length of the board will need to be at least as long as your 8mm shafts are. My board is 12mm or 1/2 inch thick. A 3/4 board will bring the work closer to the shaft of the Dremel if that is what you need. The short base will move the work further away from the Dremel shaft.
Jan 16 Update: I replaced the Carriage and the Hinge files. I reworked the hinge mechanism somewhat, I believe the Dremel will be sturdier than it was prior. It should also be a tad bit easier to print. Yes, I replaced the 123dx file as well. :)
A note on licensing. I appreciate credit and kudos for my work, everyone does. I do not disallow commercial use of my work. If you can make a buck or two off of this then good for you, go for it! But remember where it came from. If you find it useful then buy me a beer. If you use it to make money, then buy me a six-pack. Enjoy!
Print the parts provided, two of the base part. Note that there are two different sizes of the Base, print ONE of those two, twice. Dremel_Slicer_Base is shown in the pictures, Dremel_Slicer_Base_Short is the same thing but it holds the cutting board about 6mm lower. Again, print two of the same, not one of each.
In addition to the printed parts you will need two 8mm steel shafts, four LM8UU linear bearings, a 4mm x 35mm bolt and nut, a 3mm x 60mm steel shaft, and two small sheet metal or wood screws. You will also need a Dremel 4000 or similar rotary tool.
All of the above parts, except for the bearings, I salvaged from old equipment but they should be fairly easy to find online. The 8mm shafts came out of a couple of old inkjet printers, the 3mm shaft came from an old CD ROM drive they pretty much all have one. If you cannot find the 3mm shaft, a 3mm or 1/8 screw should work as well.
The length of the board will need to be at least as long as your 8mm shafts are. My board is 12mm or 1/2 inch thick. A 3/4 board will bring the work closer to the shaft of the Dremel if that is what you need. The short base will move the work further away from the Dremel shaft.
Jan 16 Update: I replaced the Carriage and the Hinge files. I reworked the hinge mechanism somewhat, I believe the Dremel will be sturdier than it was prior. It should also be a tad bit easier to print. Yes, I replaced the 123dx file as well. :)
A note on licensing. I appreciate credit and kudos for my work, everyone does. I do not disallow commercial use of my work. If you can make a buck or two off of this then good for you, go for it! But remember where it came from. If you find it useful then buy me a beer. If you use it to make money, then buy me a six-pack. Enjoy!
Similar models
thingiverse
free
Dremel 45º Chamfer Tool by Fedex1000
...remel 4000 but it should work for any dremel tool.
you also will need a m4 x 40mm screw with nut.
don't need supports at all.
thingiverse
free
Rotary Tool Cutoff Saw Hinge for Dremel Model 225 by stylesuxx
...del 225. you need to attach the axle for the tool before screwing in the dremel and then attach the rotary tool to it's axle.
thingiverse
free
Dremel 4000 Bracket for MPCNC -- Old -- by jlonomo
...the same shape.
thought that the dremel itself might be more capable of cutting than the flexible shaft, so designed this part.
thingiverse
free
DIY 3d Printed Dremel-Style Rotary Tool by Makernaut
...king good! so i decided to design and make my own 3d printed dremel-style rotary tool.
watch the video for assembly instructions.
thingiverse
free
Repraper.com 1kg spool bearing by mcentric
...aft diameter, just ask.
if printed correctly these bearings will roll quite nicely and reduce friction between spool and shaft.
thingiverse
free
Dremel Flex Shaft Adapter by Selelvian
...t-for-rotary-tool-4000-400-398-395-300-285-275-8200-/130720964908?pt=au_tool_parts_accessories&hash=item1e6f93a12c&_uhb=1
cults
free
DIY Dremel-Style Rotary Tool
....com/id/3d-printed-diy-dremel-style-rotary-tool/
note: economically, this project is feasible if you have your own 3d printer.
thingiverse
free
Anycubic i3 Mega Dremel Mount
... m3x16mm. if you're wondering, this is the rotary tool i used for this conversion.
the link in this post is an affiliate link
grabcad
free
Router base for Dremel 4000
...s but there was no router base. so this part will fit with the long collet and use same bolt and nut as supplied in the 4000 set.
thingiverse
free
Dremel 4000 Bench Mount by hiwwpoh
...ew holes for fastening the mount to your bench or a board and a slot in the base to accommodate a hook-and-loop strap or zip tie.
Menneset
thingiverse
free
DaVinci Lid Brace by Menneset
...ci lid brace by menneset
thingiverse
a simple, easy to make and use brace that will hold the lid of the davinci 3d printer open.
thingiverse
free
5mm LED clip by Menneset
...lds a 5mm led close to a surface. not the prettiest thing ever, but it is designed to be used for indirect light or backlighting.
thingiverse
free
Maze Box Redux keys by Menneset
...the maze box redux gift boxes.
the red one is maze 1, the easy one. perhaps i didn't fully think through the color choices...
thingiverse
free
Root 3 CNC NEMA 23 Spacer with Tab by Menneset
...oot 3 cnc that has an extra tab for adding a threaded rod cross piece to serve as a stiffener for the entire x carriage assembly.
thingiverse
free
Mega/Ramps Fan Mount by Menneset
...it has mounting holes for both 60mm fans and for 40mm fans. typically you will print two, but one alone could work in some cases.
thingiverse
free
Arduino Uno Model by Menneset
...be.
the dimensions came from this image by matthew beckler. thank you mr. beckler. another good source is, (as always,) adafruit.
thingiverse
free
T-Rex Tape Dispenser Revisited by Menneset
...ome on your desk and actually dispense a full roll of tape. it is especially awesome when printed with glow-in-the-dark filament!
thingiverse
free
Dremel Foot 45 degree hold by Menneset
...t; i am thinking that the head piece could have been bigger, i may come back and revisit that after i have used them for a while.
thingiverse
free
D&D Meeples Smaller Party by Menneset
...ee. basically i just used meshmixer to cut his tray of meeples into fourths and named them a,b,c,d. hope this helps someone else.
thingiverse
free
Light Ring for 65mm CNC Spindle by Menneset
...er you normally do should be just fine. i used e3000 to glue the led ring to the clamp, but again, use whatever you have on hand.
Dremel
turbosquid
$2
Dremel Fuge
...osquid
royalty free 3d model dremel fuge for download as stl on turbosquid: 3d models for games, architecture, videos. (1296921)
thingiverse
free
Dremel Somunu - Dremel Nut by Pxlred
...dremel somunu - dremel nut by pxlred
thingiverse
dremel mounting nut. 3/4"-12tpi
tested on dremel 300.
thingiverse
free
Dremel holder
...dremel holder
thingiverse
dremel holder
thingiverse
free
dremel by Osso32
...dremel by osso32
thingiverse
this is a accesory for the dremel holder
thingiverse
free
Dremel by operrr
...dremel by operrr
thingiverse
easy to repeat dremel. motor size d28mm, l43mm.
thingiverse
free
Dremel Mount by 7145d33p
...dremel mount by 7145d33p
thingiverse
dremel mount
thingiverse
free
clip for dremel by Geogeorge
...clip for dremel by geogeorge
thingiverse
dremel holder
thingiverse
free
Clamp for a dremel by antaviana
...clamp for a dremel by antaviana
thingiverse
clamp for a dremel
thingiverse
free
soporte dremel by lariox
...soporte dremel by lariox
thingiverse
soporte para dremel
thingiverse
free
Dremel Holder by PabloBC
...dremel holder by pablobc
thingiverse
holder to fix the dremel tool.
Slicer
3d_export
$19
Slicer 3D Model
...slicer 3d model
3dexport
slicer
slicer 3d model alandeff 39830 3dexport
turbosquid
$15
Throat Slicer
...quid
royalty free 3d model throat slicer for download as fbx on turbosquid: 3d models for games, architecture, videos. (1420873)
turbosquid
$1
Pineapple Slicer
...d
royalty free 3d model pineapple slicer for download as max on turbosquid: 3d models for games, architecture, videos. (1686004)
turbosquid
$5
Banana Slicer
... model banana slicer for download as sldpr, ige, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1607725)
turbosquid
$29
Bread Slicer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$29
Cheese Slicer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Apple Slicer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$7
Eggs Slicer
...del eggs slicer for download as 3ds, obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1455288)
3d_export
$25
Meat slicer 3D Model
...meat slicer 3d model
3dexport
meat slicer
meat slicer 3d model guzayya 55834 3dexport
turbosquid
$6
egg slicer
...
royalty free 3d model egg slice for download as 3dm and max on turbosquid: 3d models for games, architecture, videos. (1672497)