Thingiverse
Dragonboard 410c Case by giantpune
by Thingiverse
Last crawled date: 3 years ago
This is a case for a Dragonboard 410c. Access is there for power, all the ports on the front, the switches on the bottom, and the gpio header. The holes are designed to fit the M2.5x8 socket head screws I have and the matching M2.5x.45 hex nuts. Tolerance is tight enough that the bottom of the case holds the nuts without dropping them, and the top of the case holds the screws without dropping them.
Similar models
thingiverse
free
DragonBoard 410c case by AlexGale
...dragonboard 410c case by alexgale
thingiverse
this is a case that holds a qualcomm dragonboard 410c
thingiverse
free
Dragonboard 410c Case by zeroepoch
...ery slightly to reduce covering the connectors. the connector overlap could have just been my printer doing that, but who knows.
thingiverse
free
96Boards 410c DragonBoard Case by ljking
... item only linked with the cables.
a 75x75mm vesa mount can be added to the micro-box to allow easy mounting onto a vesa monitor.
thingiverse
free
Raspberry Pi 3 Case (without Screws) by FinalMadness
...ithout screws) by finalmadness
thingiverse
made a case that don't needs screws and nuts. the top simple snaps in the bottom.
thingiverse
free
Mini NES Pi 3 Case w/ Hex Nut Slots by ilucipher
... a later date if you want to.
the hex-nut slots did not hold up entirely by friction, so i used super glue to keep them in place.
thingiverse
free
door magnet
...screws with nuts are needed to make them.
in my case spacers were necessary. v.2 was enlarged by 7mm to make it fit without pads.
thingiverse
free
Drop-in t-slot nuts by Dimon372
...a remix without nut. so i just screw bolt to pla and it hold fine.
will update over few month if i broke it or it will not work )
grabcad
free
Replicape Case
...crews holding.
srews on top: m3x16 mm
screws on bottom: m3x ** mm
** it depends on the thickness of the wall you attach it to.
thingiverse
free
JTAGulator Case by hiburn8
...lly designed acrylic case so its a perfect fit. just needs 3 raisers, nuts and screws to hold the top and bottom pieces together.
thingiverse
free
One-Up Bed Adjust Nut Holder by jeffrey892
...d the nut. this one just slips over the bottom plate and holds the nut from turning. it fits tightly so it won't come loose.
Dragonboard
thingiverse
free
DragonBoard 410c case by AlexGale
...dragonboard 410c case by alexgale
thingiverse
this is a case that holds a qualcomm dragonboard 410c
thingiverse
free
Dragonboard 410c Case by zeroepoch
...ery slightly to reduce covering the connectors. the connector overlap could have just been my printer doing that, but who knows.
thingiverse
free
96Boards 410c DragonBoard Case by ljking
... item only linked with the cables.
a 75x75mm vesa mount can be added to the micro-box to allow easy mounting onto a vesa monitor.
thingiverse
free
Dragonboard IFC6410 Case with 80mm Fan Attachment by alexgian
.... i've yet to tests the bottom part of the case, but the top part works perfect with a thermaltake 80mm usb fan from amazon.
410C
thingiverse
free
DragonBoard 410c case by AlexGale
...dragonboard 410c case by alexgale
thingiverse
this is a case that holds a qualcomm dragonboard 410c
thingiverse
free
96Boards 410c DragonBoard Case by ljking
... item only linked with the cables.
a 75x75mm vesa mount can be added to the micro-box to allow easy mounting onto a vesa monitor.
thingiverse
free
Dragonboard 410c Case by zeroepoch
...ery slightly to reduce covering the connectors. the connector overlap could have just been my printer doing that, but who knows.
thingiverse
free
Servo holder for 41 mm standard servo by mojo_replica
...rc truggy project. originally made for the modelcraft standard-servo bms-410c ...
thingiverse
free
Autonomous-Webserved-Tanktrack-Robot by donboy
...bms-410c. you can buy this in europe at conrad (https://www.conrad.de/de/modelcraft-standard-servo-bms-410canalog-servo-getriebe-material-kunststoff-stecksystem-jr-404753.html). the servo is therefore interesting, because he has a...
grabcad
free
Dragon Board 410c
... accurate, due to the lack of info in the manual but it should be close enough for most jobs, and the mounting holes are correct.
3dwarehouse
free
Marshall JVM 410C
...
3dwarehouse
100w 4-channel guitar combo #410c #amp #amplifier #combo #electronic #equipment #guitar #jvm #marshall #music #tube
3dwarehouse
free
Marshall JVM Series
...205h and 410h. please rate :) #205c #205h #215c #410c #410h #amp #amplifier #cabinet #electronic #guitar #jvm #marshall #music...
Giantpune
thingiverse
free
DROK multimeter x2 mounting plate by giantpune
...4x4in electrical box. my use case is for wiring a generator to supply power to my house. 1 multimeter for each of the two legs.
thingiverse
free
Spool adapter for small sewing machine by giantpune
... on a sewing machine with a smaller spindle up top. openscad file is attached in case you need to modify it to change the sizes.
thingiverse
free
Cinderella's Castle - fixed by giantpune
...0% size and exported. this seems to have gotten rid of the weirdness. printed first try without falling apart half way through.
thingiverse
free
Seat Release for 2004 Hyundai Tiburon by giantpune
...e stock part. it's quick. its dirty. it has no rounded pretty edges. but it works. and it costs about $0.15 and an hour.
thingiverse
free
End cap for my window blinds by giantpune
...i successfully made this with abs, 0.2 layer height, no raft or supports, and the popular 230/110 extruder and build plate temps.
thingiverse
free
Odroid XU4 + Mediasonic Probox NAS by giantpune
...oid xu4 case fits this.
parts links for usa -http://ameridroid.com/products/odroid-xu4http://www.amazon.com/gp/product/b003x26vv4
thingiverse
free
Flashforge Creator Pro top camera mount by giantpune
...hingiverse.com/thing:725457. that part mounts a camera to get a horizontal view and this part mounts one to get a vertical view.
thingiverse
free
Flashforge Creater Pro rear side plugs by giantpune
... its top hooks in place.
printed with 0.1 layer height, abs. supports are built in and should be removed when its done printing.
thingiverse
free
Larger clamp for breadboard vise by giantpune
...f the vise, right?
to make this, you still need to print one of the bases from the original model. this is just a different arm.
Case
3d_export
$1
case
...case
3dexport
case
archibase_planet
free
Case
...case
archibase planet
showcase show-case glass case
glass-case + cakes - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
showcase show-case glass case
glass-case for chips - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case shelving drawer
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case rack locker
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case drawer kitchen furniture
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case cupboard shelving
glass case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case handbag suitcase
case - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case suitcase
case 5 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
locker case dresser
case - 3d model (*.gsm+*.3ds) for interior 3d visualization.