Thingiverse
Diy Qi Charger by Diymaster1
by Thingiverse
Last crawled date: 3 years ago
This is a DIY Qi charger case that I made for my new iPhone x. It is really compact and minimal in design. It utilizes a small and cheap qi charging circuit bought from eBay for less than 3 USD and a micro USB cable for 1 USD. See link down below.
The installation process is really simple,
1 Firstly take away all the support material and sand everything down if you want to paint it. 2. Desolder the led and mark its orientation so that you don't mix the colors up.
2 Then use really small screws (i don't have the exact measurement for them) to secure the PCB then solder on the led in the right position and cut excess leads off.
3 Then secure the charging coil by putting its wires in the cable channel and just put it in its place.
4 Lastly, put the lid on and screw it in place carefully.
5 Done, you now have your very own Qi charger for 3-4 USD depending on if you buy the cable or not and where you buy the circuit.
If you decide to make one of your own, pls share your new Qi chargers with the rest of us, cheers!
This one is the one I used and it is type 1: https://www.ebay.com/itm/Qi-Wireless-Charger-PCBA-Circuit-Board-Coil-Wireless-Charging-Pad-Micro-USB-DIY/371831176614?ssPageName=STRK%3AMEBIDX%3AIT&var=640820050412&_trksid=p2060353.m2749.l2649
Or this one but it uses a rectangle led: https://www.ebay.com/itm/1pc-Qi-Wireless-Charger-PCBA-Circuit-Board-With-Coil-Wireless-Charging-Gifts/122860109536?_trkparms=aid%3D222007%26algo%3DSIM.MBE%26ao%3D2%26asc%3D49924%26meid%3D94ac19a0c49d49fda5095261aace4bc3%26pid%3D100005%26rk%3D6%26rkt%3D6%26sd%3D371831176614%26itm%3D122860109536&_trksid=p2047675.c100005.m1851
Micro usb cable for 1 USD:https://www.ebay.com/itm/3-6-10FT-Braided-Fast-Data-Sync-Charge-Cable-Cord-For-IOS-iPhone-Type-C-Android/162758143910?ssPageName=STRK%3AMEBIDX%3AIT&var=461792374615&_trksid=p2060353.m2749.l2649
The installation process is really simple,
1 Firstly take away all the support material and sand everything down if you want to paint it. 2. Desolder the led and mark its orientation so that you don't mix the colors up.
2 Then use really small screws (i don't have the exact measurement for them) to secure the PCB then solder on the led in the right position and cut excess leads off.
3 Then secure the charging coil by putting its wires in the cable channel and just put it in its place.
4 Lastly, put the lid on and screw it in place carefully.
5 Done, you now have your very own Qi charger for 3-4 USD depending on if you buy the cable or not and where you buy the circuit.
If you decide to make one of your own, pls share your new Qi chargers with the rest of us, cheers!
This one is the one I used and it is type 1: https://www.ebay.com/itm/Qi-Wireless-Charger-PCBA-Circuit-Board-Coil-Wireless-Charging-Pad-Micro-USB-DIY/371831176614?ssPageName=STRK%3AMEBIDX%3AIT&var=640820050412&_trksid=p2060353.m2749.l2649
Or this one but it uses a rectangle led: https://www.ebay.com/itm/1pc-Qi-Wireless-Charger-PCBA-Circuit-Board-With-Coil-Wireless-Charging-Gifts/122860109536?_trkparms=aid%3D222007%26algo%3DSIM.MBE%26ao%3D2%26asc%3D49924%26meid%3D94ac19a0c49d49fda5095261aace4bc3%26pid%3D100005%26rk%3D6%26rkt%3D6%26sd%3D371831176614%26itm%3D122860109536&_trksid=p2047675.c100005.m1851
Micro usb cable for 1 USD:https://www.ebay.com/itm/3-6-10FT-Braided-Fast-Data-Sync-Charge-Cable-Cord-For-IOS-iPhone-Type-C-Android/162758143910?ssPageName=STRK%3AMEBIDX%3AIT&var=461792374615&_trksid=p2060353.m2749.l2649
Similar models
thingiverse
free
Galaxy S7 wall mounted Wireless charger by fifipil909
...-pcba-circuit-board-with-coil-charging-pad-module-pop/263427070166?sspagename=strk%3amebidx%3ait&_trksid=p2060353.m2749.l2649
thingiverse
free
Coin capsule tube 30mm and 33mm by jalla2000
...sspagename=strk%3amebidx%3ait
http://www.ebay.com/itm/182199967698?_trksid=p2060353.m2749.l2649&sspagename=strk%3amebidx%3ait
thingiverse
free
DIY 1s Charger / 1s Lader by zaphi
...strk%3amebidx%3ait
power suply:http://www.ebay.de/itm/221961044643?_trksid=p2057872.m2749.l2649&sspagename=strk%3amebidx%3ait
thingiverse
free
Iphone 6 plus wireless charger car mount by theswink
...ne case: http://www.ebay.com/itm/221581383501?_trksid=p2059210.m2749.l2649&var=520440157463&sspagename=strk%3amebidx%3ait
thingiverse
free
GaPa Radio32 (KaRadio32) by yamaha_xg
...onverter-step-down-module-adjustable-3v-5v-16v-for-rc/221890985028?sspagename=strk%3amebidx%3ait&_trksid=p2060353.m2749.l2649
thingiverse
free
5" Retro Raz by Clpetrey
....
this was very fun to build. i think i have everything on here that i used in the build. if i'm missing anything let me know
thingiverse
free
360w psu cover by kimmerkesdal
...0w psu - http://www.ebay.com/itm/262626173745?_trksid=p2057872.m2749.l2649&var=561523999305&sspagename=strk%3amebidx%3ait
thingiverse
free
Earphone pad modification / Modification coussinet écouteur by 3D_CC_design
...x%3ait
padhttp://www.ebay.fr/itm/281669764696?_trksid=p2060353.m2749.l2649&var=580675186733&sspagename=strk%3amebidx%3ait
thingiverse
free
Headlamp Rev 3 by shaunmonster
...ll bits tool 0.3mm to 1.2 mm (http://www.ebay.ca/itm/361251633854?_trksid=p2060353.m2749.l2649&sspagename=strk%3amebidx%3ait)
thingiverse
free
Small box for QI wireless phone charger by MrSnoWie
...l's are made for that one.http://www.ebay.com/itm/121698735542?_trksid=p2057872.m2749.l2649&sspagename=strk%3amebidx%3ait
Diymaster1
thingiverse
free
Water Toy Horse Jumping Obstacle by Diymaster1
...er container has the dimensions 70mm x 53mm x 7mm so it can contain at max 26ml of waters but it´s enough fot these small horses.
thingiverse
free
Horse Jumping Obstacle by Diymaster1
...nted se my thing files. the obstacle is around 71mm tall, 36 wide and 31mm in depth these measurements are at the biggest points.
thingiverse
free
Toy Horse Cross Jumping Obstacle by Diymaster1
...d if desired.
i used wooden barbecue sticks across but you could just print out the cylinder i put in the thing files if wanted.
thingiverse
free
Toy Horse Jumping Obstacle by Diymaster1
... long or 130 mm.
v2.1 has square holders and v2 has circular holder. my printer works better with the square ones but both works.
thingiverse
free
Spool holder extension/Spacer by Diymaster1
...y with some glue but i did´t need it.
this thing might not fit every kind of filament spool or spool holder so keep that in mind.
thingiverse
free
LM 2596 dc-dc module MH by Diymaster1
...e module in place i used really small screws from an old salvage projects. if you don´t have any you could just glue it in place.
thingiverse
free
MacBook Air Wall Holder by Diymaster1
... thing. if you have any request, question, complaints, criticism regarding this thing or one of my other objects pls write to me.
thingiverse
free
Simple MacBook Air 11 Inch Stand by Diymaster1
... thing. if you have any request, question, complaints, criticism regarding this thing or one of my other objects pls write to me.
thingiverse
free
Zip Tie Cable Holder T-Slot Anchor by Diymaster1
...or something, just leave a comment and i will see what i can do.
pls also check out my other designs and my website 3duskrift.com
Qi
design_connected
free
Qi Seat RK-344
...seat rk-344
designconnected
mcguire furniture company qi seat rk-344 poufs computer generated 3d model. designed by robert kuo.
turbosquid
$8
Bathroom furniture set Scavolini QI
... furniture set scavolini qi for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1277208)
turbosquid
$15
7 CM Qi Charger Stand
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
set vases-no1- dei qi simple ceramic vase
...oration-creative-ornaments/dp/b07q9kw9yg<br>polys: 390.400<br>render: corona<br>formats: 3ds max 2015, obj, fbx
3ddd
free
Bross Eclipse
...eclipse 3ddd bross кресло eclipse (1662 qi / 1662l qi design enzo berti фабрика bross размер...
thingiverse
free
stand QI note 4 - support QI
...stand qi note 4 - support qi
thingiverse
support pour la base qi que l'on trouve sur ebay.
thingiverse
free
qi box by sniperdude
...qi box by sniperdude
thingiverse
qi box all parts from adafruit
thingiverse
free
Qi Dock by Stevetecx
...s very well. :)
attached is the:
qi dock.stl
for all the makers - qi dock.123dx
and a s3d gcode generated for a um2+ (pla, 0,15)
thingiverse
free
QI Nightstand by RalfRutke
...tand by ralfrutke
thingiverse
cut a whole in your nightstand or desk or whatever with a jigsaw.
place the qi inside and wire it.
thingiverse
free
Qi Charger Stand by OakLab
...ample, a qi charger corresponds to "aukey t20 qi wireless charger" (http://www.aukey.com/product/wireless-charger-t20).
Charger
3d_export
$5
charger
...ers in battle. this is the 18th century meaning of charger, and it’s based on the verb charge and its meaning “rush into battle.”
3d_export
free
Charger
...charger
3dexport
turbosquid
$15
Charger
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$3
Charger
...d model charger for download as skp, max, blend, stl, and obj on turbosquid: 3d models for games, architecture, videos. (1654816)
turbosquid
$1
charger
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$20
dodge charger 1972
...dodge charger 1972
3dexport
dodge charger 1972
3d_export
$20
dodge charger 1969
...dodge charger 1969
3dexport
dodge charger 1969
3d_export
free
dodge charger 1969
...dodge charger 1969
3dexport
dodge charger 1969
3d_export
$18
dodge charger
...dodge charger
3dexport
3d_export
$89
Charger 3D Model
...charger 3d model
3dexport
charger sea transopt industry 3d models
charger 3d model vitaly amurskiy 2286 3dexport
Diy
3d_export
free
DIY 3D Printer
...diy 3d printer
3dexport
diy 3d printer model
turbosquid
$10
Diy tiered
...l diy tiered for download as max, max, max, max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1603709)
turbosquid
$3
Diy Desk to Bench
...odel diy desk to bench for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1506589)
turbosquid
$2
DIY Moon Light
...model diy moon light for download as obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1501170)
3d_export
$8
DIY CNC Router 3D Model
...diy cnc router 3d model
3dexport
cnc; router; diy; homemade
diy cnc router 3d model maikeru86 58463 3dexport
turbosquid
$5
Diy Kitchen Cabinets
...itchen cabinets for download as 3ds, obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1197373)
3d_export
free
Download free Diying Plant 3D Model
...download free diying plant 3d model
3dexport
diying plant blender
diying plant 3d model visitorsama 98607 3dexport
3ddd
$1
DIY coffee table + decor
... рамка для фото
кофейный столик diy 400х350х600(h) мм. моделился по фото. внимание: материалы - corona.
turbosquid
$3
Diy Wire Lamp Shade
...free 3d model diy wire lamp shade for download as 3ds and fbx on turbosquid: 3d models for games, architecture, videos. (1347605)
cg_studio
$12
DIY MONGOLIAN LAMB STOOLS3d model
... hair soft pile white
.max - diy mongolian lamb stools 3d model, royalty free license available, instant download after purchase.