Similar models
thingiverse
free
Die with Deep Holes by SteedMaker
... enough holes or deep enough holes for those to be easily seen. if the holes are too shallow those don't visually stand out.
thingiverse
free
Basic balanced 6 sided die/dice
...s die is a 1x1x1cm die. it is balanced. the holes on the side are larger and the ones on the top and bottom are slightly smaller.
thingiverse
free
Die Filer Patterns by cae2100
...casting, print die_filer and die_filer(r) for the two halves, they have a 5/16 hole or 8mm hole in the pattern for locating pins.
thingiverse
free
Hole Die, Standard Size (16mm) by APHW
...
thingiverse
hole die
standard size - 16mm x 16mm x 16mm
please check out my new facebook page:https://www.facebook.com/3daphw
thingiverse
free
Wall Mountable Die Holder (Or anything that needs a 25mm hole) by BuddyC
...can store other things in it that needs a 25mm hole. it has four small holes for small screws to mount to a board or drywall etc.
thingiverse
free
Large Kids Die by kap42
...rse
this is a large die (10 cm), primarily made to be used by kids for playing.
the pip caps are to be glued into the pip holes.
thingiverse
free
Scale Playing Die by Philsphan56
...n56
thingiverse
i made a model of a playing die. the holes in the sides are to scale all you have to do is scale it up a little.
thingiverse
free
3 Hole Shell Holder Wall Mount by gwidgery
...ole shell holder wall mount by gwidgery
thingiverse
modded the 3 hole reloading die wall mount to fit extra shell casing holders
thingiverse
free
Standard 19mm dice (die) by ztander
...th holes that go through about 80 percent of the body. it gives a unique hollow look to the inside. this was made using nx 9.0.
thingiverse
free
3 Hole Reloading Die Wall Mount by gwidgery
...3 hole reloading die wall mount by gwidgery
thingiverse
needed a quick storage place for my reloading dies.
Die
thingiverse
free
DIE
...die
thingiverse
a large 70mm die. easy to roll
thingiverse
free
Charlie's sweet to die for die by dcgstudent
...charlie's sweet to die for die by dcgstudent
thingiverse
it's a die. excuse me a to die for die
thingiverse
free
Die by psa55
...die by psa55
thingiverse
die
thingiverse
free
Die Soldatin
...die soldatin
thingiverse
die soldatin
thingiverse
free
die by jmanley93
...die by jmanley93
thingiverse
fun die
thingiverse
free
DIE by NoHands
...die by nohands
thingiverse
simple die
thingiverse
free
Die by GunpowderGreen
...die by gunpowdergreen
thingiverse
just a simple die. :)
thingiverse
free
die by benjyjf
...die by benjyjf
thingiverse
die for board games
thingiverse
free
Fate Die
...fate die
thingiverse
just a sharp edged fate die. slightly larger than a normal die, at 17 mm square.
Hole
thingiverse
free
Holes, holes, holes! by runtimeterror
...ow and then.
the example photo shows two prints for 8 mm (7.6 .. 8.4) and 3 mm (2.6 .. 3.4).
the stl file is an example for 3 mm.
thingiverse
free
Hole Thru a Hole in a Hole by Denali3DDesign
...he imagination."
also available on shapeways if you want to purchase one already made: http://www.shapeways.com/model/723930
thingiverse
free
Hole In Wall
...hole in wall
thingiverse
hole in wall
thingiverse
free
holed oloid
...holed oloid
thingiverse
an oloid with holes because why not
thingiverse
free
hole by markhei1993
...hole by markhei1993
thingiverse
hole by mark [created on 3dtin]
thingiverse
free
TRINUS filament hole cover For spool hole by SheepsFeaTheR
...ol hole by sheepsfeather
thingiverse
trinus filament hole cover for spool hole
used to pass filaments from enclosure spool holes
thingiverse
free
hole cover by g3org
...hole cover by g3org
thingiverse
hole cover to close holes in profiles.
thingiverse
free
Hole finishing by manticus
...hole finishing by manticus
thingiverse
issue while drilling a hole, this is a hole fixer... lol
thingiverse
free
Hole Punch by cyberparra
...hole punch by cyberparra
thingiverse
simple hole punch to make holes in paper & cardboard
A
thingiverse
free
IKEA Vaxer net pot by khrazik
...ymore in my neighborhood, so i made my own. fits standard vaxer tubs. these are meant to be printed upside down with no supports.
thingiverse
free
Quiet control box for SKR 1.4 + cable mgmt layer. by Evilkoal
...thing into the electronics of the power supply.
let me know if anything is weird, but i haven't noticed anything not fitting.
thingiverse
free
UVA Mens' Basketball 2018-19 NCAA Trophy by the_qsr
...tube.com/watch?v=hxa3xd4dxcy
i've added a blank uva trophy in .stl and .obj for any other sports/years that you want to remix
thingiverse
free
Volcano Nozzle Case by garethps
...er nozzles. i could have just stretched it but then the number inserts wouldn't have fit properly, hence my first ever remix!
thingiverse
free
Savage Dragon - Image Comics by ZMilab
...s in my mini style.
if you want more models released weekly and access to exclusives join my patreon!
patreon.com/ziemba3d
enjoy!
thingiverse
free
Concordia and Britannia & Germania expansion boardgame insert by MitutoyoRaytek
...pacer2-v2.stl. i butchered my cardboard insert and turned it into a spacer.
spacer1-v2.stl is designed for printing in vase mode.
thingiverse
free
Renna by Legname
...renna by legname
thingiverse
renna in compensato da 3mm
thingiverse
free
Extension Cord Cable Mount Clip by max_davis
...x_davis
thingiverse
cable mount that fits a standard extension cord cable (up to 9mm). just use two screws or nails to mount it.
thingiverse
free
VESA monitor mount French Cleat by Rockster160
...ing/using this you claim all responsibility due to damage. use at your own risk!
fastened them to the monitors using m4*12 bolts.
thingiverse
free
GBS Zero Rain / Reverse Light IVA Angled Gasket by SeanWally
...pu.
the design includes a small seat adapter make sure that bolts used to secure the light are still mating at the correct angle.