Thingiverse
Decorative Box by Devmiser
by Thingiverse
Last crawled date: 2 years, 10 months ago
Designed this decorative box that can be used for any purpose. The design on the lid and the sides is not original, but I regret that I cannot find it again for purposes of providing attribution.
Printing:
I printed this at 70% scale to get the size I wanted, but you can choose your own scale.
I used 20% infill, but a higher infill would make the box more substantial.
I printed it in PLA at 20mm. The lid is a tight fit, so beware if your printer does not have good tolerances.
The box was printed without supports. I printed the lid on its side with support enforcements inside only, i.e. not on the decorative side.
Printed on a Prusa Mini+
Printing:
I printed this at 70% scale to get the size I wanted, but you can choose your own scale.
I used 20% infill, but a higher infill would make the box more substantial.
I printed it in PLA at 20mm. The lid is a tight fit, so beware if your printer does not have good tolerances.
The box was printed without supports. I printed the lid on its side with support enforcements inside only, i.e. not on the decorative side.
Printed on a Prusa Mini+
Similar models
grabcad
free
Box with Shutter Lid
... layer height and 100% infill on a prusa i3 mk3s printer. no supports are required.
i hope you can find this print useful, too.
thingiverse
free
Love Box by skartz
...tation your choose to print it. you may choose to use a raft.
filamenthttps://amzn.to/3eae7t8
walnut stainhttps://amzn.to/2vpk0u5
thingiverse
free
Container with carabiner lid ring by DragonsKeepArmoury
...inted with no supports and recommended 20% infill for strength
fully printed container is 3" in diameter and 2.5" tall
thingiverse
free
world of ward rotary table controller lid and box
...ace. the nuts were also glued with epoxy resin.
you may wish to print the top first and then decide whether to make your own box.
thingiverse
free
Herb/Weed Box by aceb4u
...s surface
no raft needed, supports may be use for the leaf as it a hole version depending on your printer, printed in 10% infill
thingiverse
free
Stackable jewelry/game tokens box with lid by kotadivine
...tically with the cross on the lid slotting into the groves in the bottom of the box itself.
print with supports, infill ~15-20%.
thingiverse
free
Mushroom Grinder Question Mark Box by HomieStarks
...of the lid. hope you guys enjoy! my first design for thingiverse....no design experience, just going off of will and instincts :)
thingiverse
free
Brother Scan N Cut CM300 Storage box with lid by Sagittario
...t supports, however the lid will require supports for the lip around the edge.
i printed using pla, 0.3mm layer height 20% infill
thingiverse
free
Literally just a Box by SCBWarEagle
... monoprice mini v2. since i am using a $200 printer, there are some bumps on the edges which can easily be removed via sandpaper.
thingiverse
free
Soda can
... rather than the supports being everywhere. scale down the lid until it looks proportional to the can. anyway, happy 3d-printing!
Devmiser
thingiverse
free
Castle Box by Devmiser
...-medieval-castle).
i designed the lower section and added a lip to the castle top to hold it in place.
i printed it at 90% scale.
thingiverse
free
Heart Shaped Box V2 by Devmiser
...e lid design going all the way through the lid.
the lid features a design by wslab. see https://www.thingiverse.com/thing:2445047
thingiverse
free
Heart Shaped Box by Devmiser
...the lid. see https://www.thingiverse.com/thing:2445047
i sliced this in prusaslicer at 0.1mm layer.
no supports needed
15% infill
thingiverse
free
Heart Shaped Valentine Box by Devmiser
...sliced this in prusaslicer at 0.1mm layer.
used supports on build plate only for the top. no supports for the bottom.
15% infill
Box
archibase_planet
free
Box
...box
archibase planet
box carton cardboard box
box 2 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Box
...box
archibase planet
carton cardboard box box
box 1 - 3d model (*.3ds) for interior 3d visualization.
3d_export
$6
box
...box
3dexport
box
3d_export
$5
Box
...box
3dexport
box
3d_export
$5
box
...box
3dexport
box
3d_export
$5
box
...box
3dexport
box
archibase_planet
free
Box
...box
archibase planet
box box for paper notebook pencil
box - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Box
...box
archibase planet
box carton cardboard box
box n170111 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Box
...box
archibase planet
box carton cardboard box
box n050411 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Boxes
...boxes
archibase planet
boxes box case bin
boxes n281213 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
Decorative
3d_ocean
$3
Decoration
...decoration 3docean ancient classic arabic.arab decoration decorative plaster isalm islamic other decorative objects panel pattern stone...
3d_ocean
$3
Decoration
...decoration 3docean ancient classic arabic.arab decoration decorative plaster isalm islamic other decorative objects panel pattern stone...
3d_export
$10
decor
...decor
3dexport
decor
3d_export
$5
decor
...decor
3dexport
decor
archibase_planet
free
Decor
...decor
archibase planet
decor statuette decoration leaf
decor 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$10
decor
...decor
3dexport
lattice decor
3ddd
$1
DECOR
...decor
3ddd
панель
decor
3ddd
$1
Decor
...decor
3ddd
панель
decor
3ddd
$1
Decor
...decor
3ddd
панель
decor
3ddd
free
DECOR
...decor
3ddd
панель
decor