Thingiverse
D-bot X/Y motion system linear guide blocks and pads made from Igus tribofilament by Rexipus
by Thingiverse
Last crawled date: 3 years ago
Note: I just posted a version 2.0 of these Igus-filament slider blocks and pads here:https://www.thingiverse.com/thing:2444422
Version 2.0 offers a more refined shape for the carrier blocks that blends better with the original D-bot parts. The version 2.0 sliding pads use less Igus material and reduce the surface contact area between the pads and the v-slot rail. I don't consider version 2.0 as a necessary upgrade for anyone who has already made and installed the version 1.0, though it may well perform better over time due to the improved slider pads. The carrier block changes are entirely cosmetic.
Hi. I removed all of the V-slot mini wheels from my D-bot's X/Y motion system and replaced them with sliding blocks that are lined with pads printed from Igus tribofilament. This system consists of a block which uses the same hole spacing as the D-bot gantry end caps and also the print carriage plates. The block is the same width as the two spacers and the mini v-slot wheels used in the D-bot design. To this block is applied a bearing pad printed from Igus tribofilament, which rides on both the 20mm wide flat surface of the 2040 V-slot rail, but also fits down into the V-shaped slot to keep things nicely aligned.
The purpose for using these blocks is:
1) Tighter fit between the print carriage and the 2040 v-slot print gantry, and between the ends of the gantry and the 2040 v-slot printer frame side rails. With these mounted fairly tightly there is no detectable play or slop in the system at all. Zero.
2) Low friction for a fully contacting sliding pad system. There was more friction in the moving parts as compared to the ball-bearing mini v-slot wheels, but I presume that this will smooth out in time as the parts "wear in" to each other. Also that friction is not necessarily a bad thing, as it could likely act as a sort of dampener that could reduce ringing. The steppers in a D-bot are plenty powerful enough to move these things around, so a slight dampening effect I see as a positive.
3) Long service life. I fully expect these pads to last longer than the rest of the D-bot itself. Igus advertises that their tribofilament wears up to 50 times less than other printable plastics. Their charts seem to bear that out, but then they would, wouldn't they?
4) The pads don't stick out beyond the ends of the plates the way the v-slot mini wheels do, so the pad blocks can move on the Y axis all the way up to the rear idler corner blocks of the frame. This means that the Y axis end stop screw has no problem getting to the Y axis end stop switch. With the mini V-slot wheels I had to bend the switch lever of the Y axis end stop switch out a little in order to get contact with the end stop screw. This seems like a trivial benefit, but was actually quite a nice little bonus to those of us whose end stop screws just didn't quite reach the switch.
I've been wanting to try the Igus filament for some time, and seeing quite a few people create D-bot mods that involve bolting Hiwin linear guide rods to their D-bot's top rails and print gantry inspired me to create this. I want the same benefits of the Hiwin linear guide system, without adding all of the weight of the Hiwin rails and sliding blocks, and while being much cheaper. One of the aspects of the D-bot design that really appeals to me is how the D-bot frame itself, because it's made using the OpenBuilds v-slot rails, can act as the guide rail for the Z and X/Y motion systems. The Hiwin solutions are adding tons of crap to the D-bot, and especially when you add the Hiwin rails and blocks to the 2040 print gantry of the stock D-bot design, you're adding quite a lot of weight to it that I just think is unnecessary and likely detrimental.
I've had these sliding blocks installed for going on a month of printing as of this posting, and my printer is busy for most of nearly every single day. So far these blocks have worked out great. Because the pads are designed to the exact dimension of the outer flat surface, and the V-slot itself, of the OpenBuilds V-Slot rails that the D-bot's framing is made of, they are a decently tight fit, and yet because they are printed from Igus's tribofilament, they will probably last forever, and show very low friction. It's not no friction, but the friction is surprisingly low for such full contact
My original idea for these used two shorter pads at either end of the sliding block, rather than a full-length pad, in order to minimize the surface contact area of the Igus material on the aluminum v-slot rail to drop friction even more, but it was more difficult than I'd assumed it would be to get all four pads (two each for top and bottom block per side) exactly aligned with each other. The full length pads fit down onto the tangs printed into the top surface of the blocks allowed extremely good alignment of the pads.
As printed, since I use a Bowden feed on my D-bot, I had slight blobbing at the corners that required a couple of minutes' worth of cleanup with an Xacto knife. Depending on how you print these, how the first layer goes down, etc. you may have to do some minor trimming to get the pads to snap down onto the tangs on the block. I left the tolerances extremely tight, tighter than you'd reasonably expect to achieve with a 3D print, specifically so that the pads would be exactly aligned on the bearing pads, and would be a good, tight fit in the v-slot slots.
Once printed and test fit to each other, I put a few drops of CA (super glue) onto the Igus filament pad bottoms, snapped them onto the blocks, and then clamped them down pretty hard onto a section of spare 2040 Vslot rail that I have left over from my D-bot. I left them clamped hard like this for a couple hours until I was sure the CA was dry.
I printed the blocks from PETG at 97% infill. I printed the pads from Igus tribofilament i170 at 70% infill with 3 perimeters in order to save material. I used 7 top layers at .1mm layer height, for fine resolution on the pads' bearing surfaces.
I've also tried the i180 filament. The 180 filament prints easier, and the prints look better, but it seems somehow softer than the 170, and the 170 also seems to have less friction. Igus claims in their marketing materials that 170 has the best wear behavior, but is more demanding of production technique. I can vouch for at least the second part of that.
I printed the Igus pads at 260 C with the bed at 90 C. I used a brim to lock it down after several attempts pealed up from my PEI sheet a little in one or two corners. I removed the brim with an Xacto knife afterward. I also used a brim on the main PETG blocks for the same reason.
This is version 1.0 of this item. My intent was to clean up the design of the blocks so they blend in better with the existing D-bot print carriage plates and the gantry bar end plates. I haven't done that refinement yet, but someone asked me for these files, so I'm putting it up now as is so they can be used. When I've refined the block design I'll post that updated block as 2.0. The change will only be cosmetic. While these blocks look fine as is, they can look better if I tweak the dimensions slightly and add a radius to the bottom ends of the block so they match the radius on the corners of the stock D-bot plates.
Here's a short Youtube video that I made showing this system in use on my D-bot:https://www.youtube.com/watch?v=ChPcBsqxBR4&feature=youtu.be
I'm attaching my SolidWorks 2016 source files for both blocks and pads. All of this is released with the Creative Commons - Attribution - Non-Commercial license.
Version 2.0 offers a more refined shape for the carrier blocks that blends better with the original D-bot parts. The version 2.0 sliding pads use less Igus material and reduce the surface contact area between the pads and the v-slot rail. I don't consider version 2.0 as a necessary upgrade for anyone who has already made and installed the version 1.0, though it may well perform better over time due to the improved slider pads. The carrier block changes are entirely cosmetic.
Hi. I removed all of the V-slot mini wheels from my D-bot's X/Y motion system and replaced them with sliding blocks that are lined with pads printed from Igus tribofilament. This system consists of a block which uses the same hole spacing as the D-bot gantry end caps and also the print carriage plates. The block is the same width as the two spacers and the mini v-slot wheels used in the D-bot design. To this block is applied a bearing pad printed from Igus tribofilament, which rides on both the 20mm wide flat surface of the 2040 V-slot rail, but also fits down into the V-shaped slot to keep things nicely aligned.
The purpose for using these blocks is:
1) Tighter fit between the print carriage and the 2040 v-slot print gantry, and between the ends of the gantry and the 2040 v-slot printer frame side rails. With these mounted fairly tightly there is no detectable play or slop in the system at all. Zero.
2) Low friction for a fully contacting sliding pad system. There was more friction in the moving parts as compared to the ball-bearing mini v-slot wheels, but I presume that this will smooth out in time as the parts "wear in" to each other. Also that friction is not necessarily a bad thing, as it could likely act as a sort of dampener that could reduce ringing. The steppers in a D-bot are plenty powerful enough to move these things around, so a slight dampening effect I see as a positive.
3) Long service life. I fully expect these pads to last longer than the rest of the D-bot itself. Igus advertises that their tribofilament wears up to 50 times less than other printable plastics. Their charts seem to bear that out, but then they would, wouldn't they?
4) The pads don't stick out beyond the ends of the plates the way the v-slot mini wheels do, so the pad blocks can move on the Y axis all the way up to the rear idler corner blocks of the frame. This means that the Y axis end stop screw has no problem getting to the Y axis end stop switch. With the mini V-slot wheels I had to bend the switch lever of the Y axis end stop switch out a little in order to get contact with the end stop screw. This seems like a trivial benefit, but was actually quite a nice little bonus to those of us whose end stop screws just didn't quite reach the switch.
I've been wanting to try the Igus filament for some time, and seeing quite a few people create D-bot mods that involve bolting Hiwin linear guide rods to their D-bot's top rails and print gantry inspired me to create this. I want the same benefits of the Hiwin linear guide system, without adding all of the weight of the Hiwin rails and sliding blocks, and while being much cheaper. One of the aspects of the D-bot design that really appeals to me is how the D-bot frame itself, because it's made using the OpenBuilds v-slot rails, can act as the guide rail for the Z and X/Y motion systems. The Hiwin solutions are adding tons of crap to the D-bot, and especially when you add the Hiwin rails and blocks to the 2040 print gantry of the stock D-bot design, you're adding quite a lot of weight to it that I just think is unnecessary and likely detrimental.
I've had these sliding blocks installed for going on a month of printing as of this posting, and my printer is busy for most of nearly every single day. So far these blocks have worked out great. Because the pads are designed to the exact dimension of the outer flat surface, and the V-slot itself, of the OpenBuilds V-Slot rails that the D-bot's framing is made of, they are a decently tight fit, and yet because they are printed from Igus's tribofilament, they will probably last forever, and show very low friction. It's not no friction, but the friction is surprisingly low for such full contact
My original idea for these used two shorter pads at either end of the sliding block, rather than a full-length pad, in order to minimize the surface contact area of the Igus material on the aluminum v-slot rail to drop friction even more, but it was more difficult than I'd assumed it would be to get all four pads (two each for top and bottom block per side) exactly aligned with each other. The full length pads fit down onto the tangs printed into the top surface of the blocks allowed extremely good alignment of the pads.
As printed, since I use a Bowden feed on my D-bot, I had slight blobbing at the corners that required a couple of minutes' worth of cleanup with an Xacto knife. Depending on how you print these, how the first layer goes down, etc. you may have to do some minor trimming to get the pads to snap down onto the tangs on the block. I left the tolerances extremely tight, tighter than you'd reasonably expect to achieve with a 3D print, specifically so that the pads would be exactly aligned on the bearing pads, and would be a good, tight fit in the v-slot slots.
Once printed and test fit to each other, I put a few drops of CA (super glue) onto the Igus filament pad bottoms, snapped them onto the blocks, and then clamped them down pretty hard onto a section of spare 2040 Vslot rail that I have left over from my D-bot. I left them clamped hard like this for a couple hours until I was sure the CA was dry.
I printed the blocks from PETG at 97% infill. I printed the pads from Igus tribofilament i170 at 70% infill with 3 perimeters in order to save material. I used 7 top layers at .1mm layer height, for fine resolution on the pads' bearing surfaces.
I've also tried the i180 filament. The 180 filament prints easier, and the prints look better, but it seems somehow softer than the 170, and the 170 also seems to have less friction. Igus claims in their marketing materials that 170 has the best wear behavior, but is more demanding of production technique. I can vouch for at least the second part of that.
I printed the Igus pads at 260 C with the bed at 90 C. I used a brim to lock it down after several attempts pealed up from my PEI sheet a little in one or two corners. I removed the brim with an Xacto knife afterward. I also used a brim on the main PETG blocks for the same reason.
This is version 1.0 of this item. My intent was to clean up the design of the blocks so they blend in better with the existing D-bot print carriage plates and the gantry bar end plates. I haven't done that refinement yet, but someone asked me for these files, so I'm putting it up now as is so they can be used. When I've refined the block design I'll post that updated block as 2.0. The change will only be cosmetic. While these blocks look fine as is, they can look better if I tweak the dimensions slightly and add a radius to the bottom ends of the block so they match the radius on the corners of the stock D-bot plates.
Here's a short Youtube video that I made showing this system in use on my D-bot:https://www.youtube.com/watch?v=ChPcBsqxBR4&feature=youtu.be
I'm attaching my SolidWorks 2016 source files for both blocks and pads. All of this is released with the Creative Commons - Attribution - Non-Commercial license.
Similar models
thingiverse
free
version 2.0 Igus-filament slider blocks/pads for D-Bot X/Y motion system by Rexipus
...s for the carrier blocks and the igus-filament pads, but also the solidworks parts files that these stl files are generated from.
thingiverse
free
Igus pad for narrow-slotted 2080 aluminum rails by arminj
...us filament slider blocks.
i've added a lower friction version with more "speed bars" and a carved out center area.
thingiverse
free
2040 V slot to 15mm Hiwin Bearing by Greg24
...pcs-block-carriage-hgw15cc-cnc/201419358641?rt=nc&_soffid=5018347904&_sofftype=ordersubtotaloffer&_trksid=p5731.m3795
thingiverse
free
PTFE PushFit Holder D-Bot by Buket0chicken
...chicken
thingiverse
ptfe push fit holder, mounted onto open builds v-slot rails. i'm using it on the back corner of my d-bot
thingiverse
free
D-bot rail kit 4020 by alexxkrotov
...iverse
this kit is designed for the v-slot 2040 profile, and the installation of linear guides min 12 h 400 mm for the x y axes.
thingiverse
free
Spacer Block (V-Slot) by Witali
...he rail 12mm so that you can run transmission components such as a belt drive or threaded rod underneath the v-slot gantry plate.
thingiverse
free
D-BOT - Rails - T-Slot - aluminum corners by ahntorage
...2020 piece instead of a 2040 for the x gantry.this is why there is no middle indent for the t-slot, so it would work with either.
thingiverse
free
V-Slot Internal Cable Clamps by dreadnought_strength
... of thingiverse came up with nothing suitable. this was for a d-bot, but it will obviously work on anything which uses this rail.
thingiverse
free
AM8 Z Axis Single Bearing by nullenvoid
...sier and removed some from the back so it didn't rub on the 2040 vertical extrusions.
mirror the part for the opposite side.
thingiverse
free
Hiwin EGR15R Stopper Mount by venuasg
...iverse
end stopper for hiwin egr14r rail which fits to 2020 04 2040 aluminium extrusion, very useful for corexy printer building
Tribofilament
thingiverse
free
igus bearing generator – fully customizable by igus
...iglidur i150 tribofilament. check this website for more information: www.igus.eu/tribofilament here are some tips how to use the "bearing-generator":...
thingiverse
free
drylin® bearing for 10 mm shafts; OD 19 mm by igus
...= 19 mm b = 29 mm (length) check www.igus.eu/tribofilament for more information about 3d-printing wear-parts check www.igus-cad.com for...
thingiverse
free
drylin® bearing for 8 mm shafts; OD 16 mm by igus
...= 16 mm b = 25 mm (length) check www.igus.eu/tribofilament for more information about 3d-printing wear-parts check www.igus-cad.com for...
thingiverse
free
drylin® bearing for 8 mm shafts; OD 15 mm by igus
...= 15 mm b = 24 mm (length) check www.igus.eu/tribofilament for more information about 3d-printing wear-parts check www.igus-cad.com for...
Rexipus
thingiverse
free
2020 extrusion overlapping corner bracket by Rexipus
...se corner brackets printed out in carbon fiber/petg. this is not necessary, but i wanted to try it out. it's extremely stiff.
thingiverse
free
remixed mount for LED strip by Rexipus
...d plate, this remix allows the led strip to intrude into my build space about a centimeter or so less than the original part did.
thingiverse
free
Cable chain anchor mounts for D-bot by Rexipus
... exact settings will be up to the individual and their printer to decide, but my recommendation is to make them stiff and strong.
thingiverse
free
Igus pad for narrow-slotted 2080 aluminum rails by arminj
...narrow-slotted 2080 aluminum rails by arminj thingiverse remix of rexipus#39; igus pads. the trapezoid block has been narrowed to...
thingiverse
free
XT60 heat plate mount for strain relief by Rexipus
... wants to fix or tweak this in whatever way.
edit 8 march 2017: just added step file versions of the sources for these two parts.
thingiverse
free
custom D-bot bottom corner by Rexipus
...rint them out and think about it and i'm sure it'll be pretty clear how to order the construction to make this work well.
thingiverse
free
D-bot stepper mounts with zip tie slots by Rexipus
...his however you would print the stock d-bot stepper mounts. i used petg, 100% infill, 260 c/70 c, on my d-bot, printed at 50mm/s.
thingiverse
free
D-Bot's Z axis setup using Igus-filament by 1sPiRe
...by 1spire thingiverse not tested cross over between the rexipus#39;s igus-filament sliders and my d-bot's z axis...
thingiverse
free
Mount for AC power plug and fuzed switch combo unit by Rexipus
...ended. i added 4mm to the interior cut to correct this. the back wall is now thinner, and the internal empty volume is increased.
thingiverse
free
Duet Wifi controller box attaches to 2020 extrusion by Rexipus
...to the control box, and to keep those wires separated by function at their entry into the box, four holes simply made more sense.
Igus
3d_export
$5
Christmas ball
...print, a christmas flower files types include: obj, 3dv, igus step and...
archive3d
free
Sconce 3D Model
...lantern
sconce igu wall up-down n040214 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
AC-DC power supply
...the marking on the top for printed circuit boards. igus and step file format for importing into ecad...
3d_export
$5
Picto toilet directions
...directions. include 3d files next to rhino6: x3dv, step, igus obj and stl. double-sided, flipping changes the gender directions...
3d_export
$5
LED Right Angled PCB Mounting
...3dexport right angled pcb mounting ø3.0mm led. step and igus files. multiple led colors: blue, purple, red, green, and...
3d_export
$5
USB Micro B connector
...usb mirco connector. two type of files step and igus for 3d import into ecad tools, pcb footprints. added...
thingiverse
free
LMH8LUU Igus style by NitzscheModellbau
...lmh8luu igus style by nitzschemodellbau
thingiverse
lmh8luu igus style
thingiverse
free
Printed Igus bushing by MikeDX
...gus bushings whilst building my prusa air, so i designed and printed these.
http://czechreprap.eu/reprap-parts/igus-bushing.html
thingiverse
free
igus slide by arbib
...igus slide by arbib
thingiverse
team 1577 frc
thingiverse
free
IGUS Bushing finishing tool by jpasternack
...igus bushing finishing tool by jpasternack
thingiverse
igus bushing finishing tool
Bot
turbosquid
$19
Bot
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Bot
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
scanner bot
...scanner bot
3dexport
cool scanner bot who scans for fixing things...
3d_ocean
$9
Apc Bot
...n bot games toys
an all-purpose-constructo-bot. for cartoon purposes. the model is not rigged. please use vray adv for rendering.
3d_export
$75
Bot 3D Model
...bot 3d model
3dexport
robot bot man kiborg character
bot 3d model evgen 19504 3dexport
turbosquid
free
Eye Bot
...eye bot
turbosquid
free 3d model eye bot for download as fbx on turbosquid: 3d models for games, architecture, videos. (1514059)
turbosquid
$29
Gorill-bot
...bosquid
royalty free 3d model gorill-bot for download as fbx on turbosquid: 3d models for games, architecture, videos. (1239456)
turbosquid
$25
Lamp Bot
...bosquid
royalty free 3d model lamp bot for download as blend on turbosquid: 3d models for games, architecture, videos. (1230121)
turbosquid
$10
Spectre Bot
...osquid
royalty free 3d model spectre bot for download as fbx on turbosquid: 3d models for games, architecture, videos. (1616378)
turbosquid
$8
Ultra Bot
...urbosquid
royalty free 3d model ultra bot for download as ma on turbosquid: 3d models for games, architecture, videos. (1330752)
Motion
3ddd
$1
Fabbian Motion
...motion
3ddd
fabbian , motion
светильник fabbian коллекция motion. текстурка в комплекте.
design_connected
$7
Motion Notion
...motion notion
designconnected
howard miller motion notion computer generated 3d model. designed by nelson, george.
turbosquid
$10
motion shark
...squid
royalty free 3d model motion shark for download as rib on turbosquid: 3d models for games, architecture, videos. (1261380)
3d_ocean
$6
Motion Set
...ng face and vertex, three file format are included,very useful for motion graphic artist , total poly 143.952 total vertex 79.952
3d_export
$10
Motion Tracker Aliens
...er out moving objects from stationary background and then displayed them on the monitor as a series of contours of probable loci.
3d_export
$6
motion stand for book and logo
...motion stand for book and logo
3dexport
motion stand for book and logo
turbosquid
$99
Planes of Motion Combo
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$50
Rotary-straight motion
...y-straight motion for download as 3ds, obj, fbx, 3dm, and skp on turbosquid: 3d models for games, architecture, videos. (1402602)
3d_export
$6
Reciprocating Motion
...#39;vinci's reciprocating motion contraption the model is used for picking up buckets of water from a well materials included
3d_export
$15
M314 Motion Tracker Aliens
...ng objects from stationary background and then displayed them on the m314's monitor as a series of contours of probable loci.
Pads
turbosquid
$15
Note Pad Writing Pad
...oyalty free 3d model note pad writing pad for download as max on turbosquid: 3d models for games, architecture, videos. (1309269)
3ddd
$1
Bed Padded
...bed padded
3ddd
padded bed , pixellin
padded bed , pixellin , bed 3d model
3d_export
$5
Padded stool
...padded stool
3dexport
padded stool
3d_export
free
Padded stool
...padded stool
3dexport
padded stool
3d_export
$5
pads
...pads
3dexport
3d_ocean
$2
mouse pad
...mouse pad
3docean
3d models computer electronics mouse
mouse pad 3d models. it’s mouse pad.
3d_export
$5
Padded stool
...padded stool
3dexport
leather padded stool on a metal base
3d_export
$5
Padded stool
...padded stool
3dexport
leather padded stool on a metal base.
3d_export
$8
Padded chair
...padded chair
3dexport
padded chair, black spout and light blue leatherette.
3d_export
$7
Padded Stool
...padded stool
3dexport
padded stool, black spout and light blue leatherette.
Linear
3ddd
$1
Linear Diffusers
...linear diffusers
3ddd
диффузор
set of linear diffusers for ceiling.
design_connected
$27
Linear Sofa
...linear sofa
designconnected
scp linear sofa computer generated 3d model.
design_connected
$18
Atlantis linear
...atlantis linear
designconnected
terzani atlantis linear pendant lights computer generated 3d model. designed by barlas baylar.
3d_export
$5
light linear unit
...light linear unit
3dexport
light linear unit
turbosquid
$5
Linear Actuator
...
royalty free 3d model linear actuator for download as blend on turbosquid: 3d models for games, architecture, videos. (1589061)
turbosquid
$29
Linear panel
...oyalty free 3d model linear panel for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1391254)
turbosquid
$12
Linear Chandelier
...y free 3d model linear chandelier for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1574289)
turbosquid
$10
Grohe Lineare
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Linear Axis
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Linear Unit 3D Model
...linear unit 3d model
3dexport
linear unit force torque velocity
linear unit 3d model fau 71218 3dexport
Guide
turbosquid
$15
Guide drawer
...squid
royalty free 3d model guide drawer for download as dwg on turbosquid: 3d models for games, architecture, videos. (1261387)
turbosquid
$1
Road Guide
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
archive3d
free
Guide-board 3D Model
...ion sign guide sign
guide-board n170112 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
turbosquid
$2
soap cutter guide
...
royalty free 3d model soap cutter guide for download as stl on turbosquid: 3d models for games, architecture, videos. (1694030)
turbosquid
$15
Blind Guiding tiles
...free 3d model blind guiding tiles for download as 3dm and dae on turbosquid: 3d models for games, architecture, videos. (1156598)
turbosquid
$69
Japanese Tour Guide
...d model japanese tour guide for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1614288)
turbosquid
$10
CNC Linear Guide
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Tank Model Guide
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Road Guide 2
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$9
Guide Books 3
...sformed separately and each have unique texture map on front and back cover. to make your work easier this model comes in thre...
Blocks
archibase_planet
free
Blocks
...blocks
archibase planet
blocks bricks toy
toy blocks - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
Block
...block
3dexport
3d_export
$10
The guillotine and the block
...the guillotine and the block
3dexport
the guillotine and the block autocad 2013
3d_ocean
$8
Concrete Blocks
... blocks, barriers or cover for characters during a fire fight. each one has its own diffuse map, specular and normal map in tg...
archibase_planet
free
Glass block
...glass block
archibase planet
glass block brick
glass block n211009 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$99
city block
...city block
3dexport
city block 3d model. include max, obj and fbx files.
3d_ocean
$3
Concrete Blocks Textures
...res
3docean
block blocks concrete seamless wall walls
a couple of seamless textures with two differents sizes of concrete blocks.
3d_export
$5
plummer block
...plummer block
3dexport
this is an 3d model of plummer block assembly where seven parts are required to assemble this.
design_connected
$16
Block 2
...block 2
designconnected
henry pilcher block 2 computer generated 3d model. designed by pilcher, henry.
3d_export
$7
concrete blocks on pallets
...concrete blocks on pallets
3dexport
concrete blocks on pallets, 3 types of blocks. there are all the necessary textures.
Y
turbosquid
$1
Tetera y Galletas y Caf
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Смеситель Y-CON
...смеситель y-con
3ddd
смеситель , y-con
смеситель y-con
3ddd
$1
Y-Chair
...y-chair
3ddd
tom dixon
y-chair designed by tom dixon,
3ds max + obj, corona
3ddd
$1
Y Chair compilation
....net/products/us/y-chair-sled-base
y chair swivel basehttp://www.tomdixon.net/products/us/y-chair-swivel-base
turbosquid
$190
Y-8
...y-8
turbosquid
royalty free 3d model y-8 for download as max on turbosquid: 3d models for games, architecture, videos. (1658891)
turbosquid
$7
Bench Y
...turbosquid
royalty free 3d model bench y for download as obj on turbosquid: 3d models for games, architecture, videos. (1488746)
turbosquid
$15
bonePile Y
...oyalty free 3d model bonepile y for download as blend and obj on turbosquid: 3d models for games, architecture, videos. (1546374)
turbosquid
$7
Y for Yarn
...d
royalty free 3d model y for yarn model for download as max on turbosquid: 3d models for games, architecture, videos. (1699732)
turbosquid
$2
FONT Y
...quid
royalty free 3d model font y for download as ma and obj on turbosquid: 3d models for games, architecture, videos. (1549457)
3ddd
$1
WOOD-y
...wood-y
3ddd
wooden guy
System
archibase_planet
free
System
...m
archibase planet
fire alarm system fire alarm box
security light system - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Spider system
...stem spider glass system
spider system to fix glass stefano galli n050912 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3ddd
$1
Euforia System
...euforia system
3ddd
euforia
euforia system
3d_export
$50
Roof system Truss system 3D Model
...oof system truss system 3d model
3dexport
roof system truss truss stage
roof system truss system 3d model aleksbel 38970 3dexport
3ddd
$1
DVD System
...dvd system
3ddd
dvd , schneider
dvd system
design_connected
free
Seating system
...seating system
designconnected
free 3d model of seating system
3d_export
$5
solar system
...solar system
3dexport
solar system in c4d, with 8k nasa textures
3ddd
$1
Quanta System
...quanta system
3ddd
медицина
quanta system.
лазерное оборудование для медицинских центров
3d_export
$15
solar system
...nd the other the sun, the earth and the moon, the latter has an animation with camera movement included, the files are in spanish
3d_export
$14
missile system
...missile system
3dexport
Made
design_connected
$11
Geometry Made Easy
...geometry made easy
designconnected
micromacro geometry made easy computer generated 3d model. designed by bernardi, sara .
turbosquid
$20
Loopa Bed by MADE
...
royalty free 3d model loopa bed by made for download as max on turbosquid: 3d models for games, architecture, videos. (1159987)
turbosquid
$10
MADE Barstool Sean
...
royalty free 3d model made barstool sean for download as max on turbosquid: 3d models for games, architecture, videos. (1564047)
turbosquid
$10
MADE Kitson Barstool
...oyalty free 3d model made kitson barstool for download as max on turbosquid: 3d models for games, architecture, videos. (1564045)
turbosquid
$10
MADE Rory chair
...id
royalty free 3d model made rory chair for download as max on turbosquid: 3d models for games, architecture, videos. (1563827)
turbosquid
$10
Toys made of wood
...
royalty free 3d model toys made of wood for download as max on turbosquid: 3d models for games, architecture, videos. (1329711)
turbosquid
$2
Shotgun made of bones
...yalty free 3d model shotgun made of bones for download as obj on turbosquid: 3d models for games, architecture, videos. (1689901)
3ddd
$1
Made In Ratio - Alpha Chair
...made in ratio - alpha chair
3ddd
made in ratio
the alpha chair by made in ratio.
fully unwrapped uvs.
turbosquid
$26
Sofa Made Hewitt
...ty free 3d model sofa made hewitt for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1398557)
turbosquid
$26
Sofa Made Julianne
... free 3d model sofa made julianne for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1397776)