Crickit standoff platform by computek45

...ckit with screws (with the cpx or feather screwed in) see the file with the name 'screw' in it. *was updated june 9, 2018

...ger standoffs are designed for the basher bad bug, and the smaller are extensions for the 1/16 short course truck from hobbyking.

...ector/platform print time: 10 minutes printing notes: printed this in petg, without supports. 0.1mm resolution, 75% infill. enjoy

...owforge laser pro cutter. the .svg file is attached. note: the triangle top point printed on the pad goes to the side with power.

...217 thingiverse this is a simple 20mm standoff that i am using with the dj105 quad copter. printed laying flat on the platform.

...ered by a power supply for constant usage. with 3d printed parts, electronics and hardware, you can create a lab shaker agitator.

...ttps://www.adafruit.com/product/3333 4 x aa battery holder with 2.1mm plug and on/off switchhttps://www.adafruit.com/product/3788

...m in existing design (which is too large for a cc3d). bolts via standoffs to apm platform. 2 shells 50% infill abs recommended.

...n to a minimum. it's a snug fit, but it works great on my shendrones shrieker. just used standoff mounts as if it were an fc.

... are mounted to the 3d printed enclosure. we used ninjaflex filament to 3d print watertight mounts for the motors and components!

...45 thingiverse made larger for mainstay 5' 11" floor lamp. i would suggest using a translucent filament for this print.

...ttps://www.adafruit.com/product/3333 4 x aa battery holder with 2.1mm plug and on/off switchhttps://www.adafruit.com/product/3788

...ered by a power supply for constant usage. with 3d printed parts, electronics and hardware, you can create a lab shaker agitator.

...ckit with screws (with the cpx or feather screwed in) see the file with the name 'screw' in it. *was updated june 9, 2018

...owforge laser pro cutter. the .svg file is attached. note: the triangle top point printed on the pad goes to the side with power.

... are mounted to the 3d printed enclosure. we used ninjaflex filament to 3d print watertight mounts for the motors and components!

...adafruit cricket. you will need to print one tabs for this design. it can be found at: https://www.thingiverse.com/thing:3401942

...ot sounds (10 bit 22.5 khz). my son wore it once to a theme birthday party but wants to go as a pirate on carnival instead. sigh.

...t be a good reason it's asymmetric, but it escapes us, and it makes building stuff for it that much more annoying. boo hiss.)

...extension first! detailed instructions on how to do that here:https://learn.adafruit.com/adafruit-crickitcreative-robotic-interactive-construction-kit?view=all#adding-crickit-extension electronics used:https://www.adafruit.com/product/3333https://www.adafruit.com/product/3093https://www.adafruit.com/product/169https://www.adafruit.com/product/276https://www.adafruit.com/product/592 full instructions for assembly and use available...

...20x20 standoff thingiverse standoff for 8mm linear rails. standoff distance 20mm

...standoff by charlespax thingiverse this is a standoff created to hold up a friend's monitor.

...standoff holder by jfaller thingiverse holder for for m3x6 standoff.

...odore 64. cut off old standoffs, sand smooth then attach these standoffs with epoxy. be sure to align with the holes in the case.

...bts7960 standoff by albatito thingiverse standoff for bts7960. m3 hardware

...of the quad copter, but without the standoffs and with 3mm holes below where the standoffs were. requested by fb user ian paine.

...doff by maxharrison thingiverse this is a motherboard standoff that is designed to be positioned into place and then glued down.

...standoff capacitor holder thingiverse 25v/35v standoff capacitor holder. fits a 13mm capacitor.

...printbed standoff feet by shawdreamer thingiverse standoffs

...standoff by intijk thingiverse 12 + 4 mm height

...platform by jlip36 thingiverse platform

...rock platform thingiverse floating rock platform (wip)

...platform by sobebucks thingiverse this is to add a third platform for a dji flamewheel kit.

...platform by broadzilla00 thingiverse needed an extention/platform to help hold my auto fish feeder. work in progress.

...platform rails thingiverse 1 inch rail segments that can be glued down to catwalks and platforms for industrial style terrain.

...platform test by aking99999 thingiverse platform test.

...platform and pole by leitz thingiverse attached pole to platform

...16x16 platform by minimicrofpv thingiverse small 16x16 platform for things

...platforms for rodents by jagang thingiverse two platforms for rodent cage.

...u want us to upgrade anything :). if you want to see it running on a video, you can go to our instagram profile @celda3d. enjoy!!