CR8可調式光學限位座 by myunming

...ailable dimensions are : m3 x 4 / m3 x 5 / m3 x 6 / m3 x 8 / m3 x 10 / m3 x 13 / m3 x 16 / m3 x 20 / m3 x 25 / m3 x 30 / m3 x 40

...mesa gamer m3 3dwarehouse mesa gamer m3 mesa gamer m3 mesa gamer m3

...m3 submachine gun (m3 grease gun) 3dwarehouse m3 submachine gun #gun #m3 #m3_submachine_gun

...m3 grease gun 3dwarehouse m3 grease gun #m3

...m3 slices (2) by keyx90 thingiverse m3 slices, for m3 bolts.

...knob m3 by mrstanlez thingiverse knob for m3 screw and/or m3 nut.

...carrosseriering-m3 3dwarehouse carrosseriering din9021 m3 #carrosseriering #din9021 #m3

...m3 grabcad m3

...m3 3dwarehouse an m3

...m3s 3dwarehouse m3s

...cr8平台調整旋鈕(m4) by myunming thingiverse cr8平台調整旋鈕(m4)

...風速計 by myunming thingiverse 608軸承x2 指針支架下方開孔5mm可拆下分開使用。 勺子支架下方開孔6mm可插入竹筷或營柱。 ps.利用熱水將勺子扭轉90度。

...cr8 可拆式環狀風罩 by myunming thingiverse cr8可拆式環狀風罩.附上兩種風罩可替換

...ing thingiverse 鋁製軌道1(長度自訂) (厚9.3mm，導軌底寬19mm，導軌槽上寬8.4mm，導軌槽下寬14.3mm。) m6-公2(10公分) m6-公1(5公分) m6-母4(頂針要鎖2才不會轉動) m4-公2(2cm) m4-母*2

...53mm (h=53mm)<br>- the size of castle : 195x46x41mm (h=41mm)<br>- the size of assembly (castle + house) : 195x51x80mm

...cr8 可拆式環狀風罩 by myunming thingiverse cr8可拆式環狀風罩.附上兩種風罩可替換

...because my print bed has already changed, i'm not sure the height is low enough for the original bed. if not, please tell me.

...cr8平台調整旋鈕(m4) by myunming thingiverse cr8平台調整旋鈕(m4)

...stl －－底部鋁擠角腳墊(建議用軟料列印，需配合m6內六角螺絲) t-2200-022-lcd.stl ＝＝12864 掀蓋式面板 t-2200-023-lcd.stl －－掀蓋式面板 磁鐵座 t-2200-024-lcd.stl＝＝掀蓋式面板 檔塊

...cr8-cablechain-by shiung by shiung0202 thingiverse cr8 using. no support 100% infill 0.4mm extruder 0.15mm layer

...義式咖啡機填粉器專用座 by smat6177 thingiverse 義式咖啡機填粉器專用座

... 70% to tmc2100 ,but it pn;y give the wind to the x y step motor,if you change 3 or 4 step motor,this design can't work well.

...xyz限位，xy调平 by nnjs thingiverse 这是那年九岁的um打印机第一次更新！ 1.xyz轴限位开关重新画图，更简单更简便！ 2.xy轴简易调平。 没有啦—— 详情见酷安@那年九岁 意见建议一定要联系我