GrabCAD
Concept_One
by GrabCAD
Last crawled date: 1 year, 10 months ago
A little bit of explanation…
Casing for cell
Outer walls are 4mm thick while the one’s inside are 3mm. Batteries are tightly fixed between the walls with possibility to rotate them as the wiring will dictate.
On four inner corners I left holes for casing attachment, distance between them (on the smaller side of case) corresponds to corrugated roof panels (if the ones that others are using in this challenge are actually being used). If not – there are four holes outside of the case. However, I think that no matter which model will win, who ever will be installing this he will probably bolt our casing to whatever piece of sheet metal he can find… if he has a piece of roof panel even better.
Cell is fixed with 2mm flange from three corners via top of the case (0.1 spacing between cell and top of the case) and even if it has usable surface all over it still covers only 0.05% of it. I left a 1mm gap in the middle of bottom case walls (as shown on one of the pics) so that even if some water leaks it would still go through that gaps all the way out. Have in mind that case is tilted due to roof so the water will slide. That’s why there is no wall around the bottom of the solar cell. A small amount of silicon can be used along the edges but maybe there is no need. Case lid (top) is screwed with two M4 12mm socket head screws.
Casing should be white or with some similar but light reflecting color because solar cell are way more effective if they are cooler. That’s why casing should have some holes so the air can flow
Casing for LED
Everything is made with clear plastic. It would be nice if even bottle caps are made the same way so that water can receive more light during day time. Cap and the tube inside are in one piece and they are hollow all the way for easy access to diodes and cable routing. Whole thing is protected from water by another cap that is placed and rotated on top of the bottle (there is enough room for cables)
If I have time I’ll design another way of led positioning were they are placed to the side as well. Same goes to rendering where the whole thing is fixed to the roof...
Like if you like :)
Casing for cell
Outer walls are 4mm thick while the one’s inside are 3mm. Batteries are tightly fixed between the walls with possibility to rotate them as the wiring will dictate.
On four inner corners I left holes for casing attachment, distance between them (on the smaller side of case) corresponds to corrugated roof panels (if the ones that others are using in this challenge are actually being used). If not – there are four holes outside of the case. However, I think that no matter which model will win, who ever will be installing this he will probably bolt our casing to whatever piece of sheet metal he can find… if he has a piece of roof panel even better.
Cell is fixed with 2mm flange from three corners via top of the case (0.1 spacing between cell and top of the case) and even if it has usable surface all over it still covers only 0.05% of it. I left a 1mm gap in the middle of bottom case walls (as shown on one of the pics) so that even if some water leaks it would still go through that gaps all the way out. Have in mind that case is tilted due to roof so the water will slide. That’s why there is no wall around the bottom of the solar cell. A small amount of silicon can be used along the edges but maybe there is no need. Case lid (top) is screwed with two M4 12mm socket head screws.
Casing should be white or with some similar but light reflecting color because solar cell are way more effective if they are cooler. That’s why casing should have some holes so the air can flow
Casing for LED
Everything is made with clear plastic. It would be nice if even bottle caps are made the same way so that water can receive more light during day time. Cap and the tube inside are in one piece and they are hollow all the way for easy access to diodes and cable routing. Whole thing is protected from water by another cap that is placed and rotated on top of the bottle (there is enough room for cables)
If I have time I’ll design another way of led positioning were they are placed to the side as well. Same goes to rendering where the whole thing is fixed to the roof...
Like if you like :)
Similar models
grabcad
free
Ain't no sunshine
...description of casing for solar panel is pretty much similar as in my previous model concept_one so it’s just...
grabcad
free
Solar LED bottle
...- top housing hole
solar panel - top housing recess
top housing walls - roofing patch
solar panel roof patch unit - existing roof
thingiverse
free
Bottle Cap Case by sthane
...or pbr bottle caps, i sized it to hold 13, so i could print one for each suit.
update 11/13/20: i added a stand to stack 4 cases.
thingiverse
free
Bottle cap leak fix by tatou100
...softdrink bottle. so i design this piece that can be epoxy glued inside the cap. hence forcing droplet to fall inside the bottle.
thingiverse
free
Pill Bottle Rack (Walgreens 32mm) by mrflippant
...utton release to unscrew the container from the cap. cool, huh?
requests for variants and constructive feedback are both welcome!
grabcad
free
Roof light
...tightened which pulls the assembly down... sealing the joint. similary the cell cover is sealed with joint sealant. ah,...
thingiverse
free
2 inch dock pipe cap by Schmoogli
...e since the other end of the pipe is in the water.
if he likes it, i will outfit all the dock support pipes with solar lights :-)
3dwarehouse
free
solar roof
...ehouse
integrated roof with cell product and water recycle for one use #cbastien_rajaona #eco #house #madagascar #recycle #water
grabcad
free
EN3D Bottle Light 3
...the only thing what will happen is that the battery-unit is mounted a little bit higher or lower (depending of the grooves depth)
thingiverse
free
Plastic Bottle Opener by natpie
... if your only opening water bottles the water bottle version seems to grip just a little better than the plastic bottle version.
Concept
3d_export
$5
concept house
...concept house
3dexport
concept house blend.
turbosquid
$20
concept
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
concept
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Concept
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Concept
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Bo concept
...bo concept
3ddd
boconcept , декоративный набор
bo concept
3d_ocean
$45
Dreamcar concept
...cept cars from the past.before i became 3d modeler i sketched a lot futuristic cars.when i want it to look more realistic,i st...
3d_ocean
$49
Buggy Concept
... poly massive outdoor robust vehicle
just a model of are own buggy concept vehicle. maybe you can make a beautiful renders of it!
3d_export
free
concept s ii
...concept s ii
3dexport
concept car
3d_export
free
concept s iii
...concept s iii
3dexport
concept car
One
turbosquid
$2
one plus one
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
One
...one
3ddd
стул
офисный стул one
3ddd
free
one
...
palazetti one ,http://palazzetti.ca/index.php/component/virtuemart/seating/armchairs-lounges/one-chair-detail?itemid=0
turbosquid
$35
One A
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
One
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Стул One
...стул one
3ddd
one , magis
кресло magis s.p.a , one
3ddd
$1
Стул One
...стул one
3ddd
one , magis
кресло one chair (4star), magis s.p.a.
3d_export
$20
xbox one
...xbox one
3dexport
xbox one
3ddd
$1
xbox one
... консоль , джойстик
xbox one + kinect + gamepad
3ddd
free
One
...nstantin grcic
артикул ct-284 (cosmorelax.ru)
размер l36xw41xh82.5, sh 77cm
цвет черный, красный
материал алюминий
вес 2,5 кг