Thingiverse
cESPER - a Carbine length ESPER by boont
by Thingiverse
Last crawled date: 3 years, 4 months ago
Introducing the cESPER, a carbine length ESPER.
Features:
*The cESPER has an overall length of 650mm to the front of the muzzle. The pictured blaster has a 400mm (16") barrel bringing the total length to 800mm.
*****Easily prime over 200fps!**
*Pump grip that fits to the standard caliburn priming bars.
*Standard Caliburn rear end or the adjustable stock.
*Caliburn thumbhole stock or other cosmetic stocks
*8mm Pull Guide Rail for ease (Note no longer top prime-able)
You will need the following hardware for this blaster.
1) 3x 630mm 3/16" or M5 Threaded Rod.
2) 8mm tube: 1x 210mm, 2x 281mm
3) Caliburn prime bars, 1 pair.
4) 7x 3/16" BSW or M5 nuts.
5) 1x 3/16" or M5, 1/4" or 8mm or 10mm length screw (muzzle pinch)
6) 1x self tapping M3, 10mm
7) Hardware as required for caliburn standard stock or adjustable stock.
8) suggest you use spring washers on the threaded rods.
Parts labelling:
"F" Front
"R" Rear
"O" Optional
Front (Required):
barrelrail - front rail, notched for alignment
frontmuzzle - front muzzle, notched for alignment
pumpgrip - pump grip. Dual M5 sized screw holes for stability.
dartjam - notched for rail alignment. This has nut slots for 3/16" BSW if you want to use two pieces of threaded rod. Front: ~230mm (280mm w/ front ext) Rear: ~360mm. If you don't want to print this, shave off the alignment notch on barrelrail AND the original lower rail guide so you don’t crush your fingers when you prime .
Rear (Required):
endcap - inner endcap with short rail section
endloop - outer endloop file with extension for stock
pull - plungertube pull with picatinny rail stripped off
rearrail - additional section of picatinny rail behind the endcap
IMPORTANT: THIS PIECE IS IMPORTANT. IF YOU DON'T PRINT THIS, YOU WILL SLAM THE PULL INTO YOUR FACE AND PINCH YOUR CHEEK. IT HURTS.
tcb-cheekrest - modified from EnderSavesTheDay's file - added a screw hole if you need to slide it around. This piece slides over the endcap/rearrail picatinny sections.
Optional:
muzzle - this is the esper muzzle not the front muzzle. It has nut slots for 3/16" BSW if you want to use two pieces of threaded rod. Front: ~210mm (260mm), Rear: ~410mm
barrelrail-extension - this is an additional 49mm of front rail if you want some more length. You will need to extend your threaded rod appropriately
ABackButt-flat - this is the Caliburn adjustable stock with the dart guide post cut off.
sealedrambase - this is the rambase with material added to stop it leaking
Included, but not modified from original files:
FrontButt8 - Required for the stock.
AButtPlate - curved rear butt
AStock3 - adjustable stock plate.
Assembly notes:
NOTE: FILES ARE NOT ORIENTED FOR PRINTING
1) You will need to drill out and tap the single-hole end to M5, 3/16", #10-24, whatever.
2) The prime grip has a second hole for stability if you wish. Recommended for band loads > 150fps
3) If you don't want to stick extra long threaded rods in, print the optional parts
4) If you want a longer front, you can print the extension bit. Note that this, along with the dartjam, frontrail and the muzzle are all notched. You will also need longer 8mm guide tubes.
5) 8mm tubes are the same that you use for a caliburn/talon claw/etc. Highly suggest you use a metal or carbon tube for the rear guide. The nylon tube is ever so slightly squishy
6) You MUST print the cheekrest, or replace it with something similar.
7) The rear section will accept standard caliburn cosmetic stocks or the thumbhole stock.
8) If you don't want the adjustable stock, you could leave Astock3 out and just bolt Abuttplate to ABackButt-flat
9) You can use either a caliburn or a talon claw ram. Which you choose may depend on your barrel. If you use a MM barrel with the milled dart chamber, suggest you use the talon claw ram. A caliburn ram gives a smoother and stronger prime.
10) You'll probably need a sight riser
Features:
*The cESPER has an overall length of 650mm to the front of the muzzle. The pictured blaster has a 400mm (16") barrel bringing the total length to 800mm.
*****Easily prime over 200fps!**
*Pump grip that fits to the standard caliburn priming bars.
*Standard Caliburn rear end or the adjustable stock.
*Caliburn thumbhole stock or other cosmetic stocks
*8mm Pull Guide Rail for ease (Note no longer top prime-able)
You will need the following hardware for this blaster.
1) 3x 630mm 3/16" or M5 Threaded Rod.
2) 8mm tube: 1x 210mm, 2x 281mm
3) Caliburn prime bars, 1 pair.
4) 7x 3/16" BSW or M5 nuts.
5) 1x 3/16" or M5, 1/4" or 8mm or 10mm length screw (muzzle pinch)
6) 1x self tapping M3, 10mm
7) Hardware as required for caliburn standard stock or adjustable stock.
8) suggest you use spring washers on the threaded rods.
Parts labelling:
"F" Front
"R" Rear
"O" Optional
Front (Required):
barrelrail - front rail, notched for alignment
frontmuzzle - front muzzle, notched for alignment
pumpgrip - pump grip. Dual M5 sized screw holes for stability.
dartjam - notched for rail alignment. This has nut slots for 3/16" BSW if you want to use two pieces of threaded rod. Front: ~230mm (280mm w/ front ext) Rear: ~360mm. If you don't want to print this, shave off the alignment notch on barrelrail AND the original lower rail guide so you don’t crush your fingers when you prime .
Rear (Required):
endcap - inner endcap with short rail section
endloop - outer endloop file with extension for stock
pull - plungertube pull with picatinny rail stripped off
rearrail - additional section of picatinny rail behind the endcap
IMPORTANT: THIS PIECE IS IMPORTANT. IF YOU DON'T PRINT THIS, YOU WILL SLAM THE PULL INTO YOUR FACE AND PINCH YOUR CHEEK. IT HURTS.
tcb-cheekrest - modified from EnderSavesTheDay's file - added a screw hole if you need to slide it around. This piece slides over the endcap/rearrail picatinny sections.
Optional:
muzzle - this is the esper muzzle not the front muzzle. It has nut slots for 3/16" BSW if you want to use two pieces of threaded rod. Front: ~210mm (260mm), Rear: ~410mm
barrelrail-extension - this is an additional 49mm of front rail if you want some more length. You will need to extend your threaded rod appropriately
ABackButt-flat - this is the Caliburn adjustable stock with the dart guide post cut off.
sealedrambase - this is the rambase with material added to stop it leaking
Included, but not modified from original files:
FrontButt8 - Required for the stock.
AButtPlate - curved rear butt
AStock3 - adjustable stock plate.
Assembly notes:
NOTE: FILES ARE NOT ORIENTED FOR PRINTING
1) You will need to drill out and tap the single-hole end to M5, 3/16", #10-24, whatever.
2) The prime grip has a second hole for stability if you wish. Recommended for band loads > 150fps
3) If you don't want to stick extra long threaded rods in, print the optional parts
4) If you want a longer front, you can print the extension bit. Note that this, along with the dartjam, frontrail and the muzzle are all notched. You will also need longer 8mm guide tubes.
5) 8mm tubes are the same that you use for a caliburn/talon claw/etc. Highly suggest you use a metal or carbon tube for the rear guide. The nylon tube is ever so slightly squishy
6) You MUST print the cheekrest, or replace it with something similar.
7) The rear section will accept standard caliburn cosmetic stocks or the thumbhole stock.
8) If you don't want the adjustable stock, you could leave Astock3 out and just bolt Abuttplate to ABackButt-flat
9) You can use either a caliburn or a talon claw ram. Which you choose may depend on your barrel. If you use a MM barrel with the milled dart chamber, suggest you use the talon claw ram. A caliburn ram gives a smoother and stronger prime.
10) You'll probably need a sight riser
Similar models
thingiverse
free
Caliburn 180 Choker Muzzle remix
...s an export from a middle step to adapt a frontline foam 509 barrel adaptor.
may require modification to your priming rod length.
thingiverse
free
No Shriek Noise Printed Caliburn Stock Spacer Tubing by racerethan
...e useful for this.
friction fits in the printed stock spacer.
tube is mcmaster part #8585k207, same as the caliburn plunger tube.
thingiverse
free
Talon Claw U Bullpup RMAX 1 with Caliburn U rails by c5k0
...ell -- added extra material to keep the alignment true along the u channels - and also includes pin holes for top rail alignment.
thingiverse
free
Talon Claw and Talon Claw U Caliburn Back End Parts by racerethan
... as far back.
-requires a stock spacer tube
-use the talon claw plungers not the full length plunger, it will jam on these prints
thingiverse
free
Simplified Caliburn U Plunger Tube Cover by Puredeath
...plified caliburn u plunger tube cover by puredeath
thingiverse
removed the rear section of rail completely and most of the front
thingiverse
free
6" Fin alignment guide by 16wbrinkley
...6" fin alignment guide by 16wbrinkley
thingiverse
fits 6" fiberglass tubing and 3/16" fins.
thingiverse
free
Aeon Pro Carbine Kit by shoelesshistorian
... just glues on.
supports needed only on the pumpslide parts- they will need to be printed diagonally standing so as not to crack.
thingiverse
free
Caliburn Carbine U Front Magwell by racerethan
... position for a caliburn carbine u.
u-channel lengths for a caliburn carbine u is in-between a caliburn and tc with stock length.
thingiverse
free
Fake 80mm laser tube by drandolph
...fake 80mm laser tube by drandolph
thingiverse
i use these to align my laser tube with 8mm threaded rod to show the beam path.
thingiverse
free
Caliburn U Stock Spacer Tube Extended Length by racerethan
...n u.
remix of https://www.thingiverse.com/thing:3105159 since thingiverse is busted af and won't let me list this as a remix.
Esper
thingiverse
free
Esper muzzle by CowboyCrusader
...sper with the cosmetic teeth things. aswell as this the sloped underside of the muzzle acts as a very comfortable makeshift grip.
thingiverse
free
Custom Keyblade (Esper) by CapnMyCapn
...custom keyblade (esper) by capnmycapn
thingiverse
custom keyblade i designed named esper keyblade
thingiverse
free
Esper muzzle by CowboyCrusader
...ft grip as it has a sloped underside which is much more comfortable to grip compared to other places on the front of the blaster.
free3d
free
Elsword - Diabolic Esper's Dynamos
...elsword - diabolic esper's dynamos
free3d
thingiverse
free
ESPERS DESK PLAQUE by chris33
...e attribute and being able to proof of work.
i have put the full model and the stl files to make the lettering and logo in colour
3dbaza
$2
Pendant Esper 03 (343429)
...6.29<br>xform: no<br>box trick: no<br>model parts: 2<br>render: v-ray<br>formats: 3ds max 2014, obj
thingiverse
free
C ESPER Endcap Alternative by racerethan
...ndcap alternative by racerethan
thingiverse
an alternative endcap for the cesper parts so i don't have to change the e-pull.
thingiverse
free
Worker PDW Stock Adapter for ESPER by EnderSavesTheDay
...-24 which you can find more readily at hardware suppply stores) threaded rod and cover with nuts to install this cosmetic add-on.
thingiverse
free
hot rod by cinderjanus
...rod by cinderjanus thingiverse es un muy simple trabajo, esper les...
Carbine
3d_ocean
$15
M4 Carbine
...carbine gun pistol rifle weapon
m4 carbine lowpoly game ready model 4096x and 2048x textures moving parts mag and bullet included
3d_export
$10
Carbine 3D Model
...carbine 3d model
3dexport
carbine rifle old weapon guns
carbine 3d model babycake 55054 3dexport
turbosquid
free
M1 carbine
...bine
turbosquid
free 3d model m1 carbine for download as fbx on turbosquid: 3d models for games, architecture, videos. (1650978)
turbosquid
$50
M4A1 CARBINE
...squid
royalty free 3d model m4a1 carbine for download as obj on turbosquid: 3d models for games, architecture, videos. (1421798)
turbosquid
$6
M1 CARBINE
...bosquid
royalty free 3d model m1 carbine for download as jpg on turbosquid: 3d models for games, architecture, videos. (1310947)
turbosquid
$6
M1 CARBINE
...bosquid
royalty free 3d model m1 carbine for download as jpg on turbosquid: 3d models for games, architecture, videos. (1310946)
turbosquid
$45
m1 carbine
...
royalty free 3d model m1 carbine for download as lwo and fbx on turbosquid: 3d models for games, architecture, videos. (1397666)
turbosquid
$25
M1 carbine
...ty free 3d model m1 carbine for download as 3ds, max, and obj on turbosquid: 3d models for games, architecture, videos. (1253775)
turbosquid
$80
M4 Carbine
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$35
M4A1 CARBINE
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Length
turbosquid
$3
Length limitroadsign
...gth limitroadsign for download as 3ds, dae, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1532908)
turbosquid
$5
Pharaoh with half-length column
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Screw M4 Length 20 mm
...ee 3d model screw m4 length 20 mm for download as obj and stl on turbosquid: 3d models for games, architecture, videos. (1676648)
turbosquid
$1
Screw M4 Length 10 mm
...ee 3d model screw m4 length 10 mm for download as stl and obj on turbosquid: 3d models for games, architecture, videos. (1556125)
turbosquid
$1
Screw M2 Length 20 mm
...ee 3d model screw m2 length 20 mm for download as stl and jpg on turbosquid: 3d models for games, architecture, videos. (1555504)
turbosquid
$1
Screw M2 Length 18 mm
...ee 3d model screw m2 length 18 mm for download as stl and obj on turbosquid: 3d models for games, architecture, videos. (1555498)
turbosquid
$1
Screw M2 Length 16 mm
...ee 3d model screw m2 length 16 mm for download as stl and obj on turbosquid: 3d models for games, architecture, videos. (1555330)
turbosquid
$1
Screw M2 Length 14 mm
...ee 3d model screw m2 length 14 mm for download as stl and obj on turbosquid: 3d models for games, architecture, videos. (1555163)
turbosquid
$1
Screw M2 Length 12 mm
...ee 3d model screw m2 length 12 mm for download as stl and obj on turbosquid: 3d models for games, architecture, videos. (1555112)
turbosquid
$1
Screw M2 Length 10 mm
...ee 3d model screw m2 length 10 mm for download as stl and obj on turbosquid: 3d models for games, architecture, videos. (1555040)