Cults
Calvin
by Cults
Last crawled date: 6 years, 2 months ago
Calvin, from the comic strip by Bill Watterson.
The comic strip Calvin and Hobbes follows the humorous antics of Calvin, a precocious, mischievous and adventurous six-year-old boy, and Hobbes, his sardonic stuffed tiger.
The full model is built using individual models of Calvin and Hobbes, therefore I created three separate Cults3D uploads:
For the final build using the individual Calvin and Hobbes models see:
https://cults3d.com/en/various/calvin-and-hobbes
For the Calvin model see:
https://cults3d.com/en/various/calvin (this upload)
For the Hobbes model see:
https://cults3d.com/en/various/hobbes
The fully completed model is 250mm tall after assembly.
Note: Calvin is 120mm tall and is designed to fit into the log from the final build. His foot is flat on the bottom and he can stand by himself but is not very stable without the log.
Enjoy!
------------------------------------------------------------------
Print Settings
Printer:
FlashForge Creator X
Rafts:
Doesn't Matter
Supports:
No
Resolution:
.2mm
Infill:
10%
-------------------------------------------------
Building the model
Colors (there are no multiple printed pieces)
Yellow:
c_hair
..
Flesh (I use beige):
c_face
c_face_bottom
c_arm_left
c_arm_right
..
White:
c_shoe_left
c_shoe_right
..
Orange:
c_shirt_left
c_shirt_middle
c_shirt_right
..
Black:
c_pants
c_eye_left
c_eye_right
c_mouth
c_stripe_1 though c_stripe_9
..
Any color (hidden connectors)
c_face_bump
c_body_bump
---------------------------------------------------
Printing and assembly tips
1-No supports are required.
..
2-The stripes are designed to be a single layer thickness of .2mm, or less as long as they print solid on your machine.
..
3-Be sure to clean any first layer squish if you have any problem joining parts. The parts should fit nicely when printed cleanly.
..
Assembly tips:
-'Stripes! There had to be stripes!' I avoided creating this model for quite some time due to the stripes. I finally settled on a design:
. The stripes are printed flat, one layer high
. The parts that the stripes are glued to contain indents for stripe placement.
. Most of the stripes are slightly curved to help wrap around the surface.
-*Important: To make it simpler to glue flat stripes to a round surface, take a moment to curl the stripes like you would with a piece of ribbon. Using a flat edge, pull the stripe along the edge to make it curl. Pay special attention to the very ends and ensure the ends curl.
-Test the length of each stripe before gluing, due to printer differences, stripes may need to be trimmed a bit.
-Optionally, instead of using the 3D printed stripes, the stripes can be painted on using the indents as a guide.
-The diagram below will help in assembling the model and is quite straightforward.
-The model is meant to be glued together. I use E6000 glue. It is a nice clear tacky glue allowing for easy part positioning. The longer you let it sit before joining parts, especially for the stripes, the tackier it gets until it fully sets.
-The Calvin model fits the log using the Cults3D links provided in the introduction.
The comic strip Calvin and Hobbes follows the humorous antics of Calvin, a precocious, mischievous and adventurous six-year-old boy, and Hobbes, his sardonic stuffed tiger.
The full model is built using individual models of Calvin and Hobbes, therefore I created three separate Cults3D uploads:
For the final build using the individual Calvin and Hobbes models see:
https://cults3d.com/en/various/calvin-and-hobbes
For the Calvin model see:
https://cults3d.com/en/various/calvin (this upload)
For the Hobbes model see:
https://cults3d.com/en/various/hobbes
The fully completed model is 250mm tall after assembly.
Note: Calvin is 120mm tall and is designed to fit into the log from the final build. His foot is flat on the bottom and he can stand by himself but is not very stable without the log.
Enjoy!
------------------------------------------------------------------
Print Settings
Printer:
FlashForge Creator X
Rafts:
Doesn't Matter
Supports:
No
Resolution:
.2mm
Infill:
10%
-------------------------------------------------
Building the model
Colors (there are no multiple printed pieces)
Yellow:
c_hair
..
Flesh (I use beige):
c_face
c_face_bottom
c_arm_left
c_arm_right
..
White:
c_shoe_left
c_shoe_right
..
Orange:
c_shirt_left
c_shirt_middle
c_shirt_right
..
Black:
c_pants
c_eye_left
c_eye_right
c_mouth
c_stripe_1 though c_stripe_9
..
Any color (hidden connectors)
c_face_bump
c_body_bump
---------------------------------------------------
Printing and assembly tips
1-No supports are required.
..
2-The stripes are designed to be a single layer thickness of .2mm, or less as long as they print solid on your machine.
..
3-Be sure to clean any first layer squish if you have any problem joining parts. The parts should fit nicely when printed cleanly.
..
Assembly tips:
-'Stripes! There had to be stripes!' I avoided creating this model for quite some time due to the stripes. I finally settled on a design:
. The stripes are printed flat, one layer high
. The parts that the stripes are glued to contain indents for stripe placement.
. Most of the stripes are slightly curved to help wrap around the surface.
-*Important: To make it simpler to glue flat stripes to a round surface, take a moment to curl the stripes like you would with a piece of ribbon. Using a flat edge, pull the stripe along the edge to make it curl. Pay special attention to the very ends and ensure the ends curl.
-Test the length of each stripe before gluing, due to printer differences, stripes may need to be trimmed a bit.
-Optionally, instead of using the 3D printed stripes, the stripes can be painted on using the indents as a guide.
-The diagram below will help in assembling the model and is quite straightforward.
-The model is meant to be glued together. I use E6000 glue. It is a nice clear tacky glue allowing for easy part positioning. The longer you let it sit before joining parts, especially for the stripes, the tackier it gets until it fully sets.
-The Calvin model fits the log using the Cults3D links provided in the introduction.
Similar models
cults
free
Calvin and Hobbes
...in the pictures section will help in assembling the model and is quite straightforward.
-the model is meant to be glued together.
cults
free
Hobbes
...pes, the tackier it gets until it fully sets.
-the hobbes model fits the log using the cults3d links provided in the introduction
cults
free
Charlie Brown
...hand were it touches the stripe.
5-refer to the assembly diagram for putting the model together. the model is meant to be glued.
cults
free
Dogbert
...nto the notch on the body above the nose and glued them into the glasses_arms. it all turned out quite simple to glue into place.
cults
free
Wally
...y previous models, you know who you are!). all parts should fit nicely and the only cleanup should be on the first layer, if any.
cults
free
Rat
...irst glance it seems awkward.
-the model stands nicely on it's own, however a base is included for extra stability if needed.
cults
free
George Jetson
...hile putting the model together.
6-refer to the assembly diagram for putting the model together. the model is meant to be glued.
cults
free
Snoopy
...itioning of the text characters.
3-refer to the assembly diagram for putting the model together. the model is meant to be glued.
cults
free
Barney Rubble
...he head to for full alignment.
..
2-refer to the assembly diagram for putting the model together. the model is meant to be glued.
cults
free
Linus van Pelt
...printer bed, you need to curl each individual hair similar to how you would curl a ribbon. be sure...
Calvin
cults
free
Calvin and Hobbes
...in the pictures section will help in assembling the model and is quite straightforward.
-the model is meant to be glued together.
cults
free
Hobbes
...hobbes models see: https://cults3d.com/en/various/calvin-and-hobbes for the calvin model see: https://cults3d.com/en/various/calvin for the hobbes model see: https://cults3d.com/en/various/hobbes (this upload) the...
Hobbes
cults
free
Calvin and Hobbes
...in the pictures section will help in assembling the model and is quite straightforward.
-the model is meant to be glued together.
cults
free
Hobbes
...pes, the tackier it gets until it fully sets.
-the hobbes model fits the log using the cults3d links provided in the introduction
Comics
cults
free
comic dog belgium
...comic dog belgium cults belgium comics dog tintin snowy milou personnel works with...
cults
free
Comic Book Tabs
...comic book tabs cults comics comic_books dc_comics marvel_comics the abc tabs are the same...
cults
$3
Dory 3D Comic Fish
... the color information like you see on the photos. dory consists of 2 parts. once the comic fish and the second part is the base.
cults
free
Pickles - comic strip scene
...included below.
the completed model after assembly is 128mm x 189mm x 203mm high and none of the parts require supports!
enjoy!
cults
free
Magnet Tintin et Milou
...magnet tintin et milou cults belgium comics tintin best hero from belgium...
cults
free
Logo Flash!
...logo flash! cults flash logo super hero comics dc comics here is the flash logo for 3d...
cults
free
Spy vs Spy
...spy vs spy cults comics retro spy video_game inspired by spy vs. spy the...
cults
$1
Figurine Venom
...figurine venom cults venom spiderman marvel dc dc comics comics bd figurine keychain key holder figurine of venom,...
cults
$2
FROG FRIEND
...l
frog to support papers, pictures and notes.
it is inspired on a frog´s image. i gave it a comic style to make it more funny.
cults
free
Mjolnir
...hero 3d model of thor's hammer mjolnir from the comicsfilms. hope you like...
Cartoon
cults
$1
cartoon bust HD
...cartoon bust hd
cults
chest cartoon toys figurine
cartoon bust modeled in hd
cults
free
Cartoon Hand Rock
...ts
cartoon hand hands anet a6 duke doks human paint spray sculpture
https://www.youtube.com/watch?v=l81uands0ay
cartoon hands!!!
cults
free
Cartoon Hand Adams
...ts
cartoon hand hands anet a6 duke doks human paint spray sculpture
https://www.youtube.com/watch?v=l81uands0ay
cartoon hands!!!
cults
free
Cartoon Hand Like
...ts
cartoon hand hands anet a6 duke doks human paint spray sculpture
https://www.youtube.com/watch?v=l81uands0ay
cartoon hands!!!
cults
$2
3d cartoons printer nozzle
...nd / cartoon 3d printer nozzle
height of printing 20 cm
for printing it has been cut in 2 to facilitate the removal of media.
cults
$6
voiture cartoon
...voiture cartoon
cults
petite voiture pour enfant
imprimée en 1 bloc, les roues peuvent tourner
cults
free
cartoon phoenix
...anel pattern
stl,obj,jdp,rlf format.phoenix model of bas-relief.
follow me,you will get more free and cheap models.
best regards.
cults
$1
Cat cartoon style
...he "[wooden cat statue](https://skfb.ly/68ngn)" by 3dhdscan licensed under cc attribution. i cleaned the original scan.
cults
$1
Cartoon helicopter
...rsonalize: choose the colors of your filaments, print the parts separately (no need for support) and assemble (no need for glue).
cults
$3
cartoon woman figurine bust
...rintable model (example in photos with 17 cm high)
files in the format obj + tattoo image and logo for printing on blank decal.