GrabCAD
Cake molds
by GrabCAD
Last crawled date: 1 year, 11 months ago
Any rocket is a set of thin-walled shells. The use of bolts
for fastening the shells is not a very good variant:
high contact stresses in the shell, requires the use of reinforcing plates;
overdesigned and weight bolts;
the weakening of the shells, high stress concentration factors, the increase in the error in the calculations of strength...
In many cases it is better to create interface elements by deforming the edges of the shells (as in the figure for the cake molds, nested one inside the other).
This connection can be done in two ways
automatically disconnects when the spacecraft's engine is turned on;
provided with tabs that snap, such a compound becomes a non-separable.
P.S. I understand that this proposal does not fully comply with the conditions. I do not mind that the proposal will not be considered. However, (in my humble opinion) the restrictions must not reduce so greatly the area of choosing the best solutions. In a hyperbolized form: "The rocket body should be made from a single piece of oak and lined with dried snake skins. For fixing snake skins used bronze studs with rod diameter of 0.1 inches and a hemispherical cap diameter of at least 0.5 inch". What is the meaning: Whether engineer must exclaim "What the hell snake skins?!!" or must submissively accept the terms.
for fastening the shells is not a very good variant:
high contact stresses in the shell, requires the use of reinforcing plates;
overdesigned and weight bolts;
the weakening of the shells, high stress concentration factors, the increase in the error in the calculations of strength...
In many cases it is better to create interface elements by deforming the edges of the shells (as in the figure for the cake molds, nested one inside the other).
This connection can be done in two ways
automatically disconnects when the spacecraft's engine is turned on;
provided with tabs that snap, such a compound becomes a non-separable.
P.S. I understand that this proposal does not fully comply with the conditions. I do not mind that the proposal will not be considered. However, (in my humble opinion) the restrictions must not reduce so greatly the area of choosing the best solutions. In a hyperbolized form: "The rocket body should be made from a single piece of oak and lined with dried snake skins. For fixing snake skins used bronze studs with rod diameter of 0.1 inches and a hemispherical cap diameter of at least 0.5 inch". What is the meaning: Whether engineer must exclaim "What the hell snake skins?!!" or must submissively accept the terms.
Similar models
thingiverse
free
Spinning Rocket by Will5204
...'ll still need to buy the rocket engine, though.
size of the rocket engine is 0.74 inches in diameter and 2.745 inches length
3dwarehouse
free
model rocket
...n't know what recovery system to use, since parachutes in all the engine pods may ger tangled. #engine #model_rocket #payload
grabcad
free
2.25" dia. Model Rocket Parts
...be leftover so i made a rocket for my daughter.
uses an estes f15-4 engine.
parachute is a 36" diameter from apogee rockets.
cults
$1
Cake Mold - Cake Mold
...old - cake mold
cults
mold cakes cake cooked
polygon shape cake mold
diameter: 57 mm
height: 20 mm
equipped with handles
thingiverse
free
Maxiwatt silcone sock with thermistor at bottom MOLD by X301N
...the instructions of the original designer.
after the silicone cured and "hardened" open the shell by removing the bolts
thingiverse
free
Quadarachnid Rocket by Will5204
...'ll still need to buy the rocket engine, though.
size of the rocket engine is 0.74 inches in diameter and 2.745 inches length
thingiverse
free
RC rocket missile with drop mechanism by Alextattoo
...ding.
the inner circle of the part called "lock" that hold the rocket must be tight, so sand it just enough to enter!!!
thingiverse
free
4 TIER WEDDING CAKE by cadpro78
... 10, 8 inch wedding cake. made of two 2" cakes per layer. the base could be made of 2" plywood with 18" diameter.
thingiverse
free
cake syringe bolting by berds
... bolting by berds
thingiverse
cake syringe bolting for cake syringes with a diameter of 5cm. the bolting have 3 internal thread.
grabcad
free
5 inch tall round candle design mold
...all round candle design mold
grabcad
this is a free to download candle design mold.
polycarbonate plastic is what i use myself.
Cake
3d_export
$5
Cake
...cake
3dexport
cake
3d_export
free
Cakes
...cakes
3dexport
stylized cakes.
archibase_planet
free
Cake
...cake
archibase planet
pie cake
cake - 3d model for interior 3d visualization.
3ddd
$1
Cakes
...cakes
3ddd
торт
cake collection
3d_export
$5
CAKE
...cake
3dexport
this cake testy very very 228 slava ukraine
archibase_planet
free
Cake
...cake
archibase planet
pastry cookie biscuit
cake - 3d model for interior 3d visualization.
3d_ocean
$4
Small Cake
...small cake
3docean
cake food small
just a small cake ready for render
3d_ocean
$6
Cake Plates
...s
3docean
cake plates
cake plates. folder .mx(2010) contains four different kinds of cake plates with different texture material.
turbosquid
free
Cake
...cake
turbosquid
free 3d model cake for download as fbx on turbosquid: 3d models for games, architecture, videos. (1297951)
turbosquid
$20
Cake
...ke
turbosquid
royalty free 3d model cake for download as max on turbosquid: 3d models for games, architecture, videos. (1588220)
Molds
3ddd
$1
molding
...molding
3ddd
молдинг
molding
3ddd
$1
molding
...molding
3ddd
молдинг , резьба
molding
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
design_connected
$16
Mold
...mold
designconnected
eternit mold computer generated 3d model. designed by charlot, michel.