Thingiverse
Bonsai Mobius Mini + TX02 Mount by darknz
by Thingiverse
Last crawled date: 3 years ago
This is a mount for the Turnigy Bonsai flying wing that mounts a Mobius Mini and Eachine TX02 FPV camera on the front of the wing.
There are two versions to download - the _tv version has simply been rotated to make it look better on Thingiverse, the other version is the original export from Fusion 360.
The center hole allows the Mobius to be mounted with the metal heat-sink/camera mount attached for cooling. It also helps stop the Mobius sliding out backwards, but with velcro this isn't necessary.
When printed in PLA as described below it weights around 8 grams. I've tried to remove as much extra plastic as possible and still have it fairly rigid.
The way I've mounted it means the Mobius can only see a very small amount of the tip of the wing, and the FPV camera can't see the wing at all. When mounted the angle is such that it faces straight ahead when in flight.
Mounting tips
The mount is attached to the Bonsai using 3mm cable ties. The two front cable ties holes are designed to sit above the foward slot in the plywood battery mount. The cable tie runs over the battery strap and back up.
The rear cable ties run through the foam, and the battery strap runs under these to allow the battery to be mounted slightly rearward to fix the center of gravity (see notes below).
The FPV Battery for the TX02 sits behind the COG before the motor. This helps offset the weight of the Mobius and FPV camera.
Center of Gravity
Using this mount and the Mobius will cause the Bonsai to be nose-heavy. I rectified this by moving the battery back by 10mm as shown. Your mileage may vary.
Notes
Pictures show a previous version that is heavier
I'm running 850mah, 3S flight batteries for around 8 min flight time
I'm using 750mah 1s FPV batteries for around 30 min FPV time
The combined weight of the TX02 and battery is around 31 grams, the combined weight of a TS5823 transmitter, aerial and camera (without mount) is around 40 grams, so this is surprisingly a lighter option, plus it doesn't use the flight battery.
range on the TX02 (200mW) is great, I can fly the Bonsai out of sight and still get good reception
I'm using a Mobius Mini B with 135 degree lens.
Cable tie holes have recessed channels for the ties to run through.
There are two versions to download - the _tv version has simply been rotated to make it look better on Thingiverse, the other version is the original export from Fusion 360.
The center hole allows the Mobius to be mounted with the metal heat-sink/camera mount attached for cooling. It also helps stop the Mobius sliding out backwards, but with velcro this isn't necessary.
When printed in PLA as described below it weights around 8 grams. I've tried to remove as much extra plastic as possible and still have it fairly rigid.
The way I've mounted it means the Mobius can only see a very small amount of the tip of the wing, and the FPV camera can't see the wing at all. When mounted the angle is such that it faces straight ahead when in flight.
Mounting tips
The mount is attached to the Bonsai using 3mm cable ties. The two front cable ties holes are designed to sit above the foward slot in the plywood battery mount. The cable tie runs over the battery strap and back up.
The rear cable ties run through the foam, and the battery strap runs under these to allow the battery to be mounted slightly rearward to fix the center of gravity (see notes below).
The FPV Battery for the TX02 sits behind the COG before the motor. This helps offset the weight of the Mobius and FPV camera.
Center of Gravity
Using this mount and the Mobius will cause the Bonsai to be nose-heavy. I rectified this by moving the battery back by 10mm as shown. Your mileage may vary.
Notes
Pictures show a previous version that is heavier
I'm running 850mah, 3S flight batteries for around 8 min flight time
I'm using 750mah 1s FPV batteries for around 30 min FPV time
The combined weight of the TX02 and battery is around 31 grams, the combined weight of a TS5823 transmitter, aerial and camera (without mount) is around 40 grams, so this is surprisingly a lighter option, plus it doesn't use the flight battery.
range on the TX02 (200mW) is great, I can fly the Bonsai out of sight and still get good reception
I'm using a Mobius Mini B with 135 degree lens.
Cable tie holes have recessed channels for the ties to run through.
Similar models
thingiverse
free
Mobius mount for FPV Tricopter by Emaglio by rmooney01
...vibration dampners into the top of the battery cover.
i added slots for a velcro strap to go around the camera as well.
enjoy
thingiverse
free
Mobius Mini Camera Holder by Flugrausch
...cable tie or velcro strap.
the holder itsel can very easily fixed with 2 strips of tape on a flying wing or fuselage for example.
thingiverse
free
Teal Flight Deck by slippytrumpet
...cess holes
includes 3 large diameter holes for wiring runs to power/pcb/flight controller, one front, one rear, one on the side.
thingiverse
free
Turnigy Bonsai Battery Strap Holder by darknz
...ame time because adding it afterwards isn't easy. i've also added extra glue around the sides afterwards just to be sure.
grabcad
free
Eachine FPV Camera Mount
...eeps my camera really nice and steady when i'm driving around. the holes are 2mm big so and bolt you have that size will work
thingiverse
free
Traxxas Revo FPV Mount by Stewpid
...
battery holder was designed around a 370mah 3s battery with dimensions of 31mm x 14mm.
both stl and sldprt files are included.
thingiverse
free
GoPro HERO Session 5 light weight FPV Quad Mount Universal
...approach to an universal gopro session mount. it has around 30 degree tilt and is meant to strap onto aircrafts using cable ties.
thingiverse
free
MRM Reaper/Universal Quadcopter Bottom Battery Mount by 429turbo
...d run the strap across the face of the battery you will use a 250 mm strap. the spacing between the strap rings are 39 mm across.
thingiverse
free
Mobius Remote Camera Mount by menerso
...ip ties to wrap around your rear view mirror bracket and the cable for camera.
it takes a one m3 x 20mm screw and nut and washer.
thingiverse
free
FlexRC Mini Owl - AIO FPV camera mount by FlexRC
...install aio fpv cameras like eachine tx02, tx03 and similarhttps://flexrc.com/product/eachine-tx02-5-8g-40ch-all-in-one-fpv-camera-200mw/ best when printed with nylon or tpu...
Darknz
thingiverse
free
Pinewood Derby Spoiler with Lightening Bolt by darknz
...arknz
thingiverse
modified version of the pinewood derby spoiler by dkrider
now 50mm wide with lightening bolts and flat mounts!
thingiverse
free
Hengstler Counter by darknz
...d with the area where the two parts join. my intent is to use a thin piece of card to separate them rather than print the detail.
thingiverse
free
Headstrap Cable Guides by darknz
...ate them for my own projects.
25x2mm_battery_box_mount is designed to be glued to a battery box so it can be attached to elastic.
thingiverse
free
QX95 Camera Support by darknz
...hold the camera it should be compatible with all aio cameras around this size.
available in 5, 10, 12.5, 15, 17.5, 20, 25 degrees
thingiverse
free
E-11D Stock 2 No Arms Remix by darknz
...l.
the holes for the struts are 20mm deep.
a simple edit in blender that i am sharing in case it is useful to anyone else. enjoy!
thingiverse
free
Ukulele Capo by darknz
...ft self-adhesive velcro to the clamping surfaces works well and will help prevent the ukulele and strings from getting scratched.
thingiverse
free
ZMR 250 Camera Mounts (5 - 25 degrees) by darknz
...e intervals from 5 to 25 degrees.
screw holes are 1.5mm guides to be used as is or drilled out if you require larger size screws.
thingiverse
free
E3D Titan Brackets by darknz
... would overhang. this gets in the way of wheels running on the side of the v-slot. extra height gets all the cogs out of the way.
thingiverse
free
Lipo Battery Tester Case by darknz
...le lcd, and can take up to 5 seconds to tell the voltage of the whole battery and more to tell the voltage of the entire battery.
thingiverse
free
Tarantula MKS Board Cover Shield by darknz
...ormally need the shield on the left (see pics). i'm not yet sure how to control the orientation of the model in the output :)
Tx02
thingiverse
free
TX02 Mounting by axljackass
...tx02 mounting by axljackass
thingiverse
mounting for tx02
thingiverse
free
Eachine TX02 by Cselloman
...eachine tx02 by cselloman
thingiverse
this is a 1:1 copy of the eachine tx02 cam. use it on your designs freely
thingiverse
free
Eachine TX02 by Bankboom
...eachine tx02 by bankboom
thingiverse
camera : eachine tx02 ---> https://goo.gl/hnzgrq
angle : 20 degree
material : tpu
thingiverse
free
Tx01 Tx02 Tx03 support by Ph3nyx
...tx01 tx02 tx03 support by ph3nyx
thingiverse
support for eachine tx01 tx02 tx03 camera
thingiverse
free
TX02 Camera Mount 16x16 by Bankboom
...tx02 camera mount 16x16 by bankboom
thingiverse
i printing with tpu material.
installing hole: 16x16mm
camera : eachine tx02
thingiverse
free
Eachine TX02 FPV camera holder by webdimmy
...eachine tx02 fpv camera holder by webdimmy
thingiverse
eachine tx02 fpv camera holder
thingiverse
free
Eachine TX02 camera mount by WEareFPV
... one with 5° tilt, the second without tilt.
perfect fit for tx02 aio fpv camera
used with eachine qx95 or qx90 or all qx familly.
thingiverse
free
Eachine TX02 top plate for stacks by Impulse819
...e for lightweight builds. this will accommodate a aio eachine tx02 camera and serve as the final top plate for any stacked build.
thingiverse
free
TX02 (eachine) camera mount for QX90 by yoda1490
... the camera+vtx tx02 from eachine to mount on a qx90 micro drone.
just need a little bit of hot glue to maintain it during flight
thingiverse
free
EACHINE TX02 TX01 mount for QX95 by erkark
...eachine tx02 tx01 mount for qx95 by erkark
thingiverse
no support need
Bonsai
3d_export
$7
bonsai
...bonsai
3dexport
bonsai
3ddd
$1
bonsai
...bonsai
3ddd
бонсай
bonsai
turbosquid
$28
Bonsai
...i
turbosquid
royalty free 3d model bonsai for download as max on turbosquid: 3d models for games, architecture, videos. (620228)
turbosquid
$3
Bonsai
...
royalty free 3d model bonsai for download as blend and gltf on turbosquid: 3d models for games, architecture, videos. (1522828)
turbosquid
$29
Bonsai
...oyalty free 3d model bonsai for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1356574)
3ddd
$1
abeliophyllum bonsai
...abeliophyllum bonsai
3ddd
бонсай
abeliophyllum bonsai
абелиолистник бонсай
turbosquid
$50
Bonsai
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
bonsai tree
...bonsai tree
3dexport
-
turbosquid
$13
BONSAI WITH POT
...ree 3d model bonsai with pot for download as ma, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1576011)
3d_export
$7
bonsai
...decorating houses in asian style<br>a real one costs a lot, so why not buy a virtual one from me for a couple of dollars?;)
Mobius
design_connected
$11
Mobius
...mobius
designconnected
kristalia mobius coffee tables computer generated 3d model. designed by lucidi pevere.
turbosquid
free
Mobius
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$120
Mobius bracelet
...mobius bracelet
3dexport
mobius bracelet 3d render modelling animation
3ddd
$1
Mobius Table
...mobius table
3ddd
kristalia , кофейный
mobius coffee table by kristalia
design_connected
$25
Mobius C
...mobius c
designconnected
zenith mobius c computer generated 3d model. designed by schamburg, marc.
3d_export
$5
mobius bracelet
...mobius bracelet
3dexport
3d model of a mobius bracelet.<br>modeled in solidworks.<br>rendered in keyshot.
turbosquid
$19
red mobius
...bosquid
royalty free 3d model red mobius for download as max on turbosquid: 3d models for games, architecture, videos. (1353147)
turbosquid
free
Mobius Desk
...y free 3d model mobius desk for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1229898)
turbosquid
$2
Mobius ring
...e 3d model mobius ring for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1195725)
turbosquid
free
Mobius strip
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Mini
turbosquid
$10
Mini Mini Luceplan
...
royalty free 3d model mini mini luceplan for download as max on turbosquid: 3d models for games, architecture, videos. (1227359)
3d_ocean
$39
Mini Cooper
...mini cooper
3docean
cabrioler cooper mini
mini cooper cabrioler
3d_export
$30
Mini lathe
...mini lathe
3dexport
mini lathe
3d_export
$5
mini mouse
...mini mouse
3dexport
mini mouse
3d_export
$5
mini house
...mini house
3dexport
mini house
3d_export
free
Mini Mecha
...mini mecha
3dexport
concept of mini mecha
3d_ocean
$20
Mini Gun
...mini gun
3docean
gatling gun gun machine gun mini gun weapon
model of a mini gatling gun.
3ddd
free
Herve mini
... кофейный , herve
http://www.mobiliavenanti.it/ru/products/hervè-mini
3d_export
$5
mini wall
...mini wall
3dexport
mini wall for living room
3d_export
$5
mini bank
...mini bank
3dexport
mini bank 3d model
Mount
3d_export
free
mounting bracket
...mounting plate is the portion of a hinge that attaches to the wood. mounting plates can be used indoors, cabinetry and furniture.
turbosquid
$2
MOUNTING
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mounts
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mount Fuji
...fuji
turbosquid
free 3d model mount fuji for download as obj on turbosquid: 3d models for games, architecture, videos. (1579977)
3d_export
$5
Headphone mount LR
...headphone mount lr
3dexport
headphone mount l+r
turbosquid
$39
Mount rainier
...quid
royalty free 3d model mount rainier for download as fbx on turbosquid: 3d models for games, architecture, videos. (1492586)
turbosquid
$5
pipe mounting
...quid
royalty free 3d model pipe mounting for download as obj on turbosquid: 3d models for games, architecture, videos. (1293744)
turbosquid
$3
Mounting Tires
...uid
royalty free 3d model mounting tires for download as fbx on turbosquid: 3d models for games, architecture, videos. (1708511)
3d_export
$5
Magnetic GoPro Mount
...pro mount
3dexport
cool magnetic mount for gopro. allows you to mount the camera on flat metal surfaces and get exclusive shots.
turbosquid
$5
Stone Mount
...ty free 3d model stone mount for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1370306)