Thingiverse
Bike Thru-Axle Clamp Mount by FlyByTom
by Thingiverse
Last crawled date: 2 years, 10 months ago
Needed a way to mount bikes with thru-axles in the back of my van. Decided on this clamping design as its easier to load and unload bikes rather than solid thru axle mounts that I used in the past.
This was designed to work with 12x100mm, 12x110mm, 15x100mm, and 15x110mm thru axles. There are two different sleeves for either 12mm or 15mm that snap into place. I printed my sleeves out of 98A TPU but also tested and works in PETG, PLA, or 95A TPU. The sleeves are interchangeable so one mount can be used for different bikes by switching sleeves.
The bases come in two different flavors, either narrow or wide. The base is modular so either mount can be fitted to the top half or the top half can be mounted directly via the 4x 1/4"-20 holes. The base hole spacing on both mounts is designed around aluminum L-Track with 3/8" studs. I also provided a version with 1/4" holes for different mounting options if you are not using L-Track.
After testing a few locking cams I settled on one with a 2mm lever offset so that it locks in place. After spending hours driving around it has stayed tight and hasn't come loose.
I printed my cam.locks out of PETG and 98A TPU and prefer the TPU but both work. I provided 3 versions of the locks so you can tune how tight you want the lock to feel. I recommend trying the one with no offset first.
I printed all parts with 11 perimeter walls to make sure it was very tough. Not sure if that is completely necessary but I'd rather have it too tough than fall apart. I tried hard to break this mount and went through multiple design improvements to make it as tough as reasonable possible. I printed all parts in PETG except for the sleeve and cam.lock which were printed in 98A TPU. Entire mount with Narrow Base uses approximately 240g of filament.
Hardware Needed;
1x - 1/4"-20 x 3 3/8" countersunk machine screw - for main hinge
4x - 1/4"-20 x 1.25" countersunk or round machine screw - for base
2x - #10-24 x 3" round machine screw - for cam locks
1x - #10-24 x 2" countersunk machine screw - for cam lever
Parts to Print (refer to photos for recommended orientation and supports)
1) BikeClampMount.Bottom
2) BikeClampMount.Top
3) Cam.Lever
4) Cam.Lock.L
5) Cam.Lock.R
6) Sleeve
7) Base
This was designed to work with 12x100mm, 12x110mm, 15x100mm, and 15x110mm thru axles. There are two different sleeves for either 12mm or 15mm that snap into place. I printed my sleeves out of 98A TPU but also tested and works in PETG, PLA, or 95A TPU. The sleeves are interchangeable so one mount can be used for different bikes by switching sleeves.
The bases come in two different flavors, either narrow or wide. The base is modular so either mount can be fitted to the top half or the top half can be mounted directly via the 4x 1/4"-20 holes. The base hole spacing on both mounts is designed around aluminum L-Track with 3/8" studs. I also provided a version with 1/4" holes for different mounting options if you are not using L-Track.
After testing a few locking cams I settled on one with a 2mm lever offset so that it locks in place. After spending hours driving around it has stayed tight and hasn't come loose.
I printed my cam.locks out of PETG and 98A TPU and prefer the TPU but both work. I provided 3 versions of the locks so you can tune how tight you want the lock to feel. I recommend trying the one with no offset first.
I printed all parts with 11 perimeter walls to make sure it was very tough. Not sure if that is completely necessary but I'd rather have it too tough than fall apart. I tried hard to break this mount and went through multiple design improvements to make it as tough as reasonable possible. I printed all parts in PETG except for the sleeve and cam.lock which were printed in 98A TPU. Entire mount with Narrow Base uses approximately 240g of filament.
Hardware Needed;
1x - 1/4"-20 x 3 3/8" countersunk machine screw - for main hinge
4x - 1/4"-20 x 1.25" countersunk or round machine screw - for base
2x - #10-24 x 3" round machine screw - for cam locks
1x - #10-24 x 2" countersunk machine screw - for cam lever
Parts to Print (refer to photos for recommended orientation and supports)
1) BikeClampMount.Bottom
2) BikeClampMount.Top
3) Cam.Lever
4) Cam.Lock.L
5) Cam.Lock.R
6) Sleeve
7) Base
Similar models
thingiverse
free
Fork Mount for Bike - 15mm thru-axle + adapters by Reed12321
...ggest using a drill to clean out the support pieces. i printed with supports at 8% thickness and that seemed to work really well.
thingiverse
free
Micro Apex 3" parts by M490fpv
... m8.2 gps)
motor wire protector/soft mount
i printed these of extrudr tpu 98a filament, colors used, were powder beige and black.
thingiverse
free
Right-handed Fanatec Clubsport Shifter Mount for Playseat Challenge by CarbonBasedLifeform
...-20 bolts/machine screws
4x - m6x~18mm bolts/machine screws
you'l need 1x of the large parts, and 3x of the rectangular pins.
thingiverse
free
Hobie H Rail Leash Mount
...ed petg 30% infill, .06mm nozzle, 4 perimeters
bom:
4x #10-24 x 1.25" lg stainless screws
4x #10-24 stainless nylon lock nut
thingiverse
free
SMO 4K mount for Geprc Rocket & Crocodile Baby by EatMorePossum
...eprc crocodile baby (the latter will only use two of the screw holes).
the diameter of the screw is 1.89 mm and length is 15 mm.
thingiverse
free
Euro Truck R/C Trailer by FeedbackSoundCompany
...e save a lot of weight. print solid for strength and use every hold in the axle mount as these are going to break occasionally...
thingiverse
free
12mm and 15mm bicycle thru axle holder for pegboard
...a place to put the thru-axle when i'm removing the front wheel during bike maintenance.
fusion 360 files available on request
thingiverse
free
CAM Lock for CNC machine by sockles
...nc machine by sockles
thingiverse
needed a way to hold my parts from the side on my cnc machine.
holds a 1/4" panhead screw
thingiverse
free
Mini tree Star Topper Mount by tygunn
...n
thingiverse
clamp mount for 3/4" conduit to mount a mini tree star. holes are printed for a 1/4" machine screw tap.
thingiverse
free
PolyBot Effector Base by WilliamAAdams
... there's a lot of surface area, and it will tend to want to warp. so, print with a high raft to absorb some of that warpage.
Flybytom
thingiverse
free
Mercedes Sprinter Doorstop by FlyByTom
...pu so it wouldn't crack over time.
design has been in use for 6+ months on two different vans and is holding up well.
enjoy!
thingiverse
free
Arlo Doorbell Wedge for Siding by FlyByTom
...at also pivot on the vertical plain by 5 and 15 degrees respectively.
printed in petg for durability and temperature resistance.
thingiverse
free
Winnebago Revel Euroloft Wrench Storage by FlyByTom
... tape.
design has been in use for 6 months with no issues. enjoy!
printed mine in petg for temperature resistance and longevity.
thingiverse
free
Spray Paint Rack by FlyByTom
...tubes without them slipping threw the gap.
printed in petg for durability and temp resistance since mine is mounted in a garage.
thingiverse
free
Sortimo 2x3 Label Collar by FlyByTom
...g:4752763
1x1 3d printed binshttps://www.thingiverse.com/thing:4752746
1x2 cap and labelhttps://www.thingiverse.com/thing:4774741
thingiverse
free
Sortimo 2x2 Label Collar by FlyByTom
...g:4752763
1x1 3d printed binshttps://www.thingiverse.com/thing:4752746
1x2 cap and labelhttps://www.thingiverse.com/thing:4774741
thingiverse
free
Sortimo 1x2 Label Collar by FlyByTom
...g:4752763
1x1 3d printed binshttps://www.thingiverse.com/thing:4752746
1x2 cap and labelhttps://www.thingiverse.com/thing:4774741
thingiverse
free
Sortimo 1x1 Bin - Label Collar by FlyByTom
...g:4752763
1x1 3d printed binshttps://www.thingiverse.com/thing:4752746
1x2 cap and labelhttps://www.thingiverse.com/thing:4774741
thingiverse
free
Sortimo 1x2 Bin Cap and Label by FlyByTom
...g:4752763
1x1 3d printed binshttps://www.thingiverse.com/thing:4752746
1x2 cap and labelhttps://www.thingiverse.com/thing:4774741
thingiverse
free
Bosch/Sortimo i-Boxx 1x1 Bin Divider by FlyByTom
...thing:4803822
2x2 label collarhttps://www.thingiverse.com/thing:4803795
2x3 label collarhttps://www.thingiverse.com/thing:4803815
Thru
thingiverse
free
15mm Thru Axle to 9mm Thru Bolt Adapter 100mm by foo_fighter
...ter
thingiverse
this will allow you to use a 100mm front 15mm thru axle hub with a 9mm thru bolt(like a dt swiss rws thru bolt.)
thingiverse
free
McDonalds Drive Thru by Smirnoff21ice
...mcdonalds drive thru by smirnoff21ice
thingiverse
mcdonalds drive thru
thingiverse
free
Thru-hull cable for Kayaks by akhenatn
...thru-hull cable for kayaks by akhenatn
thingiverse
thru-hull cable for kayaks, commonly used for electronics, pump installation
thingiverse
free
Bicycle dummyhub for 12x142mm thru axle by tecnopro
...bicycle dummyhub for 12x142mm thru axle by tecnopro
thingiverse
dummyhub for 12x142mm thru axle.
thingiverse
free
Cable Labels 7 thru 16 by Hermy21
...cable labels 7 thru 16 by hermy21
thingiverse
cable labels for #7 thru #16
thingiverse
free
slicer block thru by maxadam
...slicer block thru by maxadam
thingiverse
slicer block with slices all the way through.
thingiverse
free
Arch Base Pass Thru V5
...ss thru
designed for double arches
1/2 inch pvc for the arch
1/2 inch metal emt for the cross brace that holds the ends together.
thingiverse
free
Thru Axle End caps by foo_fighter
... or when traveling to protect the hubs and the travel bags/cases.
the 20mm_thru_axle_cap.scad has the axle diameter programmable.
thingiverse
free
Chain keeper thru axle (Long) by PostMelvin
...ain keeper for bikes with a 12x100mm thru-axle (long version). remove the wheel and insert the tool for maintenance on your bike.
thingiverse
free
Chain keeper thru-axle (Short) by PostMelvin
... chain keeper for bikes with a 12mm thru-axle (short version). remove the wheel and insert the tool for maintenance on your bike.
Axle
thingiverse
free
Axle
...axle
thingiverse
axle
thingiverse
free
Axle Hub
...axle hub
thingiverse
axle hub
thingiverse
free
Hex axle lift axle by scaletruckpartdesigner
...he housing. axle housing is 120mm. this will fit a dual wheel or single wheel with hex hub. this will fit all factory suspension.
thingiverse
free
Axle
...axle
thingiverse
watch frozen ii online
thingiverse
free
Axle
...axle
thingiverse
watch frozen ii online
thingiverse
free
Axle
...axle
thingiverse
watch ip man 4: the finale online
thingiverse
free
axle clamp for Ossum Jeep with mrcrankyface axles by jjpython
... clamp for ossum jeep with mrcrankyface axles by jjpython
thingiverse
this is to hold the mrcrankyface axles onto the ossum jeep
thingiverse
free
robocar axle by umitakin
...robocar axle by umitakin
thingiverse
robocar axle
thingiverse
free
4502595 (Technic, Axle Connector Hub with 3 Axles) by melmaking
...technic, axle connector hub with 3 axles) by melmaking
thingiverse
this is a technic, axle connector hub with 3 axles
have fun !
thingiverse
free
back axle by Gogo327
...back axle by gogo327
thingiverse
attempt at a back axle
Bike
thingiverse
free
Bike
...bike
thingiverse
bike keychain
thingiverse
free
Bike by naaron
...bike by naaron
thingiverse
bike
thingiverse
free
BIKE by nagato
...bike by nagato
thingiverse
bike
thingiverse
free
a bike by KySyth
...a bike by kysyth
thingiverse
a bike
thingiverse
free
Mirror Bike
...mirror bike
thingiverse
bike mirror
thingiverse
free
Bike Light
...bike light
thingiverse
bike light
thingiverse
free
Bike Hanger (Racing Bike) by MakerPoint
...hanger (racing bike) by makerpoint
thingiverse
easy, material friendly, bike hang system!
print it on its side! so it stronger
thingiverse
free
Bike by tleijssen
...bike by tleijssen
thingiverse
a easy model of a bike.
there are assembly instructions in teh files.
thingiverse
free
Bike & Female
...bike & female
thingiverse
bike & female low poligon ver.
thingiverse
free
Bike hanger by Jovior
... by jovior
thingiverse
bike hanger,
u can use road bike, mountain bike or road bike with profile under 60 mm.
printed in pla :)
Clamp
thingiverse
free
Clamp
...clamp
thingiverse
clamp
thingiverse
free
Clamp
...clamp
thingiverse
clamp for vacform
thingiverse
free
Clamp by bexer
...clamp by bexer
thingiverse
clamp, one clamp for many possibilities!
thingiverse
free
clamp by kimduckkyo
...clamp by kimduckkyo
thingiverse
clamp
thingiverse
free
clamp by glukofinder
...clamp by glukofinder
thingiverse
clamp
thingiverse
free
Clamp Chain
...clamp chain
thingiverse
this is a clamp
thingiverse
free
Clamp by wslab
...clamp by wslab
thingiverse
clamp
thingiverse
free
CLAMP by leonk
...clamp by leonk
thingiverse
clamp
thingiverse
free
Clamp by jkorinek87
...clamp by jkorinek87
thingiverse
clamp
thingiverse
free
Clamp by Emmanuelgnanasekar
...clamp by emmanuelgnanasekar
thingiverse
this thing is a clamp model , it can be used for soft clamping things
Mount
thingiverse
free
Pen Mount on BLTouch mount by jetspot
...pen mount on bltouch mount by jetspot
thingiverse
pen mount on bltouch mount
thingiverse
free
RAM Mount, Mount by seanmclean
...ram mount, mount by seanmclean
thingiverse
bridging plate to attach ram mount to yamaha 242, for chartplotter placement.
thingiverse
free
Mount for mount for Garmin GPS by GNOBLIN
...you can use this mount for prevent rotation simple mount around hendelbars.
d handelbar 31.8mm
use m3 screw and din 16903 plug.
thingiverse
free
Permanent mount for Modular Mounting System by WIR14
...permanent mount for modular mounting system by wir14
thingiverse
permanent mount for modular mounting system.
thingiverse
free
Gopro Mount and antenna mount by SuperYoyo
...gopro mount and antenna mount by superyoyo
thingiverse
cut the carbon platform to pass the gopro mount and enjoy !
thingiverse
free
Hexagon Mount for 50mm Mount (Sparkcube) by Draman
...for 50mm mount (sparkcube) by draman
thingiverse
hexagon mount remix from skimmys hotend-mount for sparkcube or other 50mm-mount
thingiverse
free
mount by gixster
...mount by gixster
thingiverse
custom mount
thingiverse
free
Mount by Matrxi999
...mount by matrxi999
thingiverse
shelf mount
thingiverse
free
Motor mount
...motor mount
thingiverse
motor mount
thingiverse
free
GoPro Mount
...gopro mount
thingiverse
gopro mount