Thingiverse
Bienenwaben LED-Stripe Lampensystem (Honeycomb Light) by jobeagle
by Thingiverse
Last crawled date: 3 years ago
Das Bienenwabenlampensystem besteht aus mehreren druckbaren Komponenten:
Wabensegment zum bestücken mit 10 mm breiten LED-Band und aufschnappen auf Grundhalter (Beispiellampe: 9)
Grundhalter Segment 1 mit einem Führungsquader (Beispiellampe: 4)
Grundhalter Segment 2 mit zwei Führungsquadern (Beispiellampe: 3)
Abdeckkappe 1 Zungen (Beispiellampe: 9)
Abdeckkappe 2 Quader (Beispiellampe: 10*)
Der Grundhalter wird mittels Führungsnuten und entsprechenden Nasen zusammengesteckt und mit Kleber (ich verwende in Aceton aufgelöstes ABS) fixiert.
Die Grundform kann (fast) beliebig variieren. Die Grundhalter können entweder an der langen oder an der schmalen Seite zusammengeklickt werden. Hier im Beispiel hat sie die Form eines Kreuzes.
Grundhalter Segment 1 und Segment 2 wechseln sich immer ab.
Anschließend werden die benötigten Wabensegmente (im Beispiel 9 Stück) mit dem LED-Lichtband bestückt. Das Band wird nur zwischen die beiden Führungsschienen gedrückt und nicht verklebt. Dabei können die LEDs nach außen oder nach innen gerichtet werden (siehe Bild). Im Beispiel sind die beiden innersten nach innen gerichtet und alle anderen nach außen. Die Lichtausbeute ist bei nach außen gerichteten LEDs höher! Das LED-Band wird mittels Schere an den „erlaubten“ Stellen entsprechend gekürzt und z.B. mit einer Zwillingslitze verbunden. Als Querschnitt sollten mind. 0,2 mm2, bei größeren Lampen mehr verwendet werden. Im Beispiel wurde ein Flachbandkabel mit 4 Litzen (zusammengeschlossen: je zwei für Plus und Minus 12V) verwendet.
Als LED-Band wird im Beispiel folgender Typ benutzt: V-TAC "SMD 5730" mit 20-22 Lumen pro Chip, damit ergibt sich pro 4er-Segment ca. 900 Lumen und die Lampe hat insgesamt ca. 8000 lm. Davon muss natürlich abgezogen werden, was durch die schlechte Transparenz des ABS verloren geht und ebenso nach innen gerichtete LED-Elemente. Die Lampe ist trotzdem sehr hell und kann z.B. locker eine einzelne 58 Watt Leuchtstoffröhre ersetzen. Die Lichtfarbe des verwendeten LED-Bandes ist sehr warm und ähnelt früheren Glühlampen.
Die Halter wurden mittels weißem ABS und die Wabensegmente mit „naturfarbenem“ ABS gedruckt.
Beim zusammenklicken ist zu beachten, daß die Schnappzungen richtig einschnappen - evtl. ist das Wabensegment um 90 Grad zu drehen!
Die Abdeckkappen werden farbig nach Wahl gedruckt (hier grün) und müssen, bei Schwergängigkeit etwas nachgearbeitet oder, falls sie nicht halten, mittels Kleber (Klebestift) befestigt werden.
Als Steuergerät wird z.B. folgender Typ verwendet: LPV-60-12
Bei größeren Lampen muss die Stromversorgung von beiden Seiten des LED-Leuchtbandes erfolgen!
Ich habe das Steuergerät auf einem Regal in der Nähe der Lampe befestigt und nur die 12V Versorgung zu der Lampe installiert (hier Zwillingslitze mit 2*0,75 mm2).
----------------------------------------- english -----------------------------------------------------------------
The honeycomb lamp system consists of several printable components:
Honeycomb segment to equip with 10 mm wide LED strip and snap onto base holder (example lamp: 9)
Basic holder segment 1 with a guide block (example lamp: 4)
Basic holder segment 2 with two guide blocks (example lamp: 3)
Cover 1 tabs (example lamp: 9)
Cover 2 cuboid (example lamp: 10*)
The basic holder is put together by means of guide grooves and corresponding noses and fixed with adhesive (I use ABS dissolved in acetone).
The basic form can vary (almost) arbitrarily. The basic holders can be clicked together either on the long side or on the short side. Here in the example it has the shape of a cross.
Basic holder segment 1 and segment 2 always alternate.
Then the required honeycomb segments (in the example 9 pieces) are equipped with the LED light band. The tape is only pressed between the two guide rails and not glued. The LEDs can be directed outwards or inwards (see picture). In the example, the two innermost ones are directed inwards and all others are directed outwards. The light output is higher with LEDs facing outwards! The LED tape is shortened accordingly by means of scissors at the "allowed" positions and e.g. connected to a twin strand. As a cross-section, at least 0.2 mm2 should be used, for larger lamps more. In the example, a ribbon cable with 4 strands (together: two each for plus and minus 12V) was used.
As an LED strip, the following type is used in the example: V-TAC "SMD 5730" with 20-22 lumens per chip, resulting in per 4-segment about 900 lumens and the lamp has a total of about 8000 lm. Of course, this must be deducted, which is lost due to the poor transparency of the ABS and also inward-looking LED elements. The lamp is still very bright and can e.g. Loosely replace a single 58 watt fluorescent tube. The light color of the LED strip used is very warm and resembles earlier incandescent bulbs.
The holders were printed using white ABS and the honeycomb segments with "natural" ABS.
When clicking together, make sure that the snap tabs snaps in correctly - possibly the honeycomb segment must be turned 90 degrees!
The cover caps are printed in color of your choice (here green) and have to be slightly reworked if they are stiff or, if they do not hold, they have to be fixed with glue (glue stick).
As a power supply, e.g. the following type is used: LPV-60-12
For larger lamps, the power must be connected from both sides of the LED strip!
I have mounted the controller on a shelf near the lamp and installed only the 12V supply to the lamp (here twin wire with 2 * 0.75 mm2).
Wabensegment zum bestücken mit 10 mm breiten LED-Band und aufschnappen auf Grundhalter (Beispiellampe: 9)
Grundhalter Segment 1 mit einem Führungsquader (Beispiellampe: 4)
Grundhalter Segment 2 mit zwei Führungsquadern (Beispiellampe: 3)
Abdeckkappe 1 Zungen (Beispiellampe: 9)
Abdeckkappe 2 Quader (Beispiellampe: 10*)
Der Grundhalter wird mittels Führungsnuten und entsprechenden Nasen zusammengesteckt und mit Kleber (ich verwende in Aceton aufgelöstes ABS) fixiert.
Die Grundform kann (fast) beliebig variieren. Die Grundhalter können entweder an der langen oder an der schmalen Seite zusammengeklickt werden. Hier im Beispiel hat sie die Form eines Kreuzes.
Grundhalter Segment 1 und Segment 2 wechseln sich immer ab.
Anschließend werden die benötigten Wabensegmente (im Beispiel 9 Stück) mit dem LED-Lichtband bestückt. Das Band wird nur zwischen die beiden Führungsschienen gedrückt und nicht verklebt. Dabei können die LEDs nach außen oder nach innen gerichtet werden (siehe Bild). Im Beispiel sind die beiden innersten nach innen gerichtet und alle anderen nach außen. Die Lichtausbeute ist bei nach außen gerichteten LEDs höher! Das LED-Band wird mittels Schere an den „erlaubten“ Stellen entsprechend gekürzt und z.B. mit einer Zwillingslitze verbunden. Als Querschnitt sollten mind. 0,2 mm2, bei größeren Lampen mehr verwendet werden. Im Beispiel wurde ein Flachbandkabel mit 4 Litzen (zusammengeschlossen: je zwei für Plus und Minus 12V) verwendet.
Als LED-Band wird im Beispiel folgender Typ benutzt: V-TAC "SMD 5730" mit 20-22 Lumen pro Chip, damit ergibt sich pro 4er-Segment ca. 900 Lumen und die Lampe hat insgesamt ca. 8000 lm. Davon muss natürlich abgezogen werden, was durch die schlechte Transparenz des ABS verloren geht und ebenso nach innen gerichtete LED-Elemente. Die Lampe ist trotzdem sehr hell und kann z.B. locker eine einzelne 58 Watt Leuchtstoffröhre ersetzen. Die Lichtfarbe des verwendeten LED-Bandes ist sehr warm und ähnelt früheren Glühlampen.
Die Halter wurden mittels weißem ABS und die Wabensegmente mit „naturfarbenem“ ABS gedruckt.
Beim zusammenklicken ist zu beachten, daß die Schnappzungen richtig einschnappen - evtl. ist das Wabensegment um 90 Grad zu drehen!
Die Abdeckkappen werden farbig nach Wahl gedruckt (hier grün) und müssen, bei Schwergängigkeit etwas nachgearbeitet oder, falls sie nicht halten, mittels Kleber (Klebestift) befestigt werden.
Als Steuergerät wird z.B. folgender Typ verwendet: LPV-60-12
Bei größeren Lampen muss die Stromversorgung von beiden Seiten des LED-Leuchtbandes erfolgen!
Ich habe das Steuergerät auf einem Regal in der Nähe der Lampe befestigt und nur die 12V Versorgung zu der Lampe installiert (hier Zwillingslitze mit 2*0,75 mm2).
----------------------------------------- english -----------------------------------------------------------------
The honeycomb lamp system consists of several printable components:
Honeycomb segment to equip with 10 mm wide LED strip and snap onto base holder (example lamp: 9)
Basic holder segment 1 with a guide block (example lamp: 4)
Basic holder segment 2 with two guide blocks (example lamp: 3)
Cover 1 tabs (example lamp: 9)
Cover 2 cuboid (example lamp: 10*)
The basic holder is put together by means of guide grooves and corresponding noses and fixed with adhesive (I use ABS dissolved in acetone).
The basic form can vary (almost) arbitrarily. The basic holders can be clicked together either on the long side or on the short side. Here in the example it has the shape of a cross.
Basic holder segment 1 and segment 2 always alternate.
Then the required honeycomb segments (in the example 9 pieces) are equipped with the LED light band. The tape is only pressed between the two guide rails and not glued. The LEDs can be directed outwards or inwards (see picture). In the example, the two innermost ones are directed inwards and all others are directed outwards. The light output is higher with LEDs facing outwards! The LED tape is shortened accordingly by means of scissors at the "allowed" positions and e.g. connected to a twin strand. As a cross-section, at least 0.2 mm2 should be used, for larger lamps more. In the example, a ribbon cable with 4 strands (together: two each for plus and minus 12V) was used.
As an LED strip, the following type is used in the example: V-TAC "SMD 5730" with 20-22 lumens per chip, resulting in per 4-segment about 900 lumens and the lamp has a total of about 8000 lm. Of course, this must be deducted, which is lost due to the poor transparency of the ABS and also inward-looking LED elements. The lamp is still very bright and can e.g. Loosely replace a single 58 watt fluorescent tube. The light color of the LED strip used is very warm and resembles earlier incandescent bulbs.
The holders were printed using white ABS and the honeycomb segments with "natural" ABS.
When clicking together, make sure that the snap tabs snaps in correctly - possibly the honeycomb segment must be turned 90 degrees!
The cover caps are printed in color of your choice (here green) and have to be slightly reworked if they are stiff or, if they do not hold, they have to be fixed with glue (glue stick).
As a power supply, e.g. the following type is used: LPV-60-12
For larger lamps, the power must be connected from both sides of the LED strip!
I have mounted the controller on a shelf near the lamp and installed only the 12V supply to the lamp (here twin wire with 2 * 0.75 mm2).
Similar models
3dwarehouse
free
Zeitnehmer Holz
...m die 5 leds in der mitte. ist die zeit abgelaufen, gehen die leds im kreis aus und die 5 leds in der mitte leuchten. #spiel_zeit
thingiverse
free
Plantronics Gamecom 780 Headband by Inkaepseleur
...ießend mit einem multec multirap m420 (single-extruder) bei verwendung von rotem pla-ht filament (hersteller simona) ausgedruckt.
thingiverse
free
Spool Holder / Filament Halterung by ProjektC
...terschiedliche höhe haben.
nach das rauf und runter sehr leicht geht, wird je nach spooler füllung von oben nach unten gewandert.
3dwarehouse
free
Wissensturm Linz
...nger #oberösterreich #stadtbibliothek_linz #stögmüller #tower_of_knowledge #upper_austria #vhs #volkshochschule #wissensturm_linz
thingiverse
free
Volksfräse - LED Halterung by BeNeDeLuX
...bei dem design verliest du keinen bauraum der fräse und die led's beleuchten mit den 120° abstrahlwinkel die fläche sehr gut.
thingiverse
free
Tools 4 Resinbottles by CENTVRIO
...le resin" konzipiert und angepasst.
das bild zeigt beide tools in ihrere druckstellung,
verstärkungen werden nicht benötigt.
thingiverse
free
Oberwagenlaterne by stephanbrunker
... brücke über der öffnung halbwegs sauber gedruckt wird. die druckteile wurden danach abgeschliffen und mit acteon dampfbehandelt.
thingiverse
free
Blinker Dynamisch by Gsedv
...tinen.
wer jedoch eine fertige platine haben möchte ,kann mir gerne eine nachricht schreiben.
und nun viel spass beim nachbauen!!
3dwarehouse
free
Altes Rathaus Plauen
...2 fenstern texturiert und müssen noch überarbeitet werden. der seitenflügel und die rolandstatue von heinrich dem iv. fehlt noch.
thingiverse
free
Düsenbox für VulcanoDüsen by donremi
... magnetisch. die magnete(6x d2x2) werden eigepresst
die achse ist ein stück filament (d1.75), dass mit einem lötstab fixiert wird
Bienenwaben
thingiverse
free
Connector (Steam) Wax Melter - Beewax by dmar29
...wagner w16 direkt an eine box zum ausschmelzen der bienenwaben verbinden. im internet gibt es viele diy-projekte zum thema...
grabcad
free
Beehive - Bienenwaben Catia v5 / Siemens NX 11 / Inventor 2017 / Autocad 2017 & Tutorial
...dovvym
link to the solidworks 2016 video: https://youtu.be/unp2wez8xqw
link to the fusion 360 video: https://youtu.be/lhts_wae2xw
Jobeagle
thingiverse
free
Krups Typ 355 Messerverschluss by jobeagle
...
ersatzteil für krups allesschneider typ 355. das gewinde des messerverschlusses war defekt, deshalb wurde ein neuer konstruiert.
thingiverse
free
door case hanger support by jobeagle
...the door case.
our door case has a thickness of 50.2 mm. you can scale it for your practice.
printed with pla on a ctc dual head.
thingiverse
free
LED Stripe Mounting Clip by jobeagle
...e 2.5mm * 8mm schrauben. 3mm sind auch noch ok.
mounting clip for 10mm led-stripe. i use 2.5mm * 8mm screws, 3 mm screw fits too.
thingiverse
free
MTB Bremskolbentool (MTB Brake Tool) by jobeagle
... simply push the tool from the outside until it stops, pull it out and the pistons are back! it works with 2 and 4 piston brakes.
thingiverse
free
Ender 3 Pro Light with LED Strip by jobeagle
... als die verwendeten 6 segmente des streifens ausreichen. es wird ferner ein gleichstrom-netzteil mit 12v und ca. 300ma benötigt.
Honeycomb
3d_export
$5
honeycomb
... a model of a honeycomb by using blender. preview images were rendered with blender eevee. enjoy the product and leave a comment.
3ddd
$1
Honeycomb Floor
... паркет
parquet with metalic honeycomb floor
demensions 500x500 cm xy
multitexture + floorgenerator
turbosquid
$3
honeycomb lampshade
...free 3d model honeycomb lampshade for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1221234)
turbosquid
$12
Honeycomb chest
...ee 3d model honeycomb chest for download as 3ds, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1455008)
turbosquid
$13
Shelf - honeycombs
...del shelf - honeycombs for download as mat, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1193801)
turbosquid
$6
HONEYCOMB FILLING_DOOR
...oneycomb filling_door for download as ma, max, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1274244)
3d_export
$5
honeycomb vase
...3d model of honeycomb vase designed using solid works. it can easily converted to desire format for 3d printing or cnc machining.
turbosquid
$14
Maps Honeycomb
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
Honeycomb Cabinet
...honeycomb cabinet for download as max, 3ds, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1632735)
3d_export
$8
honeycomb patterned toroid ring
...honeycomb patterned toroid ring
3dexport
complex honeycomb pattern on toroid ring
Stripe
3ddd
$1
Stripe
...im king , stripe
стул из прутьев "stripe" - дизайн
джоачим кинг (joachim king)
3ddd
free
Skandiform Stripe
...skandiform stripe
3ddd
skandiform , stripe
skandiform stripe
3ddd
$1
Magis Striped
...otti/striped/striped/
моделились по чертежам
стеки не схлопнуты
итерацию можно настроить по вкусу
текстура в комплекте
3ddd
free
Stripe courtains
...ecoration , curtain , fabrics
stripe courtains.
3ddd
$1
Stripe F262
... stripe
http://www.skandiform.se/produkter/faatoeljer-soffor/stripe-f-262/?lang=en
design_connected
$16
Stripe Rug
...stripe rug
designconnected
stripe rug computer generated 3d model.
3ddd
free
striped fabric
...striped fabric
3ddd
difuse + bump
turbosquid
$12
Striped bed
...y free 3d model striped bed for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1351926)
turbosquid
$9
Striped Vase
... free 3d model striped vase for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1448298)
turbosquid
$19
Striped Blouse
...d model striped blouse for download as 3ds, obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1430922)
Led
3d_export
$5
led
...led
3dexport
the led is cut with all the parts.
3ddd
$1
Monacor / PARL56DMX / LED-320RGBW / LED-345RGBW / LED-300RGB
... прожектор
http://www.monacor.dk/
parl56dmx
led-320rgbw
led-345rgbw
led-300rgb
turbosquid
$10
LED
...led
turbosquid
free 3d model led for download as blend on turbosquid: 3d models for games, architecture, videos. (1691856)
3d_export
$5
led lamp
...led lamp
3dexport
led lamp, brightness animation
3ddd
free
leds-c4
...leds-c4
3ddd
leds-c4
современный торшер
3ddd
free
leds-c4
...leds-c4
3ddd
leds-c4
настольный лампа
turbosquid
$19
LED
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
Led
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
LED
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
LED
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Light
archibase_planet
free
Light
...light
archibase planet
lamp lighting light
light - s2 - 3d model for interior 3d visualization.
archibase_planet
free
Light
...light
archibase planet
light luminaire lighting
light l0465 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
lighting
...lighting
3dexport
lighting
3d_export
$5
lighting
...lighting
3dexport
lighting in livingroom
turbosquid
$3
Lighting Tree with Lights
...d model lighting tree with lights for download as max and 3ds on turbosquid: 3d models for games, architecture, videos. (1585507)
archibase_planet
free
Light
...light
archibase planet
luster lighting solution
light - s - 3d model for interior 3d visualization.
archibase_planet
free
Light
...light
archibase planet
luster lamp lighting
light 1 - 3d model for interior 3d visualization.
archibase_planet
free
Lights
...lights
archibase planet
surgical lights surgical lamp
surgical lights (floor) - 3d model for interior 3d visualization.
archibase_planet
free
Light
...light
archibase planet
lighting luminaire candlelight
light l0463 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$18
street light-lighting-light-xia bing
...
3dexport
street light-lighting-light-xia bing<br>max 2015 v-ray 3 max 2015<br>textures<br>all files in zip...