Thingiverse
Beastgrip Remix MK3 by sketchpunk
by Thingiverse
Last crawled date: 3 years, 1 month ago
Video Demo : https://www.youtube.com/watch?v=tM8tXBGBS7w
UPDATE 05/24/16==================
Created a new handle for the rig, plus cable holder to keep the wire nice and neat to connect the button to the phone. Also updated the lens slider. Overall some improvement but still not happy with the handle, its not very comfortable to hold, plus the lens module is a pain to put together. So those two areas need some redesigning.
Here is the 3rd attempt at creating a custom beastgrip like rig that turns a phone into a camera. This attempt merged the ideas I had from MK1 and MK2 into a nice simple yet very modular design. Going back to an all threaded setup seemed like a better choice since it allows the parts to be very well tighten together to keep things from bouncing around compared to MK2's thumb screw tightening which is much more beastgrip like. Ideally once the rig is setup for a phone, there is no need to really adjust it, so making it tight makes it easier to just slap on the phone and get to work.
MK3, I was finally able to introduce the shutter button mechanics which is really the big selling point for me. MK1 and 2 was just not good enough so I never bothered, but mk3 is finally a very stable rig that I finally took it a step further with a shutter button. Its pretty easy to make one, just need a TRRS mount and a 200ohm resister between pole 4 and ground with the button allowing electricity to flow when you want to take a picture. What this does is tell the phone that you are pressing the up volume button which Vol Up/Down for camera apps trigger's the shutter.
Another feature is being able to creating the rig at what vertical length you need. For my rig i wanted it to be as small as possible BUT at the same time when I get a newer phone that might be bigger I can still adjust the height of the rig for it to fit. So by using through hole standoffs and long M3 screws, I am able to set the overall height of the rig. Length wise, I just bought 3 feet long threaded rods and cut them to the exact length I want the rig to be.
There are many ways to make the vertical rods. You can use long screws and short standoffs, or you can make the screws shorter but the standoffs longer. You can even use different types of standoffs. Another way is to use two screws with a coupler to hold them together. OR just buy a bunch of threaded rods for real cheap and cut to length exactly what you need and just use M3 nuts to tighten it to the 3d printed parts. So how to build it is up to you, depends on what you have at hand Or how you want it to kind of look like.
Needed Parts
Step-Down Adapter Ring 46mm Lens to 37mm (Needed to mount lenses)http://amzn.to/1P5LpsJ
M3 Nutshttp://amzn.to/229gd8L
M3 Rods
Regular steel, very cheap and what I used on the prototype. With 50 cents a rod, you can pretty much just use this and a mini hacksaw or dremel to cut the lengths of both horizontal and vertical screws. I am also posting stronger grade rods if you want a more solid feel but it'll cost you a bit more.
https://www.zoro.com/value-brand-threaded-rod-steel-m3-05x3-ft-m203000301000/i/G9804453/
https://www.zoro.com/value-brand-threaded-rod-a2-ss-m3-05x1m-m510700301000/i/G9463072/
https://www.zoro.com/value-brand-threaded-rod-a4-ss-m3-05x3-ft-150794/i/G9051165/
Buttonshttp://amzn.to/1Xlng7ohttp://amzn.to/1Xlniwbhttp://amzn.to/1Xlnz1V
4 Pole Coiled Headphone cablehttp://www.ebay.com/itm/3ft-4-Pole-Spring-Coiled-3-5mm-Aux-Cable-w-Mic-Gold-Stereo-Audio-Auxiliary-Cord-/151917166186?hash=item235ef7fe6a:g:BXYAAOSwP~tW4zDW
TRRS Jack (I used an SMD i had, but you can probably use something else as long as its TRRS). Also just grab a 200ohm resister.http://amzn.to/1XloHTm
Possible screws to use
M3 x 80mm screwshttp://amzn.to/1pDCw4S
M3 x 70mm screwshttp://amzn.to/1Xll5AT
M3 x 60mm screwshttp://amzn.to/1Xllao4
Different Standoffs you can use
M3 x 6mm standoffhttp://amzn.to/1P5Leh1
M3 X 40mm standoffhttp://amzn.to/1XllByL
Round Standoff, Stainless Steel 45mmhttp://amzn.to/1P5LD33
Supporthttps://www.patreon.com/sketchpunk
UPDATE 05/24/16==================
Created a new handle for the rig, plus cable holder to keep the wire nice and neat to connect the button to the phone. Also updated the lens slider. Overall some improvement but still not happy with the handle, its not very comfortable to hold, plus the lens module is a pain to put together. So those two areas need some redesigning.
Here is the 3rd attempt at creating a custom beastgrip like rig that turns a phone into a camera. This attempt merged the ideas I had from MK1 and MK2 into a nice simple yet very modular design. Going back to an all threaded setup seemed like a better choice since it allows the parts to be very well tighten together to keep things from bouncing around compared to MK2's thumb screw tightening which is much more beastgrip like. Ideally once the rig is setup for a phone, there is no need to really adjust it, so making it tight makes it easier to just slap on the phone and get to work.
MK3, I was finally able to introduce the shutter button mechanics which is really the big selling point for me. MK1 and 2 was just not good enough so I never bothered, but mk3 is finally a very stable rig that I finally took it a step further with a shutter button. Its pretty easy to make one, just need a TRRS mount and a 200ohm resister between pole 4 and ground with the button allowing electricity to flow when you want to take a picture. What this does is tell the phone that you are pressing the up volume button which Vol Up/Down for camera apps trigger's the shutter.
Another feature is being able to creating the rig at what vertical length you need. For my rig i wanted it to be as small as possible BUT at the same time when I get a newer phone that might be bigger I can still adjust the height of the rig for it to fit. So by using through hole standoffs and long M3 screws, I am able to set the overall height of the rig. Length wise, I just bought 3 feet long threaded rods and cut them to the exact length I want the rig to be.
There are many ways to make the vertical rods. You can use long screws and short standoffs, or you can make the screws shorter but the standoffs longer. You can even use different types of standoffs. Another way is to use two screws with a coupler to hold them together. OR just buy a bunch of threaded rods for real cheap and cut to length exactly what you need and just use M3 nuts to tighten it to the 3d printed parts. So how to build it is up to you, depends on what you have at hand Or how you want it to kind of look like.
Needed Parts
Step-Down Adapter Ring 46mm Lens to 37mm (Needed to mount lenses)http://amzn.to/1P5LpsJ
M3 Nutshttp://amzn.to/229gd8L
M3 Rods
Regular steel, very cheap and what I used on the prototype. With 50 cents a rod, you can pretty much just use this and a mini hacksaw or dremel to cut the lengths of both horizontal and vertical screws. I am also posting stronger grade rods if you want a more solid feel but it'll cost you a bit more.
https://www.zoro.com/value-brand-threaded-rod-steel-m3-05x3-ft-m203000301000/i/G9804453/
https://www.zoro.com/value-brand-threaded-rod-a2-ss-m3-05x1m-m510700301000/i/G9463072/
https://www.zoro.com/value-brand-threaded-rod-a4-ss-m3-05x3-ft-150794/i/G9051165/
Buttonshttp://amzn.to/1Xlng7ohttp://amzn.to/1Xlniwbhttp://amzn.to/1Xlnz1V
4 Pole Coiled Headphone cablehttp://www.ebay.com/itm/3ft-4-Pole-Spring-Coiled-3-5mm-Aux-Cable-w-Mic-Gold-Stereo-Audio-Auxiliary-Cord-/151917166186?hash=item235ef7fe6a:g:BXYAAOSwP~tW4zDW
TRRS Jack (I used an SMD i had, but you can probably use something else as long as its TRRS). Also just grab a 200ohm resister.http://amzn.to/1XloHTm
Possible screws to use
M3 x 80mm screwshttp://amzn.to/1pDCw4S
M3 x 70mm screwshttp://amzn.to/1Xll5AT
M3 x 60mm screwshttp://amzn.to/1Xllao4
Different Standoffs you can use
M3 x 6mm standoffhttp://amzn.to/1P5Leh1
M3 X 40mm standoffhttp://amzn.to/1XllByL
Round Standoff, Stainless Steel 45mmhttp://amzn.to/1P5LD33
Supporthttps://www.patreon.com/sketchpunk
Similar models
thingiverse
free
Cub Cadet 2000 Series Deck Height Button
...old up fine so far. the button is not threaded so what i did was just screw the button onto the threaded rod to make the threads.
thingiverse
free
Standoff Length Reduction Tool by elevenquad
... and 4 with the adequate
you should now have a standoff length of 22mm (picture 7). tip: better to have a bit shorter than longer
thingiverse
free
Kick Scooter by TreibAir
... a threads for the axles, screwed in the threaded rod and then cut it to length with a handsaw. the handlear parts were glued in.
thingiverse
free
Adjustable PCB Holder for Stencil Printer
...tip under 1.6mm.
if your stencil printer has no holes on the bed to attach the pcb holder you may need to use tape to secure it.
thingiverse
free
Threaded Rod Cap by andrerc
...st screw on to the threaded rods.
if you print this be sure to leave a comment or a make on what was good and what i can improve.
thingiverse
free
prusa mk3 z-axis connector by joost_
...ww.aliexpress.com/item/stainless-steel-8mm-t8x2-lead-screw-threaded-rod-t8-trapezoidal-150-200-250-300-400-500mm/32809280469.html
thingiverse
free
Beastgrip Remix by sketchpunk
...red around photographing :)
small youtube video about it.https://www.youtube.com/watch?v=g6gwaz9hluy
freecad source included.
thingiverse
free
Bed phone holder by lenalebt
...screws
2x m4 nuts
if you want to: 4x m6, 2x m4 washers (i did not use any)
4x 10mm neodym magnets (use the strongest you can get)
thingiverse
free
Parametric Shutter Glasses by psync
... m3 x 15 mm screws if printing the stls as-is, or just modify the openscad to match the diameter and length of whatever you need.
thingiverse
free
google aiy skeleton case by nikki81
...le aiy voice kit
10x10mm m3 bolts
4xm3 nuts
3x15mm m3 threaded rod
8x6mm standered pcb standoffs and screws
6x60mm m3 standoffs
Beastgrip
thingiverse
free
weight form for Beastgrip by maxer_MD
...harp knife.
then turn the lead into it.
take care with the hot lead!
i shoot with the glidecam and needed minimum 1 kg of weight.
thingiverse
free
BeastGrip's Remix Lens Holder by amats
...ngiverse
it's a more stiff holder, using 4 x m3 screws and nuts to hold the 37mm ring in place. haven't tried it yet!!!!
thingiverse
free
Beastgrip Remix by sketchpunk
...red around photographing :)
small youtube video about it.https://www.youtube.com/watch?v=g6gwaz9hluy
freecad source included.
thingiverse
free
Smartphone Camera Rig Basic/ Beastgrip by PublicUniverse
...picatinny mounts to support a mic and flash. adding a tripod mount was never considered, but can possibly be done at a later date
thingiverse
free
Beastgrip Remix MK2 (In Development) by sketchpunk
...well in the first two iterations of the vr goggles i made. so this frame design would be a perfect method to finish that project.
thingiverse
free
UPDATED!!!! Follow Focus + Lens Holder Kit for 8mm rods (rail setup) 48mm wide by amats
...8mm 48mm spaced rods/rails, personally i designed it for beastgrip#39;s hack edition. the lense's gear is specifically designed and...
thingiverse
free
Lens DOF (Depth of Field) Adapter Rings set & Threaded Adapters by amats
...of rings which i designed for a replacement of beastgrip#39;s dof adapter. the main body is 60mm id and...
grabcad
free
Sony RX0ii Accessories
...filters so that they don't cause vignetting on the beastgrip 0.6x wide angle...
Sketchpunk
thingiverse
free
The Flash Magnetic Symbol by sketchpunk
...ws8p8haq
support sketchpunk labs
patreon - https://www.patreon.com/sketchpunk
amazon shop - http://astore.amazon.com/sketclabs-20
thingiverse
free
Foldable Mini Tripod by sketchpunk
...needs a lil tripod, enjoy.
things needed, 1/4 bolt and nut. m3 - 20mm screw and nut.
support : https://www.patreon.com/sketchpunk
thingiverse
free
Glue Stick holder/dispenser(inspired By sketchpunk) by SupremePL45M4
...://www.thingiverse.com/thing:618508).
warning: may clog up a bit, please refine this to make it better
thanks for downloading ;)
thingiverse
free
Cold Steel Bokken Tsuba - Batman by sketchpunk
...ld steel bokken tsuba - batman by sketchpunk
thingiverse
here's a cool tsuba using the batman logo. freecad source included.
thingiverse
free
Cold Steel Bokken Tsuba - Owl by sketchpunk
...d steel bokken tsuba - owl by sketchpunk
thingiverse
here's another tsuba, this time an owl design. freecad source included.
thingiverse
free
Cold Steel Bokken Tsuba - Iron Cross by sketchpunk
... bokken tsuba - iron cross by sketchpunk
thingiverse
using the template, i created an iron cross tsuba. freecad source included.
thingiverse
free
Mechanical Iris by sketchpunk
...l-irirs/
support sketchpunk labs
patreon - https://www.patreon.com/sketchpunk
amazon shop - http://astore.amazon.com/sketclabs-20
thingiverse
free
The qInch Project : Clamp by sketchpunk
... arm using qinch parts.
hardware needed
two 1/4-20 bolts of whatever length you need.
four bolts
freecad source included.
thingiverse
free
Battery Holder / Dispenser by sketchpunk
...ree angle, which i think its mostly my printer or material. might try again with a higher angle.
freecad source files included.
thingiverse
free
Deadpool Magnetic Symbol by sketchpunk
...12f89e16
support sketchpunk labs
patreon - https://www.patreon.com/sketchpunk
amazon shop - http://astore.amazon.com/sketclabs-20
Mk3
turbosquid
$50
cention mk3
...ty free 3d model cention mk3 for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1454148)
turbosquid
$129
MK3 Tank
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$100
Toyota Supra MK3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$44
cention mk3 low poly
...d model cention mk3 low poly for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1454666)
turbosquid
$30
Challenger I Mk3 Falcon
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
American Frag hand grenade MK3
...free 3d model american frag hand grenade mk3 for download as on turbosquid: 3d models for games, architecture, videos. (1393624)
turbosquid
$20
Mk3 US Navy Combat Knife
...ty free 3d model mk3 us navy combat knife for download as fbx on turbosquid: 3d models for games, architecture, videos. (1172791)
3d_export
$29
Ford Fiesta MK3 Modified 3D Model
...7 tumerfx mtumer mehmet t?mer 1993 1995 1996 wrc special modifed modifiye
ford fiesta mk3 modified 3d model mtumer 30698 3dexport
3d_export
$99
Toyota Supra Mk3 19861993 3D Model
...ort fast coupe japan 1986 1987 1988 1989 1990 1991 1992 1993 tuning turbo
toyota supra mk3 19861993 3d model squir 62530 3dexport
turbosquid
$5
Timothy Oulton Mars Chair MK3
...on mars chair mk3 for download as 3ds, max, obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1209782)
Remix
turbosquid
$5
MODA Collection Remix Chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$12
remix yamaha rm1x
...remix yamaha rm1x
3dexport
geometry triangles 15.2k vertices 7.6k pbr no textures 1 materials 1 uv layers yes
3d_ocean
$5
Vray fabric Kvadrat remix green - tileable
...th vray and 3dsmax. high-resolution texture images (2000×2000 px) file included: shader vray 2.40 texture image 3ds max 2011 file
turbosquid
$20
Gerrit Rietveld 1938 Zig Zag Chair Remix
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
multicolored remix parametric table furniture
... fbx, obj, mtl, archive with textures. the model has no glitches. render and materials - vray . without using plugins. good use!
3ddd
$1
Barovier&Toso / Manhattan Remix 7192
... 004293-142405
в коллекции есть люстры 7, 9, 12 рожковые. диаметр соответственный 1000, 1250, 1500 мм.
3ddd
$1
Muuto fiber chair
...grey/grey, dusty green/dusty green, nature/oak, natural white/oak upholstery options remix 183/black, remix 133/grey, remix 643/dusty red leather options black...
3ddd
$1
Barovier&Toso 7190-7195
...7190-7195 3ddd barovier&toso потолочнай люстра фабрики barovier&toso;, коллекция manhattan remix артикул 7190-7195. размеры в inches: 39"...
3d_export
$5
3D Locking Handle Weatherproof Storage Box Container
...handle weatherproof storage box container 3dexport new, improved and remixd! no screws required. print-in-place. weatherproof. parametric. 2 parts. easy...
cg_studio
$49
HTC One Mini 2 Amber Gold3d model
...cell phone mobile cellular super lcd touchscreen touch screen remix amber gold .max .obj .mb .lwo .fbx .c4d .3ds...