Thingiverse
Bearing Protector Trek 5900 by elhalpern
by Thingiverse
Last crawled date: 3 years ago
This accessory only fits a small number of Trek OCLV full carbon fames/forks. The 5900 model was the top of the line bike that was ridden in the Tour de France in 2003/2004 and cost over $3000 in those years. This is NOT designed to fit Trek's OCLV 5000, 5020, 5200 or 5500 series frames/forks.
The headset on my 2003-2004 Trek 5900 was overdue for replacement and I’d stopped riding it because it had a very obvious center “detent.” I had read that this model had a tapered steering tube but wasn’t sure until I took it apart. I’d also read that this design suffered from corrosion.
I expected the fork to just drop once I unscrewed and removed the center screw & top- cap and loosened the two cross-bolts on the stem. With the center cap & screw and the stem/bars removed the fork just stayed in place. I hit the top of the steering tube with a nylon hammer while supporting the top and head tubes and nothing happened. I got that oh-shit feeling, like what is it going to take to disassemble this.
After removing the stem spacers and the split-beveled centering-washer things still didn’t move with a nylon hammer hit. I then gave the steering tube one shot of “PB Blaster” so it would run down the steering tube and penetrate the bottom bearing. I came back a day later, hit it again with the nylon hammer and the fork dropped out with the bottom bearing firmly attached to the fork-crown.
On this aluminum/composite fork the “fork-crown” is a thin ring that’s about 1mm thick and provides a 2mm annular ring. ( see photos )
Next I needed to remove the old bearing and found that the inner ring of the bearing was wide enough to use a large flat-blade screwdriver, a hammer, and soft pine-wood block to cushion the hammer blows. With the fork upside-down I gave a hit on the front of the fork, then one on the back, rotating the fork 180 degrees for each hit to walk the dead bearing down about 1.5 inches until it just fell off the steering tube.
A little re-cap here. The fork and it’s bottom sealed bearing remove as one piece. The bottom headset cup is a snug fit for the outer ring of the bearing and this cup stays with the frame. The top and bottom sealed bearings are a snug fit in the cups that are bonded (glued) to the frame's head-tube.
The steering tube on my fork had lots of surface oxidation, but was otherwise in good shape, unlike pictures of some I've seen posted.
The top surface of the larger bottom bearing had significant rust on it but still looked usable… as if the balls and bearing surfaces inside were still good. They weren’t… this sealed bearing was shot. The rust on the bearing looked like water had made it up around the edges of the bottom cup rusted and dried out on top of the bearing. There was also some rust film on the lowest area inside of the carbon fiber head tube. Seeing this drove me to devise some protector.
So I got out my dial calipers and took measurements, writing down the I.D and O.D of both sealed bearings and the steering tube at the top and the bottom. The top bearing was in good shape and I just need a new bottom bearing. These bearing are not proprietary and once you know their dimensions (ID/OD/Thickness) you can source them anywhere. A bit of internet searching made me realize that the bearing isn't unique, but very much off the shelf if you know what’s needed.
I ended up buy a pair of replacement lower bearings from one eBay seller in the USA, and from one eBay seller in Hong Kong. The USA part arrived in 9-days and was about $22 with shipping and had the Enduro brand name on its rubber seals. The Hong Kong part was about $11 delivered and hasn’t arrived yet (two full weeks & counting). Both bearing had identical published dimensions, and the picture of both made it look like the inner ring had a slight “chamfer” making it easier to install or remove. The inner ring of the Enduro bearing did NOT have any chamfer on it. So much for the picture...
Before installing the new lower bearing I decided to clean up the steering tube using a Harbor Freight buffing wheel in my drill-press and brown-rouge. This got much of the tube to almost a mirror finish.
Next I slid the new bearing down the steering tube and used a piece a 1.75” ID schecule-40 PVC pipe as a tool to slam the new bearing into place. This didn’t work and the sharp edge of the Enduro bearing literally shaved off a few hundredths of a millimeter (less than a human hair). Rather than muscle the bearing into place and let the bearing shave the steering tube I decided to remove the new bearing with a hammer and screw-driver as I’d done with the old (bad) bearing and get out some 220 grit sand paper.
I paused at this moment to wonder how Trek handled this when the frames where being built up? Was the bevel of the original bearing enough to allow easy assembly? Perhaps the newly made steering tubes were completely free of oxidation? Perhaps Trek chilled the fork tube to shrink it and rammed a room temperature bearing onto the cold tube? Someone at Trek 20 years ago knows the answer.
I used a 2x6x8 inch piece of wood and a forstner wood bit that matched the diameter of the top of the steering tube. This allowed me to twist the steering tube snugly into the cross-hole of the 2x6 and clamp the 2x6 into a bench vise so the fork was horizontal. I created sandpaper strips of 220, 400, & 600 grit that were folded over and about 8 x ½ inch long. I used these like a shoe-shiner’s towel to sand away high spots and turn the fork 90 degrees at a time to remove the shavings and any marks made by installing the new bearing. I repeatedly installed the bearing to be snug enough that it would scratch the steering tube, then removed the bearing and sanded just to remove the scratch marks it left behind. This way the sanding wouldn't make the steerer egg-shaped. After about 20-30 minutes I had the bearing within ¼ inch of being fully seated. i cleaned the sanded aluminum tube with alcohol after each sanding volley.
Before the final installation of the bearing to its full down position I rolled an o-ring (3.5mm thick x 30mm ID x 36.5mm OD) all the way down the steering tube, over the tiny fork-crown and had it come to a rest under the fork-crown and well above the front brake mounting hole. The o-ring came in an assortment pack from a local AutoZone store.
This o-ring was installed as part of a 3D printed mini-fender assembly to protect the new bearing from road dirt and water kicked up by the front tire.
The 3D printed split mini-fender holds itself into place by friction encircling the o-ring and still leaves a 1.5mm gap between the top of the 3D printed parts and the bottom (outside) seal of the lower bearing.
Before doing the final reassembly I gave the top of the lower bearing and the entire steering tube a thin coating of Phil Wood’s green waterproof grease to protect it from future corrosion. I also inspected the o-ring that is built into the upper top cup/cover and painted that o-ring with Phil’s grease as well. Also painted the inside of the steering tube above the star-fangled nut and also painted its threads.
Doing the final assembly of the top bearing, its split-beveled washer, the stem spacers, the stem, and the center screw/cap I used a lot of Phil’s grease to keep moisture out. Going a bit further I put a thin bead of clear silicone caulk under the outer edge of the top cap and around the center screw to keep moisture out. With everything back together and adjusted I used more clear silicone and loaded up the pinch-slot on the back of the stem to keep water and sweat from getting it.
Before the lower bearing was ever an issue and the 5900 was new to me, I knew I needed to keep moisture out of the head-tube and headset bearings. While the lower bearing was shot, but the clear silicone I used years ago kept the damage from being much worse.
And that’s the whole story that led to this odd 3D printed protector.
The protector itself is held in place by the o-ring and the alignment fingers at the narrow part of this mini-fender. Three inner-tube slices (rubber bands) cut from an 18-25mm butyl inner-tube are used on the nail-head features I designed into the 3D model.
The fender works as planned and it can be removed or reinstalled as needed. The o-ring can only be installed while the fork is out and does NOT have its bearings in place. However, the o-ring can be removed with an x-acto knife if you just want it to be gone.
The 3D Printed part protects the bearing from head-on rain, and has a v-shaped drain detail at the back to keep water from being trapped, and it is open on the sides to allow it to breath and stay dry. The fender section keeps water and dirt from being splashed at the bearing.
I just road the 5900 for the first time in 4-years with its new lower headset bearing, the prototype bearing fender, and the cleaned and repainted front brake-cable stop and top tube area. All is good and I thought other 5900 owners would benefit from my craziness.
FYI – one of the bikes sold from Robin Williams estate was a Trek 5900 that he acquired while following Lance on some of his races.
The headset on my 2003-2004 Trek 5900 was overdue for replacement and I’d stopped riding it because it had a very obvious center “detent.” I had read that this model had a tapered steering tube but wasn’t sure until I took it apart. I’d also read that this design suffered from corrosion.
I expected the fork to just drop once I unscrewed and removed the center screw & top- cap and loosened the two cross-bolts on the stem. With the center cap & screw and the stem/bars removed the fork just stayed in place. I hit the top of the steering tube with a nylon hammer while supporting the top and head tubes and nothing happened. I got that oh-shit feeling, like what is it going to take to disassemble this.
After removing the stem spacers and the split-beveled centering-washer things still didn’t move with a nylon hammer hit. I then gave the steering tube one shot of “PB Blaster” so it would run down the steering tube and penetrate the bottom bearing. I came back a day later, hit it again with the nylon hammer and the fork dropped out with the bottom bearing firmly attached to the fork-crown.
On this aluminum/composite fork the “fork-crown” is a thin ring that’s about 1mm thick and provides a 2mm annular ring. ( see photos )
Next I needed to remove the old bearing and found that the inner ring of the bearing was wide enough to use a large flat-blade screwdriver, a hammer, and soft pine-wood block to cushion the hammer blows. With the fork upside-down I gave a hit on the front of the fork, then one on the back, rotating the fork 180 degrees for each hit to walk the dead bearing down about 1.5 inches until it just fell off the steering tube.
A little re-cap here. The fork and it’s bottom sealed bearing remove as one piece. The bottom headset cup is a snug fit for the outer ring of the bearing and this cup stays with the frame. The top and bottom sealed bearings are a snug fit in the cups that are bonded (glued) to the frame's head-tube.
The steering tube on my fork had lots of surface oxidation, but was otherwise in good shape, unlike pictures of some I've seen posted.
The top surface of the larger bottom bearing had significant rust on it but still looked usable… as if the balls and bearing surfaces inside were still good. They weren’t… this sealed bearing was shot. The rust on the bearing looked like water had made it up around the edges of the bottom cup rusted and dried out on top of the bearing. There was also some rust film on the lowest area inside of the carbon fiber head tube. Seeing this drove me to devise some protector.
So I got out my dial calipers and took measurements, writing down the I.D and O.D of both sealed bearings and the steering tube at the top and the bottom. The top bearing was in good shape and I just need a new bottom bearing. These bearing are not proprietary and once you know their dimensions (ID/OD/Thickness) you can source them anywhere. A bit of internet searching made me realize that the bearing isn't unique, but very much off the shelf if you know what’s needed.
I ended up buy a pair of replacement lower bearings from one eBay seller in the USA, and from one eBay seller in Hong Kong. The USA part arrived in 9-days and was about $22 with shipping and had the Enduro brand name on its rubber seals. The Hong Kong part was about $11 delivered and hasn’t arrived yet (two full weeks & counting). Both bearing had identical published dimensions, and the picture of both made it look like the inner ring had a slight “chamfer” making it easier to install or remove. The inner ring of the Enduro bearing did NOT have any chamfer on it. So much for the picture...
Before installing the new lower bearing I decided to clean up the steering tube using a Harbor Freight buffing wheel in my drill-press and brown-rouge. This got much of the tube to almost a mirror finish.
Next I slid the new bearing down the steering tube and used a piece a 1.75” ID schecule-40 PVC pipe as a tool to slam the new bearing into place. This didn’t work and the sharp edge of the Enduro bearing literally shaved off a few hundredths of a millimeter (less than a human hair). Rather than muscle the bearing into place and let the bearing shave the steering tube I decided to remove the new bearing with a hammer and screw-driver as I’d done with the old (bad) bearing and get out some 220 grit sand paper.
I paused at this moment to wonder how Trek handled this when the frames where being built up? Was the bevel of the original bearing enough to allow easy assembly? Perhaps the newly made steering tubes were completely free of oxidation? Perhaps Trek chilled the fork tube to shrink it and rammed a room temperature bearing onto the cold tube? Someone at Trek 20 years ago knows the answer.
I used a 2x6x8 inch piece of wood and a forstner wood bit that matched the diameter of the top of the steering tube. This allowed me to twist the steering tube snugly into the cross-hole of the 2x6 and clamp the 2x6 into a bench vise so the fork was horizontal. I created sandpaper strips of 220, 400, & 600 grit that were folded over and about 8 x ½ inch long. I used these like a shoe-shiner’s towel to sand away high spots and turn the fork 90 degrees at a time to remove the shavings and any marks made by installing the new bearing. I repeatedly installed the bearing to be snug enough that it would scratch the steering tube, then removed the bearing and sanded just to remove the scratch marks it left behind. This way the sanding wouldn't make the steerer egg-shaped. After about 20-30 minutes I had the bearing within ¼ inch of being fully seated. i cleaned the sanded aluminum tube with alcohol after each sanding volley.
Before the final installation of the bearing to its full down position I rolled an o-ring (3.5mm thick x 30mm ID x 36.5mm OD) all the way down the steering tube, over the tiny fork-crown and had it come to a rest under the fork-crown and well above the front brake mounting hole. The o-ring came in an assortment pack from a local AutoZone store.
This o-ring was installed as part of a 3D printed mini-fender assembly to protect the new bearing from road dirt and water kicked up by the front tire.
The 3D printed split mini-fender holds itself into place by friction encircling the o-ring and still leaves a 1.5mm gap between the top of the 3D printed parts and the bottom (outside) seal of the lower bearing.
Before doing the final reassembly I gave the top of the lower bearing and the entire steering tube a thin coating of Phil Wood’s green waterproof grease to protect it from future corrosion. I also inspected the o-ring that is built into the upper top cup/cover and painted that o-ring with Phil’s grease as well. Also painted the inside of the steering tube above the star-fangled nut and also painted its threads.
Doing the final assembly of the top bearing, its split-beveled washer, the stem spacers, the stem, and the center screw/cap I used a lot of Phil’s grease to keep moisture out. Going a bit further I put a thin bead of clear silicone caulk under the outer edge of the top cap and around the center screw to keep moisture out. With everything back together and adjusted I used more clear silicone and loaded up the pinch-slot on the back of the stem to keep water and sweat from getting it.
Before the lower bearing was ever an issue and the 5900 was new to me, I knew I needed to keep moisture out of the head-tube and headset bearings. While the lower bearing was shot, but the clear silicone I used years ago kept the damage from being much worse.
And that’s the whole story that led to this odd 3D printed protector.
The protector itself is held in place by the o-ring and the alignment fingers at the narrow part of this mini-fender. Three inner-tube slices (rubber bands) cut from an 18-25mm butyl inner-tube are used on the nail-head features I designed into the 3D model.
The fender works as planned and it can be removed or reinstalled as needed. The o-ring can only be installed while the fork is out and does NOT have its bearings in place. However, the o-ring can be removed with an x-acto knife if you just want it to be gone.
The 3D Printed part protects the bearing from head-on rain, and has a v-shaped drain detail at the back to keep water from being trapped, and it is open on the sides to allow it to breath and stay dry. The fender section keeps water and dirt from being splashed at the bearing.
I just road the 5900 for the first time in 4-years with its new lower headset bearing, the prototype bearing fender, and the cleaned and repainted front brake-cable stop and top tube area. All is good and I thought other 5900 owners would benefit from my craziness.
FYI – one of the bikes sold from Robin Williams estate was a Trek 5900 that he acquired while following Lance on some of his races.
Similar models
thingiverse
free
Bicycle fork steerer tube adapter for maintenance
...and through the headset
remove the fork for maintenance, leaving the scrap steerer in place until you're ready to reassemble.
thingiverse
free
Fork Seal Tool 43 mm by timskloss
...rger tube used as a hammer extension. print very heavy to retain strength. i suggest pet with 2mm of perimeters and 50% infill.
thingiverse
free
Cannondale Headshok installation tool by Allenm00
..., lower the stem, rinse and repeat.
i printed these at 100% infill and had to file the steps on the ramps caused during printing.
thingiverse
free
43mm Fork Seal Driver by WVermaak
... eye out :) if you want other sizes, just give me a comment.
note: you will need to print two halves to fit around the fork tube.
thingiverse
free
Trek 5900 rear-brake cable stop by elhalpern
...e to seal any stray fibers surrounding the hole.
fyi - there is also a lower bearing headset protector design for the trek 5900
thingiverse
free
Self Sealing Stem Bolt by poblockim
...tem bolt by poblockim
thingiverse
here is a self-sealing stem bolt. i made it quickly for my friend from star trek ds9 group \//
thingiverse
free
Lightest fidget spinner bearing remover by AdryJay
...with a better description, because i'm italian and not so good in english language. :-)
please share a photo if you print it!
thingiverse
free
Star Trek DS9 Self Sealing Stem Bolt by randyf
...andyf
thingiverse
a sel-sealing stem bolt from the episode "progress" of star trek
: deep space nine, because why not?
thingiverse
free
hacksaw guide rings for a bicycle carbon fork's steering tube by m013
...e in cura itself
abs is preferred due to heat resistance
not recommended for aluminum tubes, otherwise use cooling or make pauses
thingiverse
free
Sovol SV01 Filament Sensor Mount by maxwiggins
...acket( the old right side bearing area) was not needed so i removed it for less drag. works great!!
thanks to the original maker!
5900
thingiverse
free
One Gauge Marklin 5900 Model Train Track Connector by MileHigh3DII
...e loose and allowing the track to separate and cause derailments. this snaps over the last two ties to keep the tracks together.
thingiverse
free
Trek 5900 rear-brake cable stop by elhalpern
...e to seal any stray fibers surrounding the hole.
fyi - there is also a lower bearing headset protector design for the trek 5900
thingiverse
free
Dial Indicator Mount - Clausing Lathe (5900 Series) by MoxieEngMach
...in petg -petg for both may be better. rotating the mount upside down on the 45°, creates print with minimal supports (as shown).
thingiverse
free
Uck-03f04m Scope uck-03f04m by shivinteger
...& turbosound 1 [!] number of faces #1 : 5900 + number of faces #2 : 100005 = 105905...
Elhalpern
thingiverse
free
Optiplex 160 Stand by elhalpern
...pture slots and grabs the pc more than an inch up its sides. it's a free alternative to dell's # cn-0j163g - j163g
enjoy!
thingiverse
free
Engine Key Briggs & Stratton # 794696 by elhalpern
...
a second version has been uploaded that does not have the support feature for those with resin or sintering printers. 1/27/2020
thingiverse
free
Hyundai Elantra Vent Slide by elhalpern
...vane.
use and install at your own risk. no warranty. user assumes all risk and may freely modify design to suit personal needs.
thingiverse
free
Holder for "Tube cutter hand tool trapezoid blade" by PredatorJr by elhalpern
...d a holder that protects fingers and the blade without changing the set of the filament. just a rubber band to hold it in place.
thingiverse
free
3TTT Stem Plug by elhalpern
...u may need to select metric conversion in slicing software so that it prints the correct size.
keep your stem bolt clean and dry.
thingiverse
free
Engine Key Tecumseh 430492 35062 for Yard Machines 24inch Snow Blower by elhalpern
...rn
thingiverse
replacement key for a yard machines 24" snow blower with a 7hp tecumseh engine key number 430492 or 35062
thingiverse
free
Vent Shield Acer Aspire AXC series by elhalpern
...this shield still allow the cpu to breath, but prevent dust and water mist or droplets from falling directly into the vent holes.
thingiverse
free
Campagnolo Ergo 8 End Cap by elhalpern
...right in and will replace original lost or broken parts. version 2 was uploaded to provide spring clearance for the thumb lever.
thingiverse
free
Honda CRV 02-05 Rear Window Wiper Bridge by elhalpern
...e" solves this issue and protects your rear wiper from getting burnt out or broken and provides reliable rear window wiping.
thingiverse
free
Gerber Baby Food Jar Holder by elhalpern
...s, and anything small. i'm sure some new parent will also appreciate the form and function of this at feeding time. enjoy !
Trek
thingiverse
free
Star Trek Communicator
...star trek communicator
thingiverse
star trek communicator
thingiverse
free
trek jewelry by eletias
...trek jewelry by eletias
thingiverse
trek like jewelry or ornament!
thingiverse
free
Star Trek by dSASQUATCH707
...star trek by dsasquatch707
thingiverse
star trek logo made on solidworks.
thingiverse
free
Star Trek Fluxx, Star Trek: TNG, and Star Trek Bridge Expansion by SaintedDrew
...ek: tng fluxx. there is also room to add the bridge expansion.
i was also able to add the basic rule instructions in the box too.
thingiverse
free
Star Trek Utility by samcolt7445
...star trek utility by samcolt7445
thingiverse
star trek
thingiverse
free
Star Trek Badge by Ashmonster
...star trek badge by ashmonster
thingiverse
star trek
thingiverse
free
Star Trek Logo by AwesomeA
...star trek logo by awesomea
thingiverse
star trek logo
thingiverse
free
Star Trek Discovery Logo
...star trek discovery logo
thingiverse
star trek discovery logo
thingiverse
free
Star Trek Klingon Empire
...star trek klingon empire
thingiverse
star trek klingon empire
thingiverse
free
Star Trek Gryphon by Markopolo
...star trek gryphon by markopolo
thingiverse
star trek gryphon interceptor
Protector
thingiverse
free
corner protector
...corner protector
thingiverse
corner protector
thingiverse
free
Athletic protector
...athletic protector
thingiverse
athletic protector
;-)
thingiverse
free
Protector culata
...protector culata
thingiverse
protector culata motor
thingiverse
free
Protector de Enchufe/ Power Plug Protector by mrozas
...protector de enchufe/ power plug protector by mrozas
thingiverse
protector para enchuge 220v
thingiverse
free
Cogmind - Protector by SharkPrints
...cogmind - protector by sharkprints
thingiverse
protector
thingiverse
free
T16 protector
...t16 protector
thingiverse
i quickly made a gimbal protector that extend to all the switches. printed in tpu.
thingiverse
free
Taranis stick protector by th3code
...ngiverse
taranis stick protector
taranis stick protector
taranis stick protector
taranis stick protector
taranis stick protector
thingiverse
free
ms50 protector by squowse
...ms50 protector by squowse
thingiverse
ms50 protector
thingiverse
free
Drone Motor Protector
...drone motor protector
thingiverse
motor protector
thingiverse
free
Coronavirus protector by Oscar3Dr
...coronavirus protector by oscar3dr
thingiverse
coronavirus protector
Bearing
thingiverse
free
bearing
...bearing
thingiverse
just a bearing i made for fun
thingiverse
free
Bear
...bear
thingiverse
bear i made in tinkercad to see if i could
thingiverse
free
Brown Bear, Brown Bear by morganglass
...brown bear, brown bear by morganglass
thingiverse
brown bear, brown bear
thingiverse
free
care bears sunshine bear by johnboyjr
...care bears sunshine bear by johnboyjr
thingiverse
care bear sunshine bear
thingiverse
free
Bearing by mskokondo
...bearing by mskokondo
thingiverse
working bearing with bearing balls.
thingiverse
free
Bear mom and bear babyV2 by AlexStormND
...com/en/3d-model/art/bear-mom-and-bear-babyv3
bear mom and bear babyv4https://cults3d.com/en/3d-model/art/bear-mom-and-bear-babyv4
thingiverse
free
Bear mom and bear baby by AlexStormND
...om and bear baby by alexstormnd
thingiverse
bear mom and bear baby, you can see my other sculptures at https://t.me/alexstormnd
thingiverse
free
bearing by isaacdrais
...bearing by isaacdrais
thingiverse
bearing
thingiverse
free
Bearings by The_LAB
...bearings by the_lab
thingiverse
bearings
thingiverse
free
Bearing by milad64
...bearing by milad64
thingiverse
bearing