Base with magnets holders

...magnet holder on i3steel by peter_i thingiverse magnet holder for hall sensor based y-endstop on i3steel.

...oduct_498738 you can glue magnets into the base holes, and then you'll be able to use it like the magnet holder from staples.

...side of models on 25mm bases so that a 6mm magnet (1mm thick) can be easily glued in place to hold to model to magnetic surfaces.

...m of the top piece. the print is an easy print if you place the models on the print-bed as shown in the simplify3d picture above.

...agnet in its base. magnet is 12mm in diameter, 1.5mm thick. designed in freecad, so you can modify the magnet pocket dimensions.

...older for tpu winestopper thingiverse made a holder for https://www.thingiverse.com/thing:2328012 magnet used in base is a 8x3mm

...holder charger base for samsung galaxy s10 supporting a magnet usb wire example : https://fr.aliexpress.com/item/32827540314.html

...magnet holder by salavat_ufa90 thingiverse magnet holder for magnets 451524mm.

...rse used hobby store magnets and printed this base to attach automotive door panel to door magnetically replacing brittle clips.

...it to increase glue addesion, same for the interior to stick to the part as much a posible and avoid the magnet geting ripped off

...magnetic memo clip for 6x3mm magnets thingiverse remixed with thinkercad to use it with 6x3mm neodym magnets

...magnet by giacos thingiverse magnet

...t the equipped end of the tool. the side that sticks to the embedded magnet has be to the side facing outside, at the ribbed end.

...ake devilfish) magnet. inhabit the refrigerator in your home. please prepare a magnet of diameter 5mm and height 3mm by yourself.

...or office magnetic clip, that uses 4 5mm x2mm magnets glued into the four holes. just press the top...

...magnetic emoji thingiverse in love emoji for 2x5mm magnets ...

...in the calipers are for inserting magnets. not all magnets will fit, but i think i chose a fairly...

...netic holder (6.3x2.0 magnet) thingiverse this is remix thing from logitech c270 magnetic holder. requires three 6.3x2.0 magnet.

...8x3mm magnets. if printing at 0.2mm layer height, insert magnets in the piece with the spikes at layer 33...

...o stick it to. with this, you can use a 45mm suction cup with a 10mm magnet, and stick any magnetic object to a suckable surface.

...base thingiverse this base helps wedge the end of the tape measure to the floor

... 80mm 3.2mm base with lp kow 250mm 100mm 3.2mm base with lp kow 250mm 150mm 3.2mm base with lp kow 300mm 100mm 3.2mm base with lp

...base by savethemonsters thingiverse base

...base by jesse53 thingiverse base

...base by m2kalista thingiverse base

...base by danielolivier thingiverse base

...base by savethemonsters thingiverse base part

...lamp base thingiverse lamp base

...the lamp base thingiverse the lamp base

...20x20 base thingiverse 20x20 base

...der thingiverse bottom on the holder is sized for a can or bottle. top of the holder is sized for one in a cooler/stubby holder.

...soap holder holder thingiverse it's a holder to hold the famous soap holder.

...bottle holder jar holder can holder thingiverse hole diameter 38.6mm

...spool holder holder by vemotion thingiverse pipe holder (16mm diameter)

...other of invention this is my first creation basically smartphone holder with usb cable holder and key holder i hope you like it

...t; ;) holder for 5 pieces of modular plate holders from dave o https://www.prusaprinters.org/en/prints/15367-modular-plate-holder

...pen holder/card holder by pinky561 thingiverse a pen holder/card holder in one.

...toilet paper holder with phone holder thingiverse toilet paper holder with phone holder

...radio equipment holder and microphone holder thingiverse radio equipment holder and microphone holder

...popsicle holder holder by billiamthesecond thingiverse keep popsicle holders upright so that they can be set...