Thingiverse
Automated Sprouter Parts (remixed)
by Thingiverse
Last crawled date: 4 years, 3 months ago
I decided to redo this old project for a couple of reasons:
I wanted taller legs so I didn't have to position the sprouter at the edge of the shelf for the drain to work right. And I thought the old legs looked a little too skinny and fragile.
I wanted a larger drain hole, so I wanted something the drain tube goes inside of instead of outside of.
I designed my own trays already, so I thought to include them here as well.
As with the old project, what you need to add to make an automated sprouter is:
A laundry room (or some crative equivalent). If you have a washer there, a garden hose "wye" to split off the cold water line.
A clear plastic container or box that is about 10" deep, 11" tall and 16" wide. I'll include a picture of mine.
A length of 1/4" OD low-pressure clear tubing for drainage. You can probably get this at your local hardware store.
A mister kit or parts. I use 1/4" vinyl tubing and the fittings from "mrdrip.com" along with the 3/4 gph barbed mist nozzles. These have removable heads so you can store them in vinegar between uses to prevent or remove scale.
A garden hose interval timer. I set mine to every 3 hours at 3 or 5 minute duration.
Six stainless #4 by 1/2" screws (or longer) with nuts, to attach the legs and drain. I suggest mounting the drain piece first, then drilling through the drain hole into the container.
Scotch Brite pads for the slots of the trays, or to block the holes if you are using a food-grade container with drilled holes as the tray (and in that case a clip to hold the pad in place).
The holes for the drain are 14mm apart on center. The holes for the legs are 125mm apart on each leg, and the distance between the legs (at the container side) is 223mm, but this can be fudged a little since the legs are 2 separate pieces.
I'll attach updated photos and a link to a youtube video once I redo my existing setup. Here is the old one in the mean time: https://www.youtube.com/watch?v=OY2Ezu5GYMo
I wanted taller legs so I didn't have to position the sprouter at the edge of the shelf for the drain to work right. And I thought the old legs looked a little too skinny and fragile.
I wanted a larger drain hole, so I wanted something the drain tube goes inside of instead of outside of.
I designed my own trays already, so I thought to include them here as well.
As with the old project, what you need to add to make an automated sprouter is:
A laundry room (or some crative equivalent). If you have a washer there, a garden hose "wye" to split off the cold water line.
A clear plastic container or box that is about 10" deep, 11" tall and 16" wide. I'll include a picture of mine.
A length of 1/4" OD low-pressure clear tubing for drainage. You can probably get this at your local hardware store.
A mister kit or parts. I use 1/4" vinyl tubing and the fittings from "mrdrip.com" along with the 3/4 gph barbed mist nozzles. These have removable heads so you can store them in vinegar between uses to prevent or remove scale.
A garden hose interval timer. I set mine to every 3 hours at 3 or 5 minute duration.
Six stainless #4 by 1/2" screws (or longer) with nuts, to attach the legs and drain. I suggest mounting the drain piece first, then drilling through the drain hole into the container.
Scotch Brite pads for the slots of the trays, or to block the holes if you are using a food-grade container with drilled holes as the tray (and in that case a clip to hold the pad in place).
The holes for the drain are 14mm apart on center. The holes for the legs are 125mm apart on each leg, and the distance between the legs (at the container side) is 223mm, but this can be fudged a little since the legs are 2 separate pieces.
I'll attach updated photos and a link to a youtube video once I redo my existing setup. Here is the old one in the mean time: https://www.youtube.com/watch?v=OY2Ezu5GYMo
Similar models
thingiverse
free
Sprouter Tray
...ay fits nicely into one half of the existing container i have, so the tray id 176mm long and 126mm wide with 3mm walls and floor.
thingiverse
free
Automated Sprouter parts by chuckv3
...ts). i used bolt depot product# 6902 and 4115 (as pictured).
for complete parts and assembly, please check out the youtube video.
thingiverse
free
Tormach Slant Pro 15L Lathe headstock funnel by WillLyon
...hose and you'll need to drill a hole in the enclosure to pall the hose through. it mounts to an existing bolt on the machine.
thingiverse
free
Dewalt DW735 Dust Port Adapter by laanguiano
...ow 4" dust hoses. mine kept breaking so i decided to build a model.
you will need to drill the holes for the locking spots.
thingiverse
free
Floor Drain for AC hose by AJK1977
...e backside of the cylinder for the hose to fit, the uploaded image is from the wrong angle.
first upload here so i may remix it.
thingiverse
free
Vent fan adaptors for 25mm fan. by TwoBadCatsLLC
... get much airflow from a 3 cfm fan through the 1/2" output. i'm experimenting with a 3/4" and 1" output hole.
thingiverse
free
Pencil Holder Jig by jlpatte2
... guide together. the holes are 8mm diameter, and the centers are 13mm apart. i used a 19/64" index drill to drill the holes.
thingiverse
free
Dishwasher drain hose adapter by delavar
...ing to connect them together. this is a result of my quick design. works good so far.
my dishwasher model is "siemens".
thingiverse
free
Parametric Drill Vacuum Adapter by mkoistinen
... hose size (diameter and socket length), the "window" diameter as well as the shell thickness and the amount of fillet.
thingiverse
free
Drain with hose port
...to make the main wall 4" in diameter, put a hole in it, and added the garden hose thread. also extended the drain main wall.
Sprouter
thingiverse
free
Sprouter by AnsgarSchmidt
...sprouter by ansgarschmidt
thingiverse
first version of a sprout growing system. updates will follow soon, need to test it first.
thingiverse
free
Sprouter Tray
...ay fits nicely into one half of the existing container i have, so the tray id 176mm long and 126mm wide with 3mm walls and floor.
thingiverse
free
Avocado Sprouter by triffid_hunter
...avocado sprouter by triffid_hunter
thingiverse
an adapter between an avocado seed and a cup of water.
note: prints upside-down!
thingiverse
free
Sprouter by dsplawski
...ictured item is a prototype version. i gave the final copy away as soon as i finished it so i don't have any pictures of it.
thingiverse
free
parametric twistoff avocado sprouter for jars by edauksis
...://www.thingiverse.com/thing:4268682/
check the .scad file for parametrization instructions.
the stl fits in a standard to-77 jar
thingiverse
free
Automated Sprouter parts by chuckv3
...ts). i used bolt depot product# 6902 and 4115 (as pictured).
for complete parts and assembly, please check out the youtube video.
thingiverse
free
Sprouter - Lid Strainer & Stand by Paul_Tibble
...rass...https://www.youtube.com/watch?v=0wux2kn3qrc&t=95s
how to sprout broccoli...https://www.youtube.com/watch?v=njqr8ogrt2m
thingiverse
free
Personal Sprouter by chuckv3
...dfoqu
parts: this looks like a very good timer that would work for the gravity-fed options: https://www.amazon.com/dp/b000ujh6hq
thingiverse
free
Avocado Seed Sprouter for Mason Jar by dsplawski
...ld print without supports now because there's only a 30 degree overhang. the support structure is still available in onshape
Automated
turbosquid
$19
Automation for gates
... model automation for gates for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1600153)
turbosquid
$5
Automated Teller Machine
...tomated teller machine for download as c4d, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1677841)
turbosquid
$30
AUTOMATED GUARD STATION
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$19
Drink Automate New
...w office old red retro rust soda store vending vintage
old rusty drink machine, and new shiny. xsi and lvo exported from blender.
evermotion
$10
home automation system 32 am95
...ion system with all textures, shaders and materials.
it is ready to use, just put it into your scene.. evermotion 3d models shop.
evermotion
$10
home automation system 35 am95
...ion system with all textures, shaders and materials.
it is ready to use, just put it into your scene.. evermotion 3d models shop.
evermotion
$10
home automation system 38 am95
...ion system with all textures, shaders and materials.
it is ready to use, just put it into your scene.. evermotion 3d models shop.
evermotion
$10
home automation system 24 am95
...ion system with all textures, shaders and materials.
it is ready to use, just put it into your scene.. evermotion 3d models shop.
evermotion
$10
home automation system 30 am95
...ion system with all textures, shaders and materials.
it is ready to use, just put it into your scene.. evermotion 3d models shop.
evermotion
$10
home automation system 27 am95
...ion system with all textures, shaders and materials.
it is ready to use, just put it into your scene.. evermotion 3d models shop.
Remixed
turbosquid
$5
MODA Collection Remix Chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$12
remix yamaha rm1x
...remix yamaha rm1x
3dexport
geometry triangles 15.2k vertices 7.6k pbr no textures 1 materials 1 uv layers yes
3d_ocean
$5
Vray fabric Kvadrat remix green - tileable
...th vray and 3dsmax. high-resolution texture images (2000×2000 px) file included: shader vray 2.40 texture image 3ds max 2011 file
turbosquid
$20
Gerrit Rietveld 1938 Zig Zag Chair Remix
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
multicolored remix parametric table furniture
... fbx, obj, mtl, archive with textures. the model has no glitches. render and materials - vray . without using plugins. good use!
3ddd
$1
Barovier&Toso / Manhattan Remix 7192
... 004293-142405
в коллекции есть люстры 7, 9, 12 рожковые. диаметр соответственный 1000, 1250, 1500 мм.
3ddd
$1
Muuto fiber chair
...ture/black, nature/oak, remix 133/grey, remix 183/black, remix 643/dusty red, black silk leather/black, cognac silk leather/black
3ddd
$1
Barovier&Toso 7190-7195
...лочнай люстра фабрики barovier&toso;, коллекция manhattan remix, артикул 7190-7195.
размеры в inches: 39" 1/2wх26"h
3d_export
$5
3D Locking Handle Weatherproof Storage Box Container
...handle weatherproof storage box container 3dexport new, improved and remixed no screws required. print-in-place. weatherproof. parametric. 2 parts. easy...
cg_studio
$49
HTC One Mini 2 Amber Gold3d model
...bj .mb .lwo .fbx .c4d .3ds - htc one mini 2 amber gold 3d model, royalty free license available, instant download after purchase.
Parts
3d_export
$5
Parts
...parts
3dexport
parts
3d_export
$5
Part
...part
3dexport
part
3d_export
$5
Part
...part
3dexport
machine part
3d_export
$65
Part
...part
3dexport
simple rendering of the scene file
3d_export
$65
Part
...part
3dexport
simple rendering of the scene file
3d_export
$30
fan part
...fan part
3dexport
this is a part of fan of pedastal
3d_export
$10
machine parts
...machine parts
3dexport
3d part modeling work ,contact for 3d work
turbosquid
$59
Mechanical Part
...id
royalty free 3d model mechanical part for download as c4d on turbosquid: 3d models for games, architecture, videos. (1410833)
turbosquid
$17
Road parts
...bosquid
royalty free 3d model road parts for download as 3ds on turbosquid: 3d models for games, architecture, videos. (1192967)
turbosquid
$9
Cutter Parts
...squid
royalty free 3d model cutter parts for download as stl on turbosquid: 3d models for games, architecture, videos. (1220010)