Thingiverse
Assassin Creed Belt Buckle by cfeniak
by Thingiverse
Last crawled date: 3 years ago
Designed this for a friend that is making a full costume. He is going to drill out the jewel and glue in a fake gem, but you can also paint it with red nail polish.
Printed in PETG. I used 0.2mm layer height but you can use lower if you are patient. Don't use larger.
Instructions:
-Print file and remove brim
-Clean up any "zits" or artifacts on the part
-Curve the flat belt buckle (optional):
-preheat the oven to 400F (205C)
-place buckle in a baking dish lined with Aluminum foil
-put part in oven to soften ~2-3 minutes
-watch constantly, if the thinnest areas get shiny take it out
-lift it by the aluminum foil and place it on a large curved surface (I used a propane tank)
-use oven gloves and press the buckle to shape
-pay attention to the lower A section to make sure the two points are still in alignment and aren't twisted. Mine were slightly off so I heated them with lighter and fixed them.
Painting (optional):
-paint with a metallic grey paint and primer spray
-spray at all angles and apply 3-4 coats, but not too much in one coat as it will hide features. Multiple coats are needed so you don't strip the paint down to the plastic in the following steps.
-allow to fully dry (1 day)
-spray 1 full coat of flat black spray paint on top of the grey
-wait 1 minute for the paint to get slightly tacky (time varies a lot based on the brand)
-dip a rag or "shop towel" in paint thinner and ring it out, then rub the black spray paint off all the raised surfaces. Rubber/latex gloves aren't a bad idea ;)
-use another rag with the same treatment to finish the job and for a brighter metal appearance redo key areas (the first rag will have a lot of black in it)
-let dry fully
Printed in PETG. I used 0.2mm layer height but you can use lower if you are patient. Don't use larger.
Instructions:
-Print file and remove brim
-Clean up any "zits" or artifacts on the part
-Curve the flat belt buckle (optional):
-preheat the oven to 400F (205C)
-place buckle in a baking dish lined with Aluminum foil
-put part in oven to soften ~2-3 minutes
-watch constantly, if the thinnest areas get shiny take it out
-lift it by the aluminum foil and place it on a large curved surface (I used a propane tank)
-use oven gloves and press the buckle to shape
-pay attention to the lower A section to make sure the two points are still in alignment and aren't twisted. Mine were slightly off so I heated them with lighter and fixed them.
Painting (optional):
-paint with a metallic grey paint and primer spray
-spray at all angles and apply 3-4 coats, but not too much in one coat as it will hide features. Multiple coats are needed so you don't strip the paint down to the plastic in the following steps.
-allow to fully dry (1 day)
-spray 1 full coat of flat black spray paint on top of the grey
-wait 1 minute for the paint to get slightly tacky (time varies a lot based on the brand)
-dip a rag or "shop towel" in paint thinner and ring it out, then rub the black spray paint off all the raised surfaces. Rubber/latex gloves aren't a bad idea ;)
-use another rag with the same treatment to finish the job and for a brighter metal appearance redo key areas (the first rag will have a lot of black in it)
-let dry fully
Similar models
thingiverse
free
Dread Pirate Roberts belt buckle
...t;
you can find the sword here:https://www.thingiverse.com/thing:3634034
and the sheath:https://www.thingiverse.com/thing:3653412
thingiverse
free
Qi'ra Belt Buckle by balooken
...e) :)
our plan is to attach it to the belt using industrial grade velcro.
good luck, and show me some "made" pictures!
thingiverse
free
Belt Buckle Blank by thejamaicanbanana
...t. you can use the flat one or the curved one, they are usually curved but you might find it harder to work on than the flat one.
cg_trader
$5
Steampunk Bookshelf | 3D
...steampunk bookshelf | 3d
cg trader
spray paint flat black then rub bronze acrylic on the dry spray paint
thingiverse
free
M Bison Belt Buckle (Street Fighter)
...of the outline of the buckle with gold or similar paint 4.) string through a black-colored belt so it...
thingiverse
free
Black Widow Buckle
...be glued into the slots on the front part, and you may not need the "back piece" but i've included it as an option.
thingiverse
free
Belt Buckle (Blank)
...es.
printed on elegoo mars at 0.05 with grey resin.
hydrodipped with blue and purple spray paint.
feel free to ask any questions.
thingiverse
free
Coat belt buckle by leafleft
...coat belt buckle by leafleft
thingiverse
coat belt buckle
thingiverse
free
Minimalist Belt Buckle - remix by MakingJerry
... grip6 belt buckle whereby the belt enters the buckle from the front, instead of from the back. use with 1.5" nylon webbing.
thingiverse
free
Star Lord Belt Buckle by Fixnpixels
...go with the arcade belt. printed in pla, sanded, primered with flat (or matte) paint, silver lacquer paint, and satin clear coat.
Cfeniak
thingiverse
free
Corner Shelf by cfeniak
...cfeniak
thingiverse
corner shelf, sectioned into pieces to fit on my 8"x12" bed. printed in pla, attached with epoxy.
thingiverse
free
Tornado Foosball Rod Holder by cfeniak
...tornado foosball rod holder by cfeniak
thingiverse
used for holding rods for practice shots or goalie wars.
thingiverse
free
Rain Diverter Concept by cfeniak
...nspout to divert rain water to rain barrel.
*** this is a concept only, please use model as inspiration for further development
thingiverse
free
ZMR250 Cable Catch by cfeniak
... power and balance charge cables away from the props. 2mm and 3mm version. best printed in something flexible like abs or petg.
thingiverse
free
Multistar Baby Beast Motor Bell Wrench by cfeniak
...multistar baby beast motor bell wrench by cfeniak
thingiverse
makes removing nyloc prop nuts easier
thingiverse
free
Bowden Tube Holder Accessory by cfeniak
...t with two m3 bolts at 10mm spacing. guides the bowden tube. longer one is the one you need to go with the extruder i designed.
thingiverse
free
Shorter 30mm Fan Shroud for Pico Hot End by cfeniak
...shorter 30mm fan shroud for pico hot end by cfeniak
thingiverse
30mm fan shroud for the pico hotend. print in abs.
thingiverse
free
Big Guy Statue Split by cfeniak
... slic3r. exported as individual files. much more printable, but still needs support.
see source references in original version.
thingiverse
free
Stepper motor feed knob by cfeniak
... designed for use with direct drive filament setups for manually feeding filament. push fit. smaller sized knob is big enough.
thingiverse
free
Fluval Flex aquarium lid prop by cfeniak
...niak
thingiverse
simple lid prop i designed to hold up the fluval flex 32.5 gallon / 123 liter tank lid during maintenance, etc.
Creed
design_connected
$29
Creed Bed
...creed bed
designconnected
minotti creed bed computer generated 3d model. designed by dordoni, rodolfo.
3d_export
$5
assassins creed
...assassins creed
3dexport
assassin
3ddd
$1
Кресло Minotti Creed Small
...oni
кресло minotti creed small
design: rodolfo dordonihttp://www.minotti.com/#/armchairs/creed-small-_en_0_2_14692.html
design_connected
$20
Creed Lounge Sofa
...creed lounge sofa
designconnected
minotti creed lounge sofa computer generated 3d model. designed by dordoni, rodolfo.
3d_export
free
Assassins Creed Axe
...assassins creed axe
3dexport
mb/obj
turbosquid
$35
Minotti creed wood
...3d model minotti creed wood for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1352211)
turbosquid
$25
Minotti Creed Bed
...odel minotti creed bed for download as max, max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1570922)
design_connected
$16
Creed Lounge Little Armchair
... little armchair
designconnected
minotti creed lounge little armchair computer generated 3d model. designed by dordoni, rodolfo.
turbosquid
$29
Assassin's Creed Tomahawk
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
ASSASSINS CREED 3D LOGO
...alty free 3d model assassins creed 3d logo for download as ma on turbosquid: 3d models for games, architecture, videos. (1150803)
Assassin
3d_export
$5
assassins creed
...assassins creed
3dexport
assassin
turbosquid
$15
Assassin
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
assassin
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$25
Character - Assassin
...character - assassin
3dexport
assassin model<br>part of superior five character set.
3d_export
$5
assassins suite
...assassins suite
3dexport
assassins creed suite in blue color,high poly with diffuse and normal maps in obj format.
turbosquid
free
Assassins Blade
...turbosquid
free 3d model assassins blade for download as fbx on turbosquid: 3d models for games, architecture, videos. (1178015)
turbosquid
$60
Ninja Assassin
...uid
royalty free 3d model ninja assassin for download as fbx on turbosquid: 3d models for games, architecture, videos. (1213458)
turbosquid
$20
Assassin Girlrigged
...
royalty free 3d model assassin girl(rigged) for download as on turbosquid: 3d models for games, architecture, videos. (1583017)
turbosquid
$25
Lady Assassin
...yalty free 3d model lady assassin for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1159893)
turbosquid
$45
Assassin Girl
...el assassin girl for download as blend, unitypackage, and fbx on turbosquid: 3d models for games, architecture, videos. (1706147)
Buckle
3ddd
$1
BUCKLE CHAIR
...buckle chair
3ddd
buckle
buckle chair
3ddd
$1
AiveenDaly \ Buckle
...aiveendaly \ buckle
3ddd
aiveendaly , buckle
aiveendaly \ buckle
3d_export
$5
buckle
...port
buckle. this model was created in blender 2.91.<br>model contains: normal map,base color texture and pattern texture.
turbosquid
$1
Buckle
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Double-alkaline buckle
...double-alkaline buckle
3dexport
double-alkaline buckle
3d_export
$10
Plastic Buckle
...plastic buckle
3dexport
3d_export
$5
Plastic Buckle 3D Model
...tic buckle 3d model
3dexport
plastic buckle clothing bags belt military buckle
plastic buckle 3d model sickleadzdk 55860 3dexport
turbosquid
$10
belt buckle
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Plastic Buckle 3D Model
...plastic buckle 3d model
3dexport
plastic buckle belt clipping
plastic buckle 3d model katramadosdimitris 26019 3dexport
turbosquid
$2
Buckle Head Lamp
...d
royalty free 3d model buckle head lamp for download as max on turbosquid: 3d models for games, architecture, videos. (1240255)
Belt
turbosquid
$9
Belt conveyor belt
...t conveyor belt for download as 3ds, ige, obj, stl, and sldas on turbosquid: 3d models for games, architecture, videos. (1226546)
3d_export
$6
belt
...d then comes off and fastens at the front of the seat. version: 2015 units: millimetres x-form: yes polys: 120 950 verts: 163 944
3d_export
$7
belt grinder
...belt grinder
3dexport
belt grinder
3d_export
$5
Belt conveyor
...belt conveyor
3dexport
belt conveyor
3ddd
$1
column belt
...column belt
3ddd
колонна
column belt
turbosquid
$5
Belt
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$5
Leather Belt
...ather belt is created in 3dsmax 2011 and rendered with vray 1.5 and it has all the texture included with the multiple obj format.
3d_ocean
$5
Belt Ring
...belt ring
3docean
belt jewelry ring
belt ring 3d model. total weight 3.5 gram & 1.1 stone size. 3dm and obj file format.
design_connected
$11
Belt Round
...belt round
designconnected
meridiani belt round computer generated 3d model. designed by parisio, andrea.
design_connected
$11
Belt Oval
...belt oval
designconnected
meridiani belt oval computer generated 3d model. designed by parisio, andrea.