Thingiverse
Archery Sight Fiber Optic Pin by doesntfearzeus
by Thingiverse
Last crawled date: 3 years ago
I liked the original sight pin, but I had some inspiration to make one that would holdfit a Fiber Optic pin that was wrapped around the barrel like some commercial sight pins out there.
DO NOT REPAIR THE STL you might lose the tunnels the fiber has to go through near the screw.
I made the original wider, longer, strengthened the center shaftpin hole, moved it a bit more forward to give the fiber more room to flex into the side hole. Note in the photos how the fiber must move from the side hole down to the lowest rung of the spiral and then feed its way up towards the rear of the sight.
In theory this is ambidextrous, but you might want to mirror the model if you are putting it on a left handed riser so the fiber runs on the top and will catch a bit more light. I made it so the fiber path favors a right handed riser (held in left hand)
This is cut for 0.75mm (0.029 inch) fiber optic pins. You can purchase that size on all the normal online retailers. The ones I used are 20cm(8") long and get a little more than half way up the barrel. Longer would be better, but this appears to be enough.
You can print in PLA, I used PLA+ here, but I'm a little worried about the effect of sunlight on it so you might want to try ABS or PETG. I might print a PETG one soon.
I made 2 versions. One the straight one and one the spiral armed version for a bit more flare.
You'll probably need to use something to expand the center fiber hole after printing since it might close up, I used a safety pin on my PLA+. If you print in PETG you might need a tiny drill bit or something. Don't make it too fat or it wont hold the fiber.
I used some heat (hair dryer) to make the fiber a bit more flexible. I've heard too much can turn it very brittle so be gentle with the heat. It should make it more flexible so it will be easier feeding it around the spiral. Broke quite a few fibers in earlier prototypes of this sight, but eventually I got it right thanks to better routing and the help of the heat. I used tiny needle nose pliers to help it along, but it leaves marks on the fiber so be gentle when using pliers. Training it through the center hole is very difficult so you might want to start there and then through the side hole and then to the spiral. Leave a tiny bit sticking out the center pin hole so it can catch just a bit more light in front. I also used a few dabs of hot glue in choice spots to ensure it doesn't unravel. See photos.
I used 3" #8-32 screws. The screw head must be cut off, but not before you use them to screw it into the sight. Be slow about screwing it into the sight and be sure to keep it level and centered.
If you need it for a larger fiber pin let me know and I'll try to look into it. the whole sight will likely have to grow a bit bigger to accommodate such.
DO NOT REPAIR THE STL you might lose the tunnels the fiber has to go through near the screw.
I made the original wider, longer, strengthened the center shaftpin hole, moved it a bit more forward to give the fiber more room to flex into the side hole. Note in the photos how the fiber must move from the side hole down to the lowest rung of the spiral and then feed its way up towards the rear of the sight.
In theory this is ambidextrous, but you might want to mirror the model if you are putting it on a left handed riser so the fiber runs on the top and will catch a bit more light. I made it so the fiber path favors a right handed riser (held in left hand)
This is cut for 0.75mm (0.029 inch) fiber optic pins. You can purchase that size on all the normal online retailers. The ones I used are 20cm(8") long and get a little more than half way up the barrel. Longer would be better, but this appears to be enough.
You can print in PLA, I used PLA+ here, but I'm a little worried about the effect of sunlight on it so you might want to try ABS or PETG. I might print a PETG one soon.
I made 2 versions. One the straight one and one the spiral armed version for a bit more flare.
You'll probably need to use something to expand the center fiber hole after printing since it might close up, I used a safety pin on my PLA+. If you print in PETG you might need a tiny drill bit or something. Don't make it too fat or it wont hold the fiber.
I used some heat (hair dryer) to make the fiber a bit more flexible. I've heard too much can turn it very brittle so be gentle with the heat. It should make it more flexible so it will be easier feeding it around the spiral. Broke quite a few fibers in earlier prototypes of this sight, but eventually I got it right thanks to better routing and the help of the heat. I used tiny needle nose pliers to help it along, but it leaves marks on the fiber so be gentle when using pliers. Training it through the center hole is very difficult so you might want to start there and then through the side hole and then to the spiral. Leave a tiny bit sticking out the center pin hole so it can catch just a bit more light in front. I also used a few dabs of hot glue in choice spots to ensure it doesn't unravel. See photos.
I used 3" #8-32 screws. The screw head must be cut off, but not before you use them to screw it into the sight. Be slow about screwing it into the sight and be sure to keep it level and centered.
If you need it for a larger fiber pin let me know and I'll try to look into it. the whole sight will likely have to grow a bit bigger to accommodate such.
Similar models
thingiverse
free
raspberry pi zero W case by ntchris
...duce some heat while running. but pla should work just fine i believe.
also require 4pcs 2.5mm or 2.6mm , 8mm long tapping screw.
thingiverse
free
Bigshock Rail by Hitokiri_Fox
...le is cleaned up as it was a little tough getting the filament in.
all variations printed on their nose with supports and a raft.
thingiverse
free
Stepper Motor simple covers by groundstriketactical
...d one without. not to long so does not effect heat etc. i've been using mine for a while. pla, pla+,petg or more can be used.
thingiverse
free
Red Ryder "Fiber Sight" and Ghost Ring by Dgarner5005
.... with this design you can still see the old rear sight on the lowest setting but it does not need to be removed. hope you enjoy.
grabcad
free
Trophy Ridge React Pro Bow Sight
...ent movement as well as realistic sight pin adjustment. includes fiber optics and rheostat light in lit and unlit configurations.
thingiverse
free
TM Hi Capa front sight
...th the fiber so it picks up more light, in addition im giving you the .ipt files so you can open it up in inventor and edit it ;)
thingiverse
free
Honda NM4 Windshield Riser by MurdockMake
...riser
again, please print this in abs or petg.
also i would recommend screwing the go pro mount to the riser and also gluing it.
thingiverse
free
Ryobi BT3000 table saw adjustment wheel by incanus
...the handle. use a mallet and a block of wood to lightly tap the wheel onto the center axle before replacing the center hex screw.
thingiverse
free
Stackable bin replacement pins by Edbosgra
...nted a .12mm layer height with a .2mm first layer and used a lot of hairspray on the bed. i used petg to make them a bit tougher.
thingiverse
free
Corner shelf by badook
... strips (adhesive).
print preferably in petg/abs/pla+ if used in the bathroom as hot water might weaken pla.
infill: 10% for petg
Doesntfearzeus
thingiverse
free
Pioneer Wagon - Topless by doesntfearzeus
...rse
wanted a simple version without the roof or roof supports. shifted the boxes around some as well to make it easier to print.
thingiverse
free
Fallout New Vegas Golden Gecko - Fixed by doesntfearzeus
...ecko - fixed by doesntfearzeus
thingiverse
just ran the model through a quick fix program. looks like it should slice/print now.
thingiverse
free
Tortle D&D Mini by doesntfearzeus
... for sculpting the torso grooves, re-sculpting the shell, neck, tail, etc.
uploaded picture of suggested cura 3.2 print settings.
thingiverse
free
Grip6 Narrow Rounded Belt Buckle by doesntfearzeus
...r too.
added rails on the backside for strength and rounded the edges for comfort.
works great, been using it for a week or more.
thingiverse
free
Window Blinds Clip - Taller / Stronger by doesntfearzeus
...ions in other plastics.
07/05/2020: added a new one. even more strength but adding more to the one corner. hasn't broken yet.
thingiverse
free
Aggretsuko - SING! by doesntfearzeus
...gretsuko. if you want to go backward far enough go to the original source model from snowivix to get clean version of the pieces.
thingiverse
free
D&D Spiritual Weapons by doesntfearzeus
... in once scaled up to appropriate size.
photos of prints are a bit rough. think i need a new nozzle after some abrasive filament.
thingiverse
free
Ohmu - Nausicaä of the Valley of the Wind by doesntfearzeus
...f the final result.
if you want me to release the tinkercad model of my modified ohmu version let me know and i can look into it.
thingiverse
free
Bao Dim Sum Basket by doesntfearzeus
...nt-bao-baby-sitting-from-pixar-short-74420
https://www.myminifactory.com/object/3d-print-bao-baby-standing-from-pixar-short-74421
thingiverse
free
Boots - Aarakocra - D&D by doesntfearzeus
... crushing under his boots. no sculpting here, all remixing/blending done in 3d builder.
painting of the mini handled by a friend.
Archery
turbosquid
$3
Archery target
...d model archery target for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1221537)
turbosquid
$1
Archery Target
...el 3d archery target for download as blend, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1587807)
turbosquid
$1
Target for archery
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
SPORT---ARCHERY---Target
...el sport---archery---target for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1552530)
turbosquid
$7
SPORT---ARCHERY---Bow
...model sport---archery---bow for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1552526)
turbosquid
$29
Archery Arm Protector
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$15
Archery Target 3D Model
...cher bowman toxophilite range firing board arrow field hit bullseye dart bulls eye
archery target 3d model firdz3d 90323 3dexport
3d_export
$5
stylized archery target
...lude: -base color -base color with ao -ao -normal opengl -roughness textures format - png textures size 4096 x 4096 px resolution
3d_export
$15
archery
... necessary, just drop your models into the scene, load the texture and start rendering. • no special plugin needed to open scene.
3d_export
$5
Medieval Archery Target low poly 3D Model
...dexport
archery target fantasy medevial medieval game textured
medieval archery target low poly 3d model kmgilbert 35039 3dexport
Sight
3d_export
$10
Sight
...sight
3dexport
sight
3d_ocean
$5
Optic Sight
...t sighting device vision
3d model optic sight by alexrazum vray max materials. higtpoly – max,obj,fbx. lowpoly – max,3ds,obj,fbx.
turbosquid
$3
Sight
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
sight
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Sight 3D Model
...sight 3d model
3dexport
sight
sight 3d model strelok00000 59460 3dexport
turbosquid
$10
Sighting scopes
...id
royalty free 3d model sighting scopes for download as dae on turbosquid: 3d models for games, architecture, videos. (1504230)
turbosquid
$1
Sight Glass
...quid
royalty free 3d model sight glass for download as sldpr on turbosquid: 3d models for games, architecture, videos. (1274472)
turbosquid
$9
weapon sight
...ree 3d model weapon sight for download as blend, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1709288)
turbosquid
$13
Sighting Telescope
...del sighting telescope for download as 3ds, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1189172)
turbosquid
$1
Reflex sight
... 3d model reflex sight for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1315574)
Fiber
turbosquid
$29
fiber-cement
...squid
royalty free 3d model fiber-cement for download as obj on turbosquid: 3d models for games, architecture, videos. (1391259)
turbosquid
free
Fiber optics
...d model fiber optics for download as 3ds, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1211912)
turbosquid
$10
fiber Chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$2
Fiber Textures
...extures. tileable and editable. 512×512 pixel sized. jpg , tga image format given. unlimited color possibilities. stay connected
design_connected
$13
Fiber Wood Rug
...fiber wood rug
designconnected
ligne roset fiber wood rug computer generated 3d model. designed by ligne roset.
turbosquid
$7
Fiber Lounge Chair
...
royalty free 3d model fiber lounge chair for download as max on turbosquid: 3d models for games, architecture, videos. (1658264)
3d_export
$20
fiber optics 3D Model
...l
3dexport
light object lamp home decorative bright table element fiber optics furniture
fiber optics 3d model braz 5913 3dexport
3d_export
$5
Carbon fiber seamless 3D Model
...carbon fiber seamless 3d model
3dexport
carbon fiber seamless texture
carbon fiber seamless 3d model gryxitl 79178 3dexport
turbosquid
$24
CZ01 Fiber Optic1
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Centauro Fiber Sculpture
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Optic
design_connected
$9
Optic
...optic
designconnected
alessi optic computer generated 3d model. designed by colombo, joe.
3ddd
$1
обои OPTIC
...обои optic
3ddd
в архиве текстуры и фото обоев из коллекции optic.
archive3d
free
Optics 3D Model
...optics 3d model
archive3d
optics
optics - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$49
optical eyewear
...id
royalty free 3d model optical eyewear for download as max on turbosquid: 3d models for games, architecture, videos. (1592243)
3d_ocean
$5
optical mouses
...al mouses
3docean
3d models computer electronics mouse
optical mouses 3d models. realistic mouse model. custom and unique design.
turbosquid
$10
Optic cross
...yalty free 3d model optic cross for download as sldas and ige on turbosquid: 3d models for games, architecture, videos. (1683403)
turbosquid
$7
OPTIC Mirror
... free 3d model optic mirror for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1223927)
turbosquid
free
Fiber optics
...d model fiber optics for download as 3ds, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1211912)
turbosquid
$8
Mouse optical
...3d model mouse optical for download as 3ds, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1504476)
turbosquid
free
Optical puzzle
... optical puzzle for download as max, ige, fbx, stl, and sldas on turbosquid: 3d models for games, architecture, videos. (1405925)
Pin
3d_export
$5
Pin
...pin
3dexport
very god pin
3d_ocean
$1
Bowling pins
...e inside of cinema 4d. there are 3 files included : pin.c4d : pins array.c4d : pin.obj pins array is the bowling pins set up i...
3d_ocean
$5
Pins
...v-ray studio render setting ready close-ups camera support polys: low: 6.314 high: 1.681.922 (with turbosmooth modifier) *incl...
turbosquid
$4
pin
...osquid
royalty free 3d model pin for download as 3dm and max on turbosquid: 3d models for games, architecture, videos. (1669685)
3d_ocean
$15
Map Pins
...map pins
3docean
factory kremlin map moscow oil oil-derrick pin pins red russia soviet soviet union star
some stylized map pins.
turbosquid
$9
Pins
...lty free 3d model pins for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1506195)
turbosquid
$35
Pins
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Pin
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Pin
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Pins
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.