Thingiverse
AnisopterH8 by kolergy
by Thingiverse
Last crawled date: 3 years ago
The Anisoptera Racer adapted to fly with the H8 Mini board.
It is expected to be the cheapest FPV nano racer platform capable of full acro! 40 to 50$ to build
V0.13: Modified led cutouts and increased lip.
V0.12: Added 2mm to the wheelbase to give a bit more margin to the props
V0.11: Corrected an error on the previous upgrade @ the arms connections + reinforcments.
V0.10: Increased Bat height due to new boards with integrated bat plug
V0.9_SUMO: Extra strong version for beginners following David's request
V0.9: slight reinforcement of the bottom & added lip to prevent the battery from escaping
V0.8: reinforcement @ the screws & 0.5mm height decrease
V0.7: Suiss cheese version 3.40g
V0.6: weight reduction & clean-up (flat bottom) 4.06g
V0.5: Wire passage for flashing 5.76g
V0.4: Clean-up & weight saving 5.83g - carbon:5.30g
V0.3: Battery space enlarged
V0.2: H8 board is now structural & there is a support for the camera
V0.1: Initial design
Carbon loaded PLA filament was tested on V0.4, it is slightly lighter but it not handling shocks well & was rapidly destroyed.
Part list:
Reuse an old H8 Mini -> Banggood: Eachine H8 Mini
or H8 Mini board -> Banggood: Eachine H8 Mini main board
Propeller/Helices -> Banggood: JJRC 1000 Props
Motors/Moteurs -> Banggood: Hubsan H107C Motors or Amazon: Hubsan H107C Motors
Batteries -> HobbyKing: 260mAh 35c 1s batt
All in one Cam ->Banggood: FX798T 5.8G 25mW 40CH CamBanggood: Eachine TX01 5.8G 25mW 40CH Cam
.
You can as well assemble a camera system yourself for this you will need the following:
Cam -> Banggood: CMOS 170Deg Cam
AV-Transmit/Emmeteur Video -> Banggood: 25mW transmitter
Power module: Pololu 5V Step-Up Voltage Regulator U1V10F5 (Light) or Banggood: Maltek 5V step-up module (heavy)
And finally a 33nf capacitor to be connected on the video power to filter the interferences from the engine.
For the remote control you can use the stock H8 remote but if you want more precision you can go with the Devo 7E which can be modded by the DdeviationTX firmware and the addition of a NRF24L01 to control the H8 as described in DroneGarageBlog
Remote Control: Banggood: Devo 7E Mode2
NRF Module: Banggood: NRF24L01
Configuration:
A webpage explaining the firmware flash of the H8 Mini: Drone garage Bolg
Made in Fablab Artilect: https://artilect.fr/dronelab/
https://www.youtube.com/watch?v=l1kkY5fqE6ohttps://www.youtube.com/watch?v=z-fZyy5z10c
It is expected to be the cheapest FPV nano racer platform capable of full acro! 40 to 50$ to build
V0.13: Modified led cutouts and increased lip.
V0.12: Added 2mm to the wheelbase to give a bit more margin to the props
V0.11: Corrected an error on the previous upgrade @ the arms connections + reinforcments.
V0.10: Increased Bat height due to new boards with integrated bat plug
V0.9_SUMO: Extra strong version for beginners following David's request
V0.9: slight reinforcement of the bottom & added lip to prevent the battery from escaping
V0.8: reinforcement @ the screws & 0.5mm height decrease
V0.7: Suiss cheese version 3.40g
V0.6: weight reduction & clean-up (flat bottom) 4.06g
V0.5: Wire passage for flashing 5.76g
V0.4: Clean-up & weight saving 5.83g - carbon:5.30g
V0.3: Battery space enlarged
V0.2: H8 board is now structural & there is a support for the camera
V0.1: Initial design
Carbon loaded PLA filament was tested on V0.4, it is slightly lighter but it not handling shocks well & was rapidly destroyed.
Part list:
Reuse an old H8 Mini -> Banggood: Eachine H8 Mini
or H8 Mini board -> Banggood: Eachine H8 Mini main board
Propeller/Helices -> Banggood: JJRC 1000 Props
Motors/Moteurs -> Banggood: Hubsan H107C Motors or Amazon: Hubsan H107C Motors
Batteries -> HobbyKing: 260mAh 35c 1s batt
All in one Cam ->Banggood: FX798T 5.8G 25mW 40CH CamBanggood: Eachine TX01 5.8G 25mW 40CH Cam
.
You can as well assemble a camera system yourself for this you will need the following:
Cam -> Banggood: CMOS 170Deg Cam
AV-Transmit/Emmeteur Video -> Banggood: 25mW transmitter
Power module: Pololu 5V Step-Up Voltage Regulator U1V10F5 (Light) or Banggood: Maltek 5V step-up module (heavy)
And finally a 33nf capacitor to be connected on the video power to filter the interferences from the engine.
For the remote control you can use the stock H8 remote but if you want more precision you can go with the Devo 7E which can be modded by the DdeviationTX firmware and the addition of a NRF24L01 to control the H8 as described in DroneGarageBlog
Remote Control: Banggood: Devo 7E Mode2
NRF Module: Banggood: NRF24L01
Configuration:
A webpage explaining the firmware flash of the H8 Mini: Drone garage Bolg
Made in Fablab Artilect: https://artilect.fr/dronelab/
https://www.youtube.com/watch?v=l1kkY5fqE6ohttps://www.youtube.com/watch?v=z-fZyy5z10c
Similar models
thingiverse
free
Hubsan H107C X4 FPV Racer Frame 110 by Hackbert
...h-600mah
1x hubsan h107c x4 (electronic)
4x m3 nylon screws
1x fpv camera fx797t 3-in-1 super mini 5.8g 40ch av video transmitter
thingiverse
free
Whippy Whoop by kolergy
...a brushed quad based on 8.5mm motors with a similar form factor as the tiny whoop which is made...
thingiverse
free
GBMicroFPVDrone v1 by gebeclair
...-h107c-h107d-v252-jdx385-p-88012.html
240mah 1s battery for video
i use a walkera devo 7e transmitter running deviation firmware.
thingiverse
free
GBMicroFPVDrone v1.3 by gebeclair
...verter step up module 1-5v to 5v 500ma
i use a walkera devo 7e transmitter running deviation firmware.
http://byoq.over-blog.com
thingiverse
free
QuickNano by kolergy
...ttp://www.robotshop.com/en/step-up-step-down-voltage-regulator-s7v7f5.html
made in fablab artilect: https://artilect.fr/dronelab/
thingiverse
free
DEVO 7E Antenna Mount by HLMAX
... is a link to the nrf24l01 kit: http://www.banggood.com/devo-transmitter-tuner-modified-for-fbl80-fbl100-wltoys-v922-p-89812.html
thingiverse
free
GBMicroFPVDrone v1.2 by gebeclair
...ted for video) to reduce interferences)
i use a walkera devo 7e transmitter running deviation firmware.
http://byoq.over-blog.com
thingiverse
free
Anisoptera Racer by kolergy
...ect.fr/dronelab/
https://youtu.be/rcjchmlqvywhttps://youtu.be/pnofi0aoptihttps://youtu.be/dbokuyc3jxqhttps://youtu.be/y-fjjdxfxks
thingiverse
free
Support Cam H8 Mini by 0Pascal0
...com/eachine-turbine-qx70-micro-racing-quadcopter-spare-parts-5_8g-25mw-48ch-vtx-520tvl-cmos-14-camera-p-1108075.html?rmmds=search
thingiverse
free
Eachine EF-01 Camera mount for the Eachine E010 quadcopter by slibbinas
...er-rtf-p-1066972.html
camerahttp://www.banggood.com/eachine-ef-01-aio-5_8g-40ch-25mw-vtx-800tvl-13-cmos-fpv-camera-p-1064301.html
Kolergy
thingiverse
free
AirForce Tip by kolergy
...airforce tip by kolergy
thingiverse
end bit to be 3d printed
thingiverse
free
WireGuide V0.9 by kolergy
...wireguide v0.9 by kolergy
thingiverse
wire guide for strong print: http://www.thingiverse.com/thing:329498
thingiverse
free
MiniStruder for uDelta by kolergy
...er for udelta by kolergy
thingiverse
the ministruder adapted to the udelta printer
made in fablab artilect: https://artilect.fr/
thingiverse
free
Frabjous 3mm by kolergy
...jous 3mm by kolergy
thingiverse
a scaled version of http://www.thingiverse.com/thing:12271 to use 3mm plywood or other materials
thingiverse
free
DTE by kolergy
...t;dronons tous ensembles"
aimed at providing access to drone to persons with various handicaps
https://artilect.fr/dronelab/
thingiverse
free
Ball Holder for Magnetic Bearing by kolergy
...ball holder for magnetic bearing by kolergy
thingiverse
to comme soon
thingiverse
free
Tool Holder for the Magnetic Platform by kolergy
...tool holder for the magnetic platform by kolergy
thingiverse
soon to come
thingiverse
free
SR17 Torch Holder V0.9 by kolergy
...sr17 torch holder v0.9 by kolergy
thingiverse
to come soon
thingiverse
free
Springy Clip for uDelta by kolergy
...springy clip for udelta by kolergy
thingiverse
springy clip to reduce play on delta printers adapted to the udelta
thingiverse
free
Micro Scisky Board by kolergy
...micro scisky board by kolergy
thingiverse
open scad model of the naze32 based micro scisky board