Thingiverse
5LayersLoft by bbinnard
by Thingiverse
Last crawled date: 3 years ago
The LED lamp uses the same basic design as https://www.thingiverse.com/thing:2852516, but I replaced the sharp corners by smooth curves by rounding/filleting the 7-sided polygons and using a single Loft surface for the outside shape rather than a series of flat ruled surfaces. This lamp printed in 8 hours 12 minutes using a layer height of 0.200 mm and a print speed of 80 mm/sec. The lamp accommodates either a battery operated or wall powered "puck" LED light. This blog page has links for all the wall powered parts needed and shows how to hook everything up: http://birkbinnard.com/blog/wall-powered-led-lights/. For battery powered puck lights just go to any large home improvement store or simply Google "LED puck light".
Similar models
thingiverse
free
Waves4 by bbinnard
...lights/. for battery powered puck lights just go to any large home improvement store or simply google "led puck light".
thingiverse
free
5Levels by bbinnard
...lights/. for battery powered puck lights just go to any large home improvement store or simply google "led puck light".
thingiverse
free
Maelstrom3
...wall power. this blog page has links for wall powered lights that work well: http://birkbinnard.com/blog/wall-powered-led-lights/
thingiverse
free
Curvy3 by bbinnard
...ot;led puck lights."
it printed in a little less than 15 hours using a print speed of 80 mm/sec and a 0.200 mm layer height.
thingiverse
free
VoronoiLamp1
...wall power. this blog page has links for wall powered lights that work well: http://birkbinnard.com/blog/wall-powered-led-lights/
cults
free
Threadlight1
.../wall-powered-led-lights/.
this print took just under 36 hours using a layer height of 0.140 mm and a print speed of 100 mm/sec.
thingiverse
free
Threadlight1 by bbinnard
...g/wall-powered-led-lights/.
this print took just under 36 hours using a layer height of 0.140 mm and a print speed of 100 mm/sec.
thingiverse
free
Pattern2
...g/wall-powered-led-lights/. it printed in a little over 44 hours using a print speed of 80 mm/sec and a layer height of 0.200 mm.
thingiverse
free
Holeylayers2 by bbinnard
... you can get wall powered lights that are brighter and that work very well: http://birkbinnard.com/blog/wall-powered-led-lights/.
thingiverse
free
QuadTwistLED1 by bbinnard
...ard.com/blog/the-quadruple-twist/
this part printed in 22 hours using a layer height of 0.200 mm and a print speed of 100 mm/sec.
Bbinnard
thingiverse
free
BasketWeave1 by bbinnard
...e1 by bbinnard
thingiverse
extensive info about this part is here: http://birkbinnard.com/blog/from-architecture-to-3d-printing/
thingiverse
free
Wiggle2 by bbinnard
...wiggle2 by bbinnard
thingiverse
large vase approx. 220 mm tall. 12 hours print time with 0.200 mm layer height.
thingiverse
free
Collander by bbinnard
...
thingiverse
this could be a small colander or fruit basket. using a layer height of 0.200 mm it printed in 16 hours 45 minutes.
thingiverse
free
VoronoiBowl4 by bbinnard
...y bbinnard
thingiverse
a smaller, solid-walled version of previous open voronoi parts. print time 17:30 @ 0.200 mm layer height.
thingiverse
free
PipeVase3 by bbinnard
...first of 2 parts with the same shape. next one will have just the ribs. this print took 22 hours with a layer height of 0.200 mm.
thingiverse
free
VoronoiBowl1 by bbinnard
...hingiverse
this medium sized bow printed in about 23 1/2 hours using a layer height of 0.200 mm and a print speed of 100 mm/sec.
thingiverse
free
Wigglevase8 by bbinnard
... this vase is fairly large; the print shown here is scaled down to 65% and took 14.5 hours to print with a 0.200 mm layer height.
thingiverse
free
Planter3 & Tray3 by bbinnard
...amp; tray3 by bbinnard
thingiverse
oval-shaped planter and tray for small plants that may be too large for planter1 or planter2.
thingiverse
free
Round box with top by bbinnard
...round box with top by bbinnard
thingiverse
this round box has a tight fitting lid.
thingiverse
free
WBVase2 by bbinnard
...e same basic geometry but has a different overall shape. it printed in a little less than 20 hours using a 0.200 mm layer height.