Thingiverse
4ch Mosfet Enclosure by truglodite
by Thingiverse
Last crawled date: 3 years, 1 month ago
I designed this thing to mount this 4 channel mosfet driver board to my Ikea Lack enclosure:
https://www.amazon.com/gp/product/B01MRQFYJN/
This allows me to add control of several 12V fans and case lights with Marlin firmware. Of course it can be used for other applications requiring this mosfet driver board. Just FYI, I RE'd this board; it has optocouplers and uses the output supply to drive the fets. So the arduino outputs will be safe, and the fets will run nice and cool.
The box measures close to 75x75x22mm for a slim fit around the board. It has 4mm diameter mounting holes in the base with 40mm spacing. The lid simply snaps in to place. The output hole is filled with an 0.45mm thick wall to eliminate the need for printing with supports; it is easily cut out with a razor after printing. The input cutouts are big enough to fit clip in style input plugs, but I'm using standard Dupont plugs with mine. I added slots for passive cooling. The slots alone are adequate for my application, but comment if you need me to add a lid with a fan port instead.
https://www.amazon.com/gp/product/B01MRQFYJN/
This allows me to add control of several 12V fans and case lights with Marlin firmware. Of course it can be used for other applications requiring this mosfet driver board. Just FYI, I RE'd this board; it has optocouplers and uses the output supply to drive the fets. So the arduino outputs will be safe, and the fets will run nice and cool.
The box measures close to 75x75x22mm for a slim fit around the board. It has 4mm diameter mounting holes in the base with 40mm spacing. The lid simply snaps in to place. The output hole is filled with an 0.45mm thick wall to eliminate the need for printing with supports; it is easily cut out with a razor after printing. The input cutouts are big enough to fit clip in style input plugs, but I'm using standard Dupont plugs with mine. I added slots for passive cooling. The slots alone are adequate for my application, but comment if you need me to add a lid with a fan port instead.
Similar models
thingiverse
free
AM8 Electronics Case - with fan on enclosure lid by bipsen
...an lid (mounted on the outside).
note: i have not printed the dual-fan lid, but it should be possible to mount 2 80mm fans on it.
thingiverse
free
Custom Lulzbot Taz 5 Ramps 1.4 Enclosure by weekend_warrior1999
...lder
panel mount usb
40mm fan and mounting screws
2 40mm fan guards
t nuts and screws for mounting
screws for mounting pcb board.
thingiverse
free
Gen7 80mm fan mount by cae2100
...nts.
if you need a spacer to mount the board to something metalic, like a psu case in my case, just print for space.stl files.
thingiverse
free
External Enclosure for A8 Mainboard and 2x mosfet board by MattKi
...es you can access all of the screw holes for securing your boards!
mirrored relevant changes to the generic project box template.
thingiverse
free
Bigtree GTR v1.0 Enclosure by truglodite
...ter wires should be routed out above the screw terminals (don't cross them over your signals wires on the other side).
enjoy!
thingiverse
free
Anet A8 GT2560 board + 1 Mosfet board Case by printerDave
...o move the fan positioning to where i felt it adequate to keep the board components cool (particularly the fets with heat sinks).
cults
$1
RAMPS 1.x Arduino mounting plate with 60mm integrated fan mount
...ate. it also has an integrated 60mm fan mount for easy application of a cooling spring breeze to your hot drivers and mosfets.
thingiverse
free
Duet Wifi Dual Mosfet Electronics Case 2040 by kuhnikuehnast
...sibility to mount a 80 mm fan.
as the often used screw-holes never fit, designed a hole to fit a press nut which can be glued in.
thingiverse
free
120mm fan mount for Sunhokey Prusa i3 electronics by jihartik
...m3 screws & nuts. the fan is attached with similar screws as well. mounting screws for the electronics board...
thingiverse
free
Double MOSFETs mount by Dinh_D
...e i found from https://www.thingiverse.com/thing:2372385
the slot is an idea i got from https://www.thingiverse.com/thing:1997377
Truglodite
thingiverse
free
RCWL-0516 Cover by truglodite
... made it thin but with some clearance, to save filament and minimize interference. it fits nicely for me printed in abs on my a8.
thingiverse
free
SSR Cover (Remix) by truglodite
.... a pair of zipties may be used to secure the wires in their tubes. sized to work with larger wires and crimp on spade terminals.
thingiverse
free
8mm LED Strip Clip by truglodite
... have to remove the adhesive backing, but loose enough to where you can still slide the strip in even if the adhesive is exposed.
thingiverse
free
Ramps Enclosure Remix (lid pin added) by truglodite
.... so i did this remix to add a flange and holes to accept a pin/bolt that locks the lid shut (so it won't fall from gravity).
thingiverse
free
Keystone Surface Mount (single) by truglodite
...small gap on 2 sides of the keystone's face once installed, but it's barely noticeable and they still hold very securely.
thingiverse
free
Anet A8 20mm Printed Rubber Foot by truglodite
... flat headed screws. i just used some small self tapping flat heads, but a set of machine screws and nuts could also get it done.
thingiverse
free
Micro SD Card Extension, Cards, & Stick Mount by truglodite
... room is for my larger usb3 readers to fit, but the standard usb hole inside secures smaller sticks too. prints without supports.
thingiverse
free
Double Mosfet Box by truglodite
...n to save filament. the dimensions are designed for a 0.45mm printer line width (0.4mm nozzle), but other settings may work fine.
thingiverse
free
IEE VFD Enclosure Control Box by truglodite
...cts where you want a honkin' big vfd with "3 button menus". i made the rear compartment over sized for this reason.
4Ch
thingiverse
free
SwitchIoT 4CH - DIY Sonoff 4CH smart switch (Dimensions of PCB relay module 75x50mm)
... switchiot 4ch is a diy sonoff 4ch smart switch.
this is intended for diy which uses relay module 4ch with dimensions pcb 75x50mm
thingiverse
free
SwitchIoT 4CH - DIY Sonoff 4CH smart switch (Dimensions of PCB relay module 76x56mm)
... switchiot 4ch is a diy sonoff 4ch smart switch.
this is intended for diy which uses relay module 4ch with dimensions pcb 76x56mm
thingiverse
free
Coque arrière Sonoff 4CH R2 by wildur
...ère sonoff 4ch r2 by wildur
thingiverse
coque arrière de sonoff 4ch r2 pour une meilleur intégration dans un tableau électrique.
thingiverse
free
ez uhf lite 4ch case by mariors50
...ez uhf lite 4ch case by mariors50
thingiverse
ez uhf case
thingiverse
free
Remote chacon Di-O 1 & 4ch by fafabienman
... / di-o remote control 1 & 4ch
support mural pour télécommande chacon ou di-o 1 canal et 4 canal
good print
if you like it ;)
thingiverse
free
Arduino Nano HC-06 4CH Relay bace by Micky3711
...uino nano shield, a hc-06 or 05 bluetooth and a 4ch relay so you can control 4 things from a smart phone.
will update photos soon
thingiverse
free
4ch relay controller box by dezeure
...
thingiverse
an enclosed mounting box for a 4 ch relay with remote from aliexpress.
80 x 60 dimensions of case with 4 screw lid.
thingiverse
free
AliExpress 4ch constant current DMX led driver case by defl
...ads at the time of publishing (no affiliation or anything, just for reference): https://www.aliexpress.com/item/32795465426.html
thingiverse
free
Raspberry Pi 3 B/B+ and 4CH Relay
... wrong size relay board, so done this quickly as a universal one, has 3 holes, either side of the original one so should fit most
Mosfet
3d_export
$5
IC SMD Package TO263
...used for different types of semiconductors, such as transistor, mosfet voltage regulators and etcetra. a surface mount device for...
thingiverse
free
Support Mosfet
...support mosfet
thingiverse
support mosfet
remplissage 20%
thingiverse
free
i3 MOSFET Holder / i3 MOSFET Halter by JMDesigns
...i3 mosfet holder / i3 mosfet halter by jmdesigns
thingiverse
i3 mosfet holder / i3 mosfet halter
thingiverse
free
MOSFET Holder / MOSFET Halter 20x20 Extrusion by JMDesigns
...mosfet holder / mosfet halter 20x20 extrusion by jmdesigns
thingiverse
mosfet holder / mosfet halter 20x20 extrusion
thingiverse
free
TO-220 MOSFET Holder
...to-220 mosfet holder
thingiverse
this will hold 3x to-220 mosfets. the mosfets will snap into place.
free3d
free
MOSFET
...mosfet
free3d
metal oxide semiconductor field effect transistor
thingiverse
free
Double Mosfet Holder for Lerdge Mosfet Board by LorDXEO
... board by lordxeo
thingiverse
dual mosfet holder for lergde mosfet modules.
holes for m3 screws, you can also use brass inserts.
thingiverse
free
MOSFET Case by Nbbwarhammer
...mosfet case by nbbwarhammer
thingiverse
a case for mosfet.
thingiverse
free
MOSFET Support
...
2 3mm screws
design
i have uploaded the freecad design that i made, so you can remix it and mod it.
i hope it is useful for you!
thingiverse
free
mosfet holders by paulsonia
...mosfet holders by paulsonia
thingiverse
two mosfet holders
Enclosure
3d_export
free
electrical enclosure
...l enclosure where electrical devices like (relays, contactors, busbars ) are kept in order to protect from hazardous environment.
turbosquid
$100
GPU Enclosure
...yalty free 3d model gpu enclosure for download as obj and stl on turbosquid: 3d models for games, architecture, videos. (1381061)
3d_export
$5
Electrical Enclosure
...ed. also has tower lights attaced on the top.<br>file format that are available:<br>.step<br>.obj<br>.stl
archive3d
free
Enclosure 3D Model
...closure 3d model
archive3d
shower enclosure-acquarius- 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-omega- 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-vega - 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-zenith - 3d model for interior 3d visualization.
turbosquid
$20
shower enclosure
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$14
Dumpster Enclosure
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$25
3d printer enclosure
... model 3d printer enclosure for download as ipt, skp, and fbx on turbosquid: 3d models for games, architecture, videos. (1634310)