Thingiverse
2.4ghz helical high gain beam antenna. by Mchaos
by Thingiverse
Last crawled date: 4 years ago
I designed this 2.4ghz helical beam antenna for my 2.4ghz base station. I used a calculator to give me the specs of the coil. Then I designed the antenna mast and complimentary parts in cad. This way I could ensure the diameter, spacing etc. meets the specs of the antenna calc.
The antenna is somewhere around 15dbi gain. The beam is somewhere in the middle between wide and narrow. I was shooting for something that would work without a tracker.
FYI. I use a a 3d printed adapter called DeWatt here on thingivers to use a 12v Dewalt battery to power the receiver.
Assembly:
You will need some copper wire. I used #14 copper I salvaged from some romex. You need enough to make 10 turns. You will also need a copper board 120mm x 120mm. I used PCB material but you can use any kind of metal you have handy. You will need some coax and sma or rpsma depending on your receiver. You will need a receiver. You can use a module in a google set like fatshark, or you can use the one I have. It is the same one that can be found here https://www.getfpv.com/2-4ghz-a-v-receiver.html they are out of stock but this receiver can be found all over the net. you will also need CA glue for permanent assembly.
you have to print each part, but 2 pcs. of the antenna mast as it takes 2 of these to make a full antenna.
Assembly:
1) Assemble the antenna mast. take the 2 pcs. of mast, and the mast coupler, and use CA glue. Put glue on the coupler, and on the faces of the antenna and push them together. Let this dry.
2) Prep the ground plane. Take the copper board (120mm x 120mm) and drill a 10mm hole in the center. Next take the back plane backer, put the rivit through it. Then put the copper board on it and line everything up square. Mark the hole that is off set from the center. This is the hole for the coax connection. Drill at least a 3.5mm - 4mm hole. Take the rivit out for now. Optionally you can now glue the copper board into the back plane backer. Set aside and let dry.
3) Copper coil. Here is what I did. I took something that was smaller than the antenna mast, in my case, the handle on a leaf rake. I had a broken one, and I cut of the end. About 10". Drill a hole in the center of it that is slightly smaller than 1/4" as best you can. Then put a double sided lag screw, 1/4", or cut the hex head of a 1/4" lag screw. Put the lag screw into a drill and drive it into the broom handle. Drill a hole towards the base of th handle just big enough to put the wire in. Then spin the drill slowly, and using a pair of pliers, hold the copper wire tightly, but with enough slack to let it slip. and allow the coil to wrap tightly. You will need more than 10 wraps. I did at least 15. Next take the coil and turn it on the mast slowly. This will ensure a snug fit. Coil it all the way on. Make sure to leave a half a turn that you bend inward to fit into the capacitive tuning ring. Next, clip the coil 10 full turns from the beginning.
4) Optional - Gluing the swivel mount. If you want to glue the swivel mount to the ground plane backer: put CA glue on swivel mount face. Slide rivet through, and then through the ground plane backer. Line up the mount so that it is 90' vertical, and press together. Once the glue grabs, slide the rivet back out.
5) Assemble antenna: Take rivet, and put through swivel mount and ground plane backer. Slide the capacitive tuning ring and slide it over the rivet. Place some CA glue on end of rivet and push the mast on the rivet. Align the capacitive tuning ring so that it lines up with the end of the groove on the mast, so there is 1 half turn that is flat. The extra bit of copper coil needs to run in this groove to the end. Clip off excess at the end.
6) Coax: Slide coax through the small offset hole in the ground plane backer. Strip about 1/2" of the outer jacket of the coax. Peel back shielding and twist it together off the side. Then strip about 1/4" of the center hot. Solder the shielding to the ground plane copper board. Solder the hot to the end of the coil. (You should Align this when assembling.)
Your antenna is built.
7) mounting on tripod. In the back of the receiver base is a hole that should have 1/4" thread that fits a tripod mount. I couldn't get it to printer great, but you can force it in once and it will thread in easy after that. Attach your tripod mount to the base. Then attach to tripod. Using the hinge pin slide it trough the swivel mount of the antenna and base. Then use the hinge pin rivet to lock it together.
DONE.
4/05/2020 - First test: I tested this in my back yard. I didn't have a lot of room. Lots of trees, but it was a good first test. I flew about 250ft away. Not very far but I can say that there was no flicker or break up at all. Usually there is always some sort of breakup when changing directions. Nothing as long as I was out in front of it. Very clear video. I then flew toward the side of the antenna about 50 feet away from the side of the antenna. As soon as I got to almost 90' from the antenna, I almost lost all video. But once I went back a bit, video came back. So it is definitely directional. I did some quick direction changes and some rolls and the video was rock solid. I flew up about 100 feet, and came back down and the video was rock solid. So far it's working well. I will update with a more extensive range test.
The antenna is somewhere around 15dbi gain. The beam is somewhere in the middle between wide and narrow. I was shooting for something that would work without a tracker.
FYI. I use a a 3d printed adapter called DeWatt here on thingivers to use a 12v Dewalt battery to power the receiver.
Assembly:
You will need some copper wire. I used #14 copper I salvaged from some romex. You need enough to make 10 turns. You will also need a copper board 120mm x 120mm. I used PCB material but you can use any kind of metal you have handy. You will need some coax and sma or rpsma depending on your receiver. You will need a receiver. You can use a module in a google set like fatshark, or you can use the one I have. It is the same one that can be found here https://www.getfpv.com/2-4ghz-a-v-receiver.html they are out of stock but this receiver can be found all over the net. you will also need CA glue for permanent assembly.
you have to print each part, but 2 pcs. of the antenna mast as it takes 2 of these to make a full antenna.
Assembly:
1) Assemble the antenna mast. take the 2 pcs. of mast, and the mast coupler, and use CA glue. Put glue on the coupler, and on the faces of the antenna and push them together. Let this dry.
2) Prep the ground plane. Take the copper board (120mm x 120mm) and drill a 10mm hole in the center. Next take the back plane backer, put the rivit through it. Then put the copper board on it and line everything up square. Mark the hole that is off set from the center. This is the hole for the coax connection. Drill at least a 3.5mm - 4mm hole. Take the rivit out for now. Optionally you can now glue the copper board into the back plane backer. Set aside and let dry.
3) Copper coil. Here is what I did. I took something that was smaller than the antenna mast, in my case, the handle on a leaf rake. I had a broken one, and I cut of the end. About 10". Drill a hole in the center of it that is slightly smaller than 1/4" as best you can. Then put a double sided lag screw, 1/4", or cut the hex head of a 1/4" lag screw. Put the lag screw into a drill and drive it into the broom handle. Drill a hole towards the base of th handle just big enough to put the wire in. Then spin the drill slowly, and using a pair of pliers, hold the copper wire tightly, but with enough slack to let it slip. and allow the coil to wrap tightly. You will need more than 10 wraps. I did at least 15. Next take the coil and turn it on the mast slowly. This will ensure a snug fit. Coil it all the way on. Make sure to leave a half a turn that you bend inward to fit into the capacitive tuning ring. Next, clip the coil 10 full turns from the beginning.
4) Optional - Gluing the swivel mount. If you want to glue the swivel mount to the ground plane backer: put CA glue on swivel mount face. Slide rivet through, and then through the ground plane backer. Line up the mount so that it is 90' vertical, and press together. Once the glue grabs, slide the rivet back out.
5) Assemble antenna: Take rivet, and put through swivel mount and ground plane backer. Slide the capacitive tuning ring and slide it over the rivet. Place some CA glue on end of rivet and push the mast on the rivet. Align the capacitive tuning ring so that it lines up with the end of the groove on the mast, so there is 1 half turn that is flat. The extra bit of copper coil needs to run in this groove to the end. Clip off excess at the end.
6) Coax: Slide coax through the small offset hole in the ground plane backer. Strip about 1/2" of the outer jacket of the coax. Peel back shielding and twist it together off the side. Then strip about 1/4" of the center hot. Solder the shielding to the ground plane copper board. Solder the hot to the end of the coil. (You should Align this when assembling.)
Your antenna is built.
7) mounting on tripod. In the back of the receiver base is a hole that should have 1/4" thread that fits a tripod mount. I couldn't get it to printer great, but you can force it in once and it will thread in easy after that. Attach your tripod mount to the base. Then attach to tripod. Using the hinge pin slide it trough the swivel mount of the antenna and base. Then use the hinge pin rivet to lock it together.
DONE.
4/05/2020 - First test: I tested this in my back yard. I didn't have a lot of room. Lots of trees, but it was a good first test. I flew about 250ft away. Not very far but I can say that there was no flicker or break up at all. Usually there is always some sort of breakup when changing directions. Nothing as long as I was out in front of it. Very clear video. I then flew toward the side of the antenna about 50 feet away from the side of the antenna. As soon as I got to almost 90' from the antenna, I almost lost all video. But once I went back a bit, video came back. So it is definitely directional. I did some quick direction changes and some rolls and the video was rock solid. I flew up about 100 feet, and came back down and the video was rock solid. So far it's working well. I will update with a more extensive range test.
Similar models
thingiverse
free
2.4ghz FPV antenna tower for longgggg range by Gnarkill1332
...oil maker tool for install and 16agw power wire for the coil. cut copper plate for grounding plane and solder upoyour connector!!
thingiverse
free
2.4GHz Antenna mount by Tripel
...a as well, this prevents wire damage due to bending.
the only post-printing work is to clean up the holes with a 1.5mm drill bit.
thingiverse
free
Strix Goblin Caddx Vista Mount by PaulWieland
... have the antenna outside the fuselage, you can drill a small hole in the top of the fuselage to pass the u.fl connector through.
thingiverse
free
dipole mount for 2.4Ghz RC antenna on 16mm tube by Sneezy3D
...to put a 2.4ghz coaxial dipole in to a good transmission location.
suits multi-copters with 16mm arm tubes like tarot and others.
thingiverse
free
Parabolic Double Biquad 2.4 GHz
...foil on the back of the parabola.use rp sma male plug female pin panel mount 4 hole solder connector on back side of
the antenna.
thingiverse
free
Coil Building Swivel by Jordanjones121395
...aking vape coils. it uses a standard skateboard bearing and a key-ring. the shallow hole in the back is to mount a c clamp to it.
thingiverse
free
Bix 3 foldable receiver antenna mount by Xerg
...slots underneath the motor.
use m3 nylon screw to put arm & adaptor together. you might want to mirror
bix3_antenna_adapt.stl
thingiverse
free
Vortex FrSky D4R-II Mount Version 2 by idnarbjm
...on 2 top has larger cylinders that you can drill out to 3mm and put antenna tubing in.
version 3 top has sideways antenna tubes
thingiverse
free
Antenna Mast Mount for Elecraft T1 Tuner by mfhepp
...e, you could either use regular rubber bands or apply liquid rubber to the surface of the mount.
enjoy, and see you on the bands!
thingiverse
free
LoRa Ground Plane Antenna 868MHz by sisam
...fine, you may add some glue to prevent losening.
tune
tune the antenna by cutting small pieces off the 10cm copper wire radiator.
Mchaos
thingiverse
free
Precision spinner thingy test toy??? by Mchaos
...precision spinner thingy test toy??? by mchaos
thingiverse
this is something i designed to test my printer...
thingiverse
free
Dino Toys 2 by Mchaos
...ht this would be a neat quick print for the kids.. so i flipped the legs so they were correct. it came out good. my son loved it.
thingiverse
free
30mm Honeycomb Fan Grill by Mchaos
...
i like the honeycomb fan grills, but i couldn't find one that ws 30mm to fit my v6 j-head hot end , so i remixed this one .
thingiverse
free
30 & 40 mm Concave honeycomb fan grill. by Mchaos
...; 40 mm concave honeycomb fan grill. by mchaos
thingiverse
i just thought this looked cool. its concave and honeycomb.. enjoy...
thingiverse
free
Igus Drylin bearing holder by Mchaos
... size not currently correct.. i am trying to find the right tightness...
i have uploaded a version 2 which is more streamlined...
thingiverse
free
Spool Roller by Mchaos
...nd are 15.5mm outside diameter.
bearings are also press fit so you don't have to print the caps if you don't want too...
thingiverse
free
Custom Bowden Carriage w/ dual LED's by Mchaos
...towards what i want because i cannot find any out there like this.
this is a work in progress.
added an adjustable sensor mount.
thingiverse
free
FPV GPS mount UBLOX MINI 8 by Mchaos
...#39;s designed so that you can lock a cover on it to keep the gps in place. similarly it has notches for a zip tie if you prefer.
thingiverse
free
Single and No fan case cover for Daltoncnc's Ramps case by Mchaos
...is, but didn't want the fet fans.
so i remixed it to have only a single fan, or no fan at all.
i also took of the ramps logo.
thingiverse
free
Geared Boweden Extruder (Flexable Filament Capable) by Mchaos
... it in.
i also put a cutout in so when the set screw is aligned with it, you can easily get a tool in to tighten it.
i like it...
4Ghz
thingiverse
free
WiFi Antenna Biquad Yagi 2 4GHz by 4Me
... mcneil electrical design.
usb wifi card in the back of the antenna.
spacers 3d printed.
pcbs manufactured on a pcb-cyklon mill.
thingiverse
free
APS throttle mount- by beetbocks75
...for use with aps remote contriol pcb and battery http://alienpowersystem.com/shop/radio-transmitters/alien-power-system-2-4ghzelectric-skateboard-remote-control/ ...
thingiverse
free
CrazyRadio - USB Dongle - Case by bishopfox
...the crazyradio 2.4ghz nrf24lu1+ usb radio dongle with antenna: https://www.amazon.com/crazyradio-pa-2-4ghzdongle-antenna/dp/b00qbp5242/ prints on makerbot replicator 2: high quality: 53 min...
thingiverse
free
Lenovo Yoga Router/Firewall by zigzagjoe
...zigzagjoe thingiverse https://docs.google.com/document/d/1_rdjw_5bxjvemaujwaoiev8gmxprbspwe7w8akjggb4/edit 2.3ghz i5 4200u (dual core, hyperthreading) 4ghz ddr3l (soldered) sandisk u100 16gb ssd hp nc365t quad...
thingiverse
free
Parametric Hyperbolic Worm Gear by Jerimon
...the default gear renders in 50 seconds on my 4ghz desktop computer. just for reference. customizer doesn't want to...
thingiverse
free
Zigbee Sniffer USB Hub Case for CC2530 and TTL Module. by tronix
...ttl modules for use with zigbee2mqtt boards available here https://www.aliexpress.com/item/cc2530-zigbee-module-uart-wireless-core-board-development-board-cc2530f256-serial-port-wireless-module-2-4ghz32767470382.html ...
thingiverse
free
AM4 bracket for Corsair AIO coolers by medo145
...found this model on reddit.https://www.reddit.com/r/amd/comments/62isdm/3d_printer_files_for_corsairs_asetek_aio_brackets/ original file is posted herehttp://www.overclock.net/t/1624139/official-ryzen-7-1800x-1700x-1700-owners-club-4ghzclub/7100#post_25971424 i downloaded the sldprt file and converted it to...
thingiverse
free
Jeti DC-16 II case for external transmitter module by Smart42
...orange rx dsmx diy modul mit einem 2s/600mah lipo verbaut.https://hobbyking.com/en_us/orangerx-dsmx-dsm2-compatible-2-4ghzdiy-transmitter-module.html angeschlossen wird das modul an die ppm out buchse...
thingiverse
free
QuadroCopter - 250 size by gdlzsilip
...controller : http://www.dx.com/p/crius-mwc-multiwii-se-v2-5-version-multi-copter-4-axis-main-flight-control-board-blue-227394#.v8poyvmltiu motors : http://www.dx.com/p/4-x2804-2280kv-cw-ccw-brushless-motor-4-15a-esc-2-pairs-of-6045-3-leaf-nylon-propeller-set-382471#.v8pqlvmltiu rc system : http://www.dx.com/p/flysky-fs-t6-2-4ghz6-ch-2-9-lcd-tx-transmitter-rx-receiver-radio-control-system-black-8-x-aa-178448#.v8pq2pmltiu firmware :...
thingiverse
free
Glotzkowsky Mini MK1 by Scorch1262
...thingiverse cx-12r:https://www.conrad.de/de/empfaengermodul-svs-nachrichtentechnik-0125001-reichweite-max-im-freifeld-1000-m-2-vdc-36-vdc-192443.html pic 16f628a:https://www.conrad.de/de/embedded-mikrocontroller-pic16f628a-ip-pdip-18-microchip-technology-8-bit-20-mhz-anzahl-io-16-165038.html motoren:https://www.amazon.de/gp/product/b00lcv4xuo/ref=oh_aui_detailpage_o06_s00?ie=utf8&psc=1 ladechips:https://www.amazon.de/gp/product/b00sr4fh4a/ref=oh_aui_detailpage_o04_s00?ie=utf8&psc=1 fahrtregerer:https://www.amazon.de/gp/product/b00k67w8mu/ref=oh_aui_detailpage_o09_s00?ie=utf8&psc=1 gewichte:https://www.amazon.de/gp/product/b00ijfxmia/ref=oh_aui_detailpage_o00_s00?ie=utf8&psc=1 kamera:https://www.amazon.de/gp/product/b00iextoma/ref=oh_aui_search_detailpage?ie=utf8&psc=1 kamerasender:http://www.ebay.de/itm/2-4ghz1ch-1-3-cmos-mini-kabellose-lochkamera-spionkamera-/230913888405?hash=item35c38a5095:g:i7eaaoswajvursuu ...
Helical
3d_export
$5
helical gear
...helical gear
3dexport
helical gear
3d_export
$5
Helical Gear
...l contact ratio which can improve vibration and noise. badly designed helical gears can be noisier than well designed spur gears.
turbosquid
$5
Helical Gear
...squid
royalty free 3d model helical gear for download as stl on turbosquid: 3d models for games, architecture, videos. (1502723)
turbosquid
$4
helical gears
...id
royalty free 3d model helical gears for download as blend on turbosquid: 3d models for games, architecture, videos. (1423917)
turbosquid
$40
Helical Stairs
...el helical stairs for download as 3ds, max, ige, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1422987)
turbosquid
$32
armchair-Helical
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
helical gear
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
helical gear
...cal gear for download as max, unitypackage, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1667275)
turbosquid
$4
Helical gear
... gear for download as sldpr, 3dm, 3ds, fbx, ige, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1530622)
3d_export
$50
HELICAL BEVEL GEAR
...lel and perpendicular. in parallel-axis helical gears the two opposite-hand gears provide quiet operation and high load capacity.
Gain
turbosquid
$15
Gaines Chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$15
Chair Oscar Gaine 3D Model
...chair oscar gaine 3d model
3dexport
chair oscar gaine 3d model mary 63706 3dexport
turbosquid
$20
Chandelier Hudson Valley Gaines 2216
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Chandelier Hudson Valley Gaines 2222
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Hudson Valley Gaines 2206 and 2202
...tp://www.hudsonvalleylighting.com/productdetails.aspx?item=2202-aob#.vodn9fmsv8e
including files: max 2010, 2013, obj.
turbosquid
$20
Chandelier Hudson Valley Gaines 2206 and 2202
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
free
Hudson Valley Gaines 2100
...tp://www.hudsonvalleylighting.com/productdetails.aspx?item=2100-aob#.votu3pmsv8e
including files: max 2010, 2013, obj.
3ddd
$1
Hudson Valley Gaines 2216
...tp://www.hudsonvalleylighting.com/productdetails.aspx?item=2216-aob#.vn5wlvmsv8e
в архиве файлы max 2010, 2013 и obj.
3ddd
$1
Hudson Valley Gaines 2222
...tp://www.hudsonvalleylighting.com/productdetails.aspx?item=2222-aob#.vnzc-_msv8e
в архиве файлы max 2011, 2014 и obj.
archive3d
free
Door 3D Model
...door 3d model archive3d door front door entrance door gain n150907 - 3d model (*.gsm+*.3ds) for interior 3d...
Antenna
archibase_planet
free
Antenna
...chibase planet
antenna aerial television antenna
antenna kathrein n090913 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Antenna
...antenna
archibase planet
satellite antenna
antenna 1 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Antenna
...antenna
archibase planet
equipment satellite antenna
antenna 2 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Antenna
...ntenna
archibase planet
satellite antenna equipment dish aerial
antenna 3 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Antenna
...antenna
archibase planet
satellite antenna dish dish aerial
antenna 4 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Antenna
...e planet
antenna dish dish aerial
antenna c-band satellite s180-g n210612 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
3d_export
$5
car antenna
...car antenna
3dexport
car antenna, antenna, car gadgets
turbosquid
$1
antenna
...rbosquid
royalty free 3d model antenna for download as blend on turbosquid: 3d models for games, architecture, videos. (1655786)
3d_export
free
Station with antenna
...station with antenna
3dexport
station with antenna
turbosquid
$5
Antenna
...id
royalty free 3d model antenna for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1381532)
Beam
archibase_planet
free
Beam
...beam
archibase planet
beam camber-beam hammer-beam
balance beam 2 - 3d model for interior 3d visualization.
design_connected
$16
Beam
...beam
designconnected
van rossum beam computer generated 3d model. designed by rossum, van.
design_connected
$11
Beam
...beam
designconnected
mdf italia beam computer generated 3d model. designed by arrivillaga, luis alberto.
turbosquid
$25
beam
...am
turbosquid
royalty free 3d model beam for download as stl on turbosquid: 3d models for games, architecture, videos. (1674400)
turbosquid
free
beam
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
ZERO, BEAM
...zero, beam
3ddd
zero
поворотная люстра zero , beam
archive3d
free
Beam 3D Model
...archive3d
beam camber-beam hammer-beam
balance beam 2 - 3d model for interior 3d visualization.
3ddd
free
Studio Beam
... navy
светильники studio beam
модели: mariner, ocean mariner, navy.
могут быть в разных цветах
3ddd
$1
Studio Beam
...grupius
производитель studio beam
модели: edison’s rocket pendant, edison’s rocket table lamp,romanov,elena pendant,grupius 1919.
design_connected
$11
I-Beam
...i-beam
designconnected
glas italia i-beam computer generated 3d model. designed by massaud, jean-marie.
High
3d_export
$15
ironman high
...ironman high
3dexport
ironman high poly
turbosquid
$49
High Heel Girl (High Poly)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$49
High Heel Girl (High Poly)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$49
High Heel Girl (High Poly)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$49
High Heel Girl (High Poly)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$49
High heel girl (High Poly)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
design_connected
$16
Cantu High
...cantu high
designconnected
linbrasil cantu high computer generated 3d model. designed by rodrigues, sergio.
design_connected
$16
Koja high
...koja high
designconnected
blå station koja high computer generated 3d model. designed by mattson, fredrik.
design_connected
$16
Ribbon High
...ribbon high
designconnected
cappellini ribbon high bar stools computer generated 3d model. designed by nendo.
design_connected
$11
Garry High
...garry high
designconnected
ligne roset garry high computer generated 3d model. designed by jourdan, eric.
2
design_connected
$11
No 2
...no 2
designconnected
sibast no 2 computer generated 3d model. designed by sibast, helge.
turbosquid
$6
Cliff Rock 2-2
...uid
royalty free 3d model cliff rock 2-2 for download as obj on turbosquid: 3d models for games, architecture, videos. (1619161)
turbosquid
$29
Book variation 2 2
...3d model book variation 2 2 for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1366868)
turbosquid
$22
Classic baluster (2) (2)
...assic baluster (2) (2) for download as max, obj, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1483789)
turbosquid
$99
Smilodon 2 Pose 2
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Barrel Barricade 2-2
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$6
Wall Trophy (2) (2)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Tire label 2 of 2
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Кровать, 2 тумбочки, 2 светильника
...кровать, 2 тумбочки, 2 светильника
3ddd
кровать, 2 тумбочки, 2 светильника
нормальное качество
формат 3ds max
без текстур
3ddd
free
Кровать, 2 тумбочки, 2 светильника
...кровать, 2 тумбочки, 2 светильника
3ddd
кровать, 2 тумбочки, 2 светильника
нормальное качество
формат 3ds max
без текстур