Thingiverse
14500 to 25500 Cell Adaptor by kitsune109
by Thingiverse
Last crawled date: 3 years ago
14500 (AA cell) to 25500 (26650 = C cell) adaptor sleeve for use in devices designed for 26650 sized cells.
Note: 14500 sized cells physically contain a fraction of the storage capacity of 26650 sized cells. AA cell alkaline are not a suitable replacement for C cell alkaline batteries. It is not recommended to use these adaptors in this capacity for anything other than testing or temporary emergency use.
Not all 14500 sized cells have the same outer diameter, typically due to differences in the plastic shrink insulation used. Dummy AA cells, 14500 LiIon cells, etc. tend to be slightly thicker than AA alkaline brands.
1400mm (14mm ID) = cells with no plastic shrink insulation
1425mm (14.25mm ID) = most AA alkaline cells
1450mm (14.5mm ID) = dummy cells and LiIon cells
1500mm (15mm ID) = IMR with adhesive branding labels
Side note: Designed for using 2xIMR/LiIon 14500 cells in devices intended to run off of 4xC cell alkaline batteries. This results in an over voltage state that can potentially damage electronics designed around the 6.6v ceiling of 4 factory fresh, quality alkaline batteries. 2x lithium cells rated at 7.4v typically peak around 8.4v on a full charge when new. Internal protective circuitry may trip upon detecting an over voltage state (device won't operate). Worst case scenario: over voltage state can burn out components rated for lower voltage.
In short: use in this capacity at your own risk.
Note: 14500 sized cells physically contain a fraction of the storage capacity of 26650 sized cells. AA cell alkaline are not a suitable replacement for C cell alkaline batteries. It is not recommended to use these adaptors in this capacity for anything other than testing or temporary emergency use.
Not all 14500 sized cells have the same outer diameter, typically due to differences in the plastic shrink insulation used. Dummy AA cells, 14500 LiIon cells, etc. tend to be slightly thicker than AA alkaline brands.
1400mm (14mm ID) = cells with no plastic shrink insulation
1425mm (14.25mm ID) = most AA alkaline cells
1450mm (14.5mm ID) = dummy cells and LiIon cells
1500mm (15mm ID) = IMR with adhesive branding labels
Side note: Designed for using 2xIMR/LiIon 14500 cells in devices intended to run off of 4xC cell alkaline batteries. This results in an over voltage state that can potentially damage electronics designed around the 6.6v ceiling of 4 factory fresh, quality alkaline batteries. 2x lithium cells rated at 7.4v typically peak around 8.4v on a full charge when new. Internal protective circuitry may trip upon detecting an over voltage state (device won't operate). Worst case scenario: over voltage state can burn out components rated for lower voltage.
In short: use in this capacity at your own risk.
Similar models
thingiverse
free
Battery adaptor AA to C by Werkman
...battery adaptor aa to c by werkman
thingiverse
aa cell adaptor to c cell
thingiverse
free
Battery Collar 14500 - C-Size by JamieDragon
...ries are a hair larger than the aa's, so they don't fit well. these collars make the outer diameter the same as a c-cell.
thingiverse
free
14500 to 18650 Battery Converter / Adapter by KikiTay
... as conductor. i also had a transparent heat-shrink plastic to protect the exposed part (not required)
http://www.kikitayblog.com
thingiverse
free
AA Dummy Battery by tromano32
...aa dummy battery by tromano32
thingiverse
this is a aa dummy battery. it is used to drop the voltage of a aa pack by 1.5v.
thingiverse
free
AA Dummy Battery by DSafePrints
...aa dummy battery by dsafeprints
thingiverse
aa battery dummy
used to convert aa cell battery power to ac.
thingiverse
free
Battery adaptor / adapteur pour batterie by capucinois
...ry adaptor (nimh alkaline).
le fichier _param.stl fait pour les deux types de batteries / the file param.stl fit for both battery
thingiverse
free
AA-C Size Battery Adapter by koryhurst
...battery adapter by koryhurst
thingiverse
just a cylinder to allow aa batteries to be used in devices that want c-size batteries.
thingiverse
free
battery dock by pvnencak
...encak
thingiverse
battery holder/stand for various battery types 18350/18500/14500/18650/26650/21700 with slots for empty cells.
thingiverse
free
Dummy C Battery by tromano32
...tromano32
thingiverse
simple dummy cell to drop voltage in a battery pack
remix of my http://www.thingiverse.com/thing:579302
thingiverse
free
AA Battery Insert Slugs by Velocitasfortis
...other slug. (not pictured as of this time)
may be possible to use large-gauge copper wire instead of nail if you have some handy.
Kitsune109
thingiverse
free
180 Motor Cover by kitsune109
... slide into a rectangular hole cut into the shell, but can simply be glued to the shell with the appropriate adhesive or solvent.
thingiverse
free
Zippo Lighter Shipping Box by kitsune109
...zippo lighters that no longer have the display case they shipped in.
cover fit is snug; use a quarter or a nickel to pop it open.
thingiverse
free
Nerf Slingstrike Replacement Sled by kitsune109
...actical, yet fun design. the catch sled is arguably the weakest link in the design, making it the part most likely to fail first.
thingiverse
free
StryfeDartGuide by kitsune109
...ion during feed and slightly tighter tolerances, as the wings wrap around the upper half of the top dart in an inserted magazine.
thingiverse
free
RaptorStrike Bolt Handle Clip by kitsune109
...s removal if the blaster needs to be disassembled.
.25 and .225 height size options, depending upon the accuracy of the printer.
thingiverse
free
Caliburn Sear (+Durability) by kitsune109
... be a break in period as the sear polishes through use. works same as the original piece once that initial polishing is complete.
thingiverse
free
Caliburn Wide Trigger Guard by kitsune109
...x the width of the stock guard, resulting in a comfortable grip that distributes pressure over a wider area of the middle finger.
thingiverse
free
Nerf Rival Kronos 6 Shot Magazine Follower by kitsune109
... factory magazine follower that allows an additional hir ball to be loaded (6 shots).
complements 6 round stripper clip systems.
thingiverse
free
Caliburn Bull Ram by kitsune109
...h no loosening of the priming arm screws or significant damage to the ram. dry firing will not significantly damage the bull ram.
thingiverse
free
Caliburn Shock Buffer by kitsune109
...but when printed direct on glass, the mirror finish tpu side naturally adheres to a mirror finish ram face without any adhesives.
14500
thingiverse
free
14500 flashlight adapter by MrJWebb
...14500 flashlight adapter by mrjwebb
thingiverse
use a 14500 li-ion battery in a harbor freight flashlight
thingiverse
free
14500 to 18500 Battery Adapter
... find.
print came out really great without supports, but i recommend to add 6+ lines brim if your bed adhesion isn't perfect.
thingiverse
free
14500 16500 li-ion adapter by textual_healing
...into a 16500 holder. i made this initially to put my excess 14500 (lightsaber size) cells into my taranis x-lite radio controller
thingiverse
free
14500 to 18650 Battery Converter / Adapter by KikiTay
... as conductor. i also had a transparent heat-shrink plastic to protect the exposed part (not required)
http://www.kikitayblog.com
thingiverse
free
Battery Collar 14500 - C-Size by JamieDragon
...ries are a hair larger than the aa's, so they don't fit well. these collars make the outer diameter the same as a c-cell.
thingiverse
free
14500 battery holder by beamzer
...ttery holder by beamzer
thingiverse
just a simple battery holder for your projects. design is done in openscad so easy to modify
thingiverse
free
14500 Battery holder by bbrown1951
...nting this. to make the contacts a person will need to use 1/4" wide brass strips. these will have to be bent to fit snugly.
thingiverse
free
14500 Battery Adapter for 3x AAA Flashlight Torch Pack by jmbneaf
...mple remix of mrjwebb's 14500 flashlight adapter to print faster as two parts that use less material.
designed with fusion360
thingiverse
free
14500 Flashlight Battery Holder by wrk24wheel
...oling and prevent the battery from overheating which could be done with a solid design.
dimensions are: 1.5"l x .88"w
thingiverse
free
Flashlight 14500 and 18650 Battery Stand by Hackbert
... battery stand by hackbert
thingiverse
simple flashlight stand for 2x ultrafire cree with battery (2x14500 and 4x18650) storage.
Adaptor
thingiverse
free
DH1 Adaptor
...dh1 adaptor
thingiverse
dh1 adaptor
thingiverse
free
Moses Adaptor
...moses adaptor
thingiverse
test adaptor for moses foil
thingiverse
free
MBB adaptor by Peter161
...mbb adaptor by peter161
thingiverse
it an adaptor to an worktool for mobil beat-beting
thingiverse
free
Tripod Adaptor by cmot17
...tripod adaptor by cmot17
thingiverse
an adaptor to put my webcam on a tripod.
thingiverse
free
tracer adaptor by renegead
...tracer adaptor by renegead
thingiverse
a tracer adaptor for 8 inch dan wesson revolver .
thingiverse
free
Shifter Adaptor by kebekwa
...shifter adaptor by kebekwa
thingiverse
jdm shifter adaptor with a 1.5 pitch to fit my s13 180sx
thingiverse
free
Valve adaptor by Daniel_Snowsurf
...o inflatable toy 5-9 mm inner diameter. for quick release schrader valve pump, not threaded.
designed in fusion 360 valve adaptor
thingiverse
free
Honeywell Evohome Adaptor
...honeywell evohome adaptor
thingiverse
adaptor for evohome thr92 thermostat to my valves. its a m28x1.0mm to m30x1.5mm adapter.
thingiverse
free
PET Adaptor by evilthingsmaker
...pet adaptor by evilthingsmaker
thingiverse
pet adaptor
print at 103% scaling in print program
this seems to be due to overlap
thingiverse
free
Bandsaw Vacuum Adaptors
...bandsaw vacuum adaptors
thingiverse
i have a grizzly bandsaw and i design few custom vacuum adaptors for it.
Cell
thingiverse
free
Cells by rfeitlinger
...cells by rfeitlinger
thingiverse
four of my student's best 3d cell models.
2 plant cells and 2 animal cells
thingiverse
free
Cell by wldl5
...cell by wldl5
thingiverse
a cell i made for a school project.
thingiverse
free
Cell Dish by stuartfingerhut
...cell dish by stuartfingerhut
thingiverse
cell dishes were are inspired by the shape of cells in leaves.
thingiverse
free
Plant Cell
...ant cell
thingiverse
this is a model of a basic plant cell. it can be printed in colour as it is coloured or painted afterwards.
thingiverse
free
plant cell
...plant cell
thingiverse
this is a plant cell that i made for scientific research, it is very cool to print on software
thingiverse
free
Cell Thing by twwoodward
...cell thing by twwoodward
thingiverse
cell file
thingiverse
free
Splinter cell by speedtwin69
...splinter cell by speedtwin69
thingiverse
splinter cell
thingiverse
free
K CELL by shastasheen
...k cell by shastasheen
thingiverse
k cell
thingiverse
free
FCC cell - primitive cell repetition 5 times
...fcc cell - primitive cell repetition 5 times
thingiverse
fcc crystal plotted by 5 repetitions of the primitive cell
thingiverse
free
Cell Holder by janemiceli
...cell holder by janemiceli
thingiverse
cell phone holder