1 X 1 Laptop by JackB106

...--------------------------------------------------1----------1----------------1-----------------------1--------------------------

...ces http://mathworld.wolfram.com/egyptianfraction.html http://www.maths.surrey.ac.uk/hosted-sites/r.knott/fractions/egyptian.html

...magic token +1/+1 & -1/-1 by kilgara2b thingiverse a magic the gathering token +1/+1 and -1/-1

...tudiosgaming thingiverse if you are in need of the 4pstudiosgaming +1/+1 and -1/-1 counters, then you came to the right page :-p

... 1/6, 1/8, 1/10, and 1/12 sized wedges as well as a circular base for them to fit onto. there are no labels on any of the pieces.

...ages above, you will see two 1 1/4" od hoses attached together, and a 1 1/4" od hose attached to a 1 1/2" id hose.

... counter mtg by rekadefender thingiverse this is a 1/1 zombie counter for any spells or special abilities that cast a 1/1 zombie

...etrkk thingiverse fitting pipe thread 1" to 1 1/2" inner thread 1" outer thread 1 1/2" one with wrench base.

...dapter for syphon - 1 1/4" to 1 1/2" h10,5mm the project was realized with tolerances for printing with abs + tape ptf.

...d adapter 1" to 1" 1/4 by printerforever thingiverse this is an adapter 1" to 1" 1/4 (male to male) enjoy !

... a model of a specific laptop) by thegaminguy21 thingiverse this is a model of laptop and is not modeled from a specific laptop.

...laptop stand for larger laptops by mrspiffy thingiverse laptop stand for larger laptops. about 10 degree slope.

... the slot for the laptop set at 40mm. it will fit any laptop under this thickness but your laptop will lean one way or the other.

...laptop holder thingiverse laptop

...laptop by danielesko30 thingiverse this is a laptop

...laptop by leonk thingiverse laptop

...laptop by anurag thingiverse laptop

...laptop holder thingiverse laptop holder

...laptop stand thingiverse laptop stand

...laptop stand thingiverse laptop stand

...magic token +1/+1 & -1/-1 by kilgara2b thingiverse a magic the gathering token +1/+1 and -1/-1

...tudiosgaming thingiverse if you are in need of the 4pstudiosgaming +1/+1 and -1/-1 counters, then you came to the right page :-p

... 1/6, 1/8, 1/10, and 1/12 sized wedges as well as a circular base for them to fit onto. there are no labels on any of the pieces.

...dapter for syphon - 1 1/4" to 1 1/2" h10,5mm the project was realized with tolerances for printing with abs + tape ptf.

...l fit both 1 1/8" and 1 1/5" bearing cups. i used a 3/8ths" threaded rod with nuts and thick washers on each end.

...design cheeseborough clamp for hanging lightfixtures and other items onto 1-1/4"-1-1/2" npt pipe. use at your own risk.

...them instead of money coin in your supermarket cart or in your swimming pool locker. edit : updated 1£ coin with new dimensions

...d adapter 1" to 1" 1/4 by printerforever thingiverse this is an adapter 1" to 1" 1/4 (male to male) enjoy !

...playstation 2, 1:1 by vitting thingiverse made a 1:1 playstation 2.

...re thinner and actually fit within each other to show equivalent fractions. also, check out the same version with braille (here).