thingiverse

free

Makergear Z Axis Knob by Aydelott

...makergear z axis knob by aydelott thingiverse makergear z axis knob press in steel when the abs is still a little warm

thingiverse

free

7mm Wrench for Makergear M2 Z adjustment by tomlombardi

...mlombardi thingiverse this is a 7mm deep socket wrench i designed to make adjusting the z homing screw on a makergear m2 easier.

thingiverse

free

Makergear M2 Z-Stop Wrench by neep33

...top. it works, but is still hard to use due to very minimal space around that nut. any suggestions for improvements are welcome.

thingiverse

free

MakerGear M2 Z axis gear knob by jhollin9

...se new design for makergear m2 z axis knob. the original collar with set screw can be press fit in just like the original knob.

thingiverse

free

Z-Axis knob for the MakerGear M2 3D printer by Karl_Williams

...illiams thingiverse an alternative z-axis knob for the makergear m2 3d printer. print the knob and then press fit a 5/16 collar.

thingiverse

free

Z Rod Stabilizer for Makergear Prusa Mendel by Pacca

...rusa-mendel attention: the distance between the smooth rod and the threaded rod is not the one of a standard lm8uu prusa mendel!

thingiverse

free

Z Knob Adapter for MakerGear M2 by Mymoliso

...2. it simply sits on top and allows for faster and easier manual movement of z positioning the bed. i made mine out of black pla.

thingiverse

free

Makergear M2 Z axis hard end stop by tomlombardi

...e commanded to push into the switch and mess up the z adjustment, this thing clips on to the z axis guide rod and acts as a stop.

thingiverse

free

Z rod stabilizer for Makergear Prusa Mendel rock solid by mic

...olid by mic thingiverse z rod stabilizer for makergear prusa mendel rock solid i increased the support section for ball bearing

thingiverse

free

Makergear M2 Z axis stay by tomlombardi

...giverse this thing loosely slips over the z axis knob on an m2 to hold the platform up while the stepper motors are powered off.

thingiverse

free

MakerGear M2 Tool Holder (z-axis screw driver support) by dryeti

...dprinterhowto additionally hosts the tools from the model "makergear m2 z-axis screw driver and counter nut tightener".

thingiverse

free

Ratcheting Z Axis Stay for Makergear M2 by MagicEngineer

...ngineer thingiverse for when you need to hold the z axis knob at a precise position, this stay allows for 10 degree adjustments.

thingiverse

free

MakerGear M2 Z Axis Spring Stop by MakerJay

... thingiverse this stop keeps the z axis from coming to a hard stop. print at 30% infill with 15% support between spring levels.

thingiverse

free

MakerGear M2 z-axis bolt screw driver and counter nut tightener by dryeti

...ts the z-axis bolt driver plus counter nut tightener. look for "makergear m2 tool holder (z-axis screw driver support)"

thingiverse

free

MakerBot Z Pulleys by MakerGear

... currently being printed separately but will be combined once any kinks have been worked out. makerbot made (using 0.4mm nozzle).

thingiverse

free

Z-knob stop for MakerGear M2 by TimEdwards

...o the left. see http://www.thingiverse.com/thing:934680 for another version that solves the extruder assembly clearance problem.

thingiverse

free

MakerGear M2 z-axis knob bracket by wschleter

...off. the bracket fits around the octagonal knob. be sure to remove the knob before operating the motor !!! you have been warned.

thingiverse

free

Makergear M2 Z-screw reinforcement by rsheldiii

...ng against the right z axis bearing trap. i uploaded the scad because i thought it was funny. it does work pretty well though

thingiverse

free

Makergear M2 z stage motor cooling duct by enoworx

...stage motor cooling duct by enoworx thingiverse duct is fitted with a standard 40mm fan. 10mm mounting screws (top) can be used.

thingiverse

free

MakerGear M2 Z-Stop Extension For E3D Hotend by Neo_Usagi

...s endstop. i found that the printrbot z endstop extension worked nicely but was too short. i extended the length of the assembly.

thingiverse

free

Z knob stay for rsilvers' MakerGear M2 knob by jsc

...rsilvers' remix of karl william's m2 z knob, but i missed being able to use tomlombardi's z axis stay. so i made one.

thingiverse

free

Makergear M2 Z axis stop / holder by rswen

...t's strong and prints quickly and easily. stl file only. clean file, ready to print, no netfabb errors. no supports needed.

thingiverse

free

MakerGear M2 Z Adjustment Wrench by profhankd

...ou can spin the screw to the desired height with your fingers -- then use the wrench to lock it again. really quick z adjustment!

thingiverse

free

Z-knob stop for MakerGear M2 dual by TimEdwards

...op the lever from twisting in the locked position, and also helps keep the level from slipping out when using it as a hand crank.

thingiverse

free

MakerGear M2 Z-axis Stay by dave21740

...tor isn't powered, but the one at work drops like a stone, so i cobbled this together to use when i want the bed to stay put.

thingiverse

free

MakerGear Z-knob with Crank and Stop by Corey

...g:934680 i recommend printing the crank in a color other than black so that you don't keep misplacing it like i do with mine.

thingiverse

free

makergear m2 z axis knob and matching lock by Mrcleanr6

... the knob. you can raise the bed where you want and drop the lock on the knob to hold it in place while you work on your machine.

thingiverse

free

Optical Z Sensor for MakerGear M2 by WarlockD

...unt so i just made this quickly. i forgot to add a 0.1 to the screw holes so they just fit a m3, so you might not need the nuts.

thingiverse

free

Yet Another Z Endstop Adjuster Prusa, RepRap, MakerGear by FiatSlug

...ne adjustments are made by turning the adjustment screw. this eliminates the need to tweak the z offset in your slicer software.

thingiverse

free

Cupcake Z Timing Pulley (really, a cupcake!) by MakerGear

...les need some work so i'll upload those later... nice cupcake accoutrement for a cupcake??? printed by a cupcake too!! enjoy!

thingiverse

free

MakerGear M2 Enhanced Z-Axis Knob by rsilvers

...ged "m2" engraving to an arrow pointer to better show orientation. added fillets and chamfers for looks and strength.

thingiverse

free

MakerGear M2 Z-axis Home Switch spacer to prevent drift of Z-home by Corey

...with the v3b extruder. the newer v4 equipped printers have a new home switch design which solves this problem in a similar way.

thingiverse

free

MAKERGEAR M2 Z-AXIS BRAKE by slipshine

... to go in the cross hole on the handle to keep it from spinning off. (it is better to tap the hole before putting the screw in.)

thingiverse

free

MakerGear M2 moving Z Endstop to the Bottom and OctoPrint by arnoldpro

...latform -diff shows your z changes. the difference between old and diff gives the new offset. attention: 2.78 minus -0.05 = 2.83!

thingiverse

free

Makergear M2 Z-Axis Knob Rev. E by Wythkyn

...: http://www.thingiverse.com/thing:1131435 i printed it on fast setting as the shape is pretty basic, nothing special. have fun!

thingiverse

free

Z-Stop for Makergear M2 by Neo_Usagi

...ween not sticking or sticking too hard. its that sensitive. but if you get it to work, its the best surface i've used so far.

thingiverse

free

MakerGear M2 Z Axis Knob - Spiral by MiseryBot

...n the zip. you can mess with the open scad source in the attached zip, or just import the huge stl from the zip into your slicer.

thingiverse

free

A better Makergear M2 Z axis stop / stay by loiphin

...flip it over and use it as a winding handle. but dont leave it on when printing, as it will interfere if the extruder gets close.

thingiverse

free

makergear m2 bed lvl and z height calibration by Mrcleanr6

...ou'll need to get it close before hand. another note is i have the layers set at .15 and temps are set more for abs. enjoy!!!

thingiverse

free

Z Rod Stabilizer - Small by JulioRadesca

...fits a 608z bearing. it is exactly like the makergear z rod stabilizer - http://www.thingiverse.com/thing:23192 - but without the...

thingiverse

free

50mm blower mounting system - Makergear M2 Z-axis cooler by robertwallace

...s the fan pulls warm air out of the control box it's mounted beside, helping to keep the drive electronics a tiny bit cooler.

thingiverse

free

Z Rod Stabilizer - 2 Smooth Rod Connections by JulioRadesca

...fits a 608z bearing. it is exactly like the makergear z rod stabilizer - thingiverse.com/thing:23192 - but with 2...

thingiverse

free

Yet Another MakerGear Tool Holder for the M2 by juliezva

...-stop bolt adjustment, so that peg is removed in the modified tool holder linked below.) http://www.thingiverse.com/thing:1516995

thingiverse

free

Loches Z Axis Upgrade for MakerGear Prusa Mendel by Lochemage

...eep the carriage from binding. i've found that this modification works well and causes no noticable change in print quality.

thingiverse

free

Z Axis Return Spring by Breylon

...z axis from dropping onto the motor of my makergear m2. an added advantage, theoretically, is that the placement...

thingiverse

free

M4 Hex Nut Thumbscrew for Makergear M2 by Karl_Williams

...hex nut with the thumbscrew to make setting the z height...

thingiverse

free

Mosaic Z endstop support. by alexanderhiam

...alexanderhiam thingiverse after about two months of owning a makergear mosaic, i had only one small issue. the guide...

thingiverse

free

MakerGear M2 Rev.E Toolholder by juliezva

...wrench was. all else is the same....it still has a slot for your tweezers, a calipers, the screwdriver and the five hex wrenches.

thingiverse

free

Cupcake "M" Jar by WRIGHTMEDIA

...is inspired by the makerbot logo and makergear's cupcake z timing pulley...

thingiverse

free

Prusa Z Rod Constraint by ScribbleJ

...thingiverse inspired by the z rod constraints on the makergear prusa. you can print 2 or 4 of these...

thingiverse

free

MakerGear M2 18mm Inductive Prob Bracket for Auto Level by SCHMENKE

...is directly from the makergear github repository at [https://github.com/makergear/m2/tree/master/experimental parts/z probe for auto-level], i have included it here for...

thingiverse

free

Makergear M2 Tool and Tape Holder by sthone

...drive allen, and tweezers. it will also hold the zstop, and a roll of 3" blue painters tape. it...

thingiverse

free

50mm case fan funnel by designrama

...explanatory. i made it for cool off makergear m2's z step motor. connect fan's power to ramb0 extruder 1's...

thingiverse

free

Wobbless X Mounts for MakerGear Prusa by odudex

...lunar rover wheels. the structure uses abs flexibility as absorber.http://youtu.be/xavhz0x4dm ...

thingiverse

free

Z-Axis-Stepper Fan-Duct by uli

...by uli thingiverse this is a fanduct for a makergear m2 z-axis stepper motor. the stepper was getting very...

thingiverse

free

MakerGear M2 Filament RunOut Switch bracket by SCHMENKE

...bracket for the makergear m2. i used the old z endstop micro-switch and led from the m2, as i...

thingiverse

free

Makergear M2 Enclosure for Rambo board and Viki LCD by whoDat

...the lcd while still allowing full travel of the z axis. there is also a slot on the left...

thingiverse

free

MakerGear Simplified Extruder Block with Quick Release and Rear Motor Mount by Lochemage

...bigger on-going project i'm working on to increase the z axis limits, which can be found here http://www.thingiverse.com/thing:22887. if...

thingiverse

free

M2 Electronic Enclosure Hatch Latch by tomlombardi

...to help with clearance issues between the box and z ...

thingiverse

free

Makergear M2 Maintenance Lighting Control Box by RepliKa

...the lighting provides illumination for cleaning and lubricating the zaxis mechanism and guides as well as during z-axis stop...

thingiverse

free

makergear m2 bed corner bumper by Mrcleanr6

...need to do is just scale it in the z axis to thin it down a little or you...

thingiverse

free

Timer pulley by Zaggo

...enough and the timer belt slips too easy. when makergear published their z pulleys ( http://www.thingiverse.com/thing:1081 ) i asked...

thingiverse

free

Threaded Rod to Lead Screw Adapter - Made for MakerGear Prusa Mendel may work for others by SiRkIt

...x3/8in pan head screws. i now have much smoother z axis motion and i didn't have to remove more...

thingiverse

free

Ridiculously Simple Z-axis Micro-Adjuster by Georgewchilds

...micro-adjuster by georgewchilds thingiverse this is an adaptation of makergear#39;s concept for micro-adjusting the z-axis height for a prusa...

thingiverse

free

iphone camera mount for Makergear M2 - Lockable ball & socket by SCHMENKE

...iphone 5s, however you can easily adjust the phone siz in the "phonemount.scad" file (the variables are at the...

thingiverse

free

Short Printable Extruder Holder for Brutstruder on MakerBot by bld

...longer reached my build platform after i installed twotimes' zrider http://www.thingiverse.com/thing:4740 and x-y lowrider...

thingiverse

free

MakerGear M2 bed support spring by TimEdwards

...this curiously shaped device prevents hard drops of the z stage on the makergear m2 when the motors are...

thingiverse

free

1.75mm Filament Drive - Makergear M2 Tapir Shroud by designrama

...clear the binder clips. just make sure you lower z stopper by 2mm as well. print it with...

thingiverse

free

Makergear M3 Cooler to M2 Conversion by sthone

...may (or may not) hit the older style octagon z knobs when the head is parked. (i no longer...

thingiverse

free

Makergear M2 Optical Endstop Mount by Easybotics

...various makergear m2 mods:https://youtu.be/jd6ztccd0j8 by - http://www.easybotics.com/ and - http://hilo90mhzcom/ ...

thingiverse

free

Around-the-nozzle cooling ring by scanlime

...use iwo's design, but i just upgraded to a makergear stepper plastruder on my thing-o-matic, and there wasn't enough...

thingiverse

free

Prusa MK3 hard foot by daveadam

....sat and .123x files so they'd be easy to customiz refine. printed on makergear m2e but installed on prusa...

thingiverse

free

MakerGear M2 Filiment Guide with BLTouch Auto Bed Leveling Bracket by flyingpole

...switch between them at will without re calibrating my z stops, etc. hope that this helps you out. of...

thingiverse

free

Makergear M2 Dial Indicator Mount by designrama

...from printer interface. i use a z axis stay http://tinyurl.com/nzwkc3 to lock the bed in...

thingiverse

free

3mm Extruder for Makergear M2 by Xezerk

.... you will need to re-determine your z-offset since the new head is likely to be at a slightly different height than the old one.

thingiverse

free

Wobbless X mounts 1.0 by odudex

...v2 parts and makergear, for both bushing and lm8uu z guides. solidworks files:https://grabcad.com/library/wobbless-x-mounts-1 update jan 2016: bushed_8mm_no_bending_pro_screw.stl is part...

thingiverse

free

MakerGear M2 rear cable harness guide by TimEdwards

...they are not in the way of either the zstage assembly or filament spools on the right side. and...

thingiverse

free

makergear m2 fan bracket by Mrcleanr6

...over slightly so it does not hit the m2 z axis frame. its beefier around the hex nut area...

thingiverse

free

MakerGear M2 Tool Holder for modified spool holder by SandiaSlice

...sized to act as a snug seat for this zknob stay: http://www.thingiverse.com/thing:267185 the picture with the tools shows all...

thingiverse

free

Mendelmin 1.0 by ziggurat

...for someone still using a prusa i2 with a makergear plastruder, who has access to a laser cutter. this...

thingiverse

free

Simple Clip-On Fan Mount by MrJohn

...where the x axis is or right above the z lead screw as seen in the photos. the only...

thingiverse

free

Makergear M2 Cricut Cutting Blade Attachment by sthone

...it works great. it's a little tricky getting the zheight correct so it just cuts through the vinyl and...

thingiverse

free

Modified M2 Easy Access Drive with Leveling Attachment by stephanfr

...on amazon) for bed leveling. also included is a z axis spacer that keeps the stage a centimeter from...

thingiverse

free

Loches Dual Bowden 1.75 by Lochemage

...slow retraction of 10mm to remove the blobbing and nozle ...

thingiverse

free

Makergear M2 Drawing Attachment (The Scribbler) by sthone

...use the markers i move (slide up) my entire zstop bracket and switch to keep the hotend away from...

thingiverse

free

Makergear M2 Dial Indicator Mount by Cre8tor10

...the: türlen dial indicator 0-1" agd spec 0.001" w/lug backhttp://www.amazn.com/t%c3%9crlen-dial-indicator-spec-0-001/dp/b0043f779k ...

thingiverse

free

Part Cabinet - different drawer options by dellrio

...of dans original cabinet, i found i needed more z height in some of my drawers. i have added...

thingiverse

free

MiseryPusher: Geared Stepper filament pusher for MK5 extruder by MiseryBot

...stepstruder nema 23 direct drive pivoting filament pusher by jstkatzttp://www.thingiverse.com/thing:7037 yet another extruder filament pusher by jaghttp://www.thingiverse.com/thing:7113 accessible wade's...

thingiverse

free

Yet Another RepRap Style Printer by mblaster

...x 200mm offered by the reprap heated bed. the z direction also extends 200mm-ish (i have to get the...

thingiverse

free

Anet A6 - Autolevel bed sensor Blue SN-04N by d3adlydozen

...default_kp 22.2 //#define default_ki 1.08 //#define default_kd 114 // makergear //#define default_kp 7.0 //#define default_ki 0.1 //#define default_kd 12...

thingiverse

free

Makergear M2 Larger Electronics Box with 2 LM2596 Holders by dellrio

...event i choose to upgrade to dual extruder. my z motor never even gets...

grabcad

free

MakerGear M2 Z-Axis Caps

... get whatever offset you need. the skirt drops over the locknut on the stop bolt for stability when it contacts the microswitch.