36 bit lure 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Heavy hitter skirted lure by owendare
...heads, printed lures are light and require a fair bit of cupping to stop them just skimming the surface....
thingiverse
free
Lure module Pokemon GO by Steamtowers
...a piece of acrylic and electronic components with small bit of acrylic rod for the stacks to light up...
thingiverse
free
Swimbait Fishing Lure REMIX by Mindor1982
...remix from jakejake thx. https://www.thingiverse.com/thing:941408 it is a little bit easier to print and strong. https://www.youtube.com/watch?v=n7gjqhb75d0...
thingiverse
free
Jointless Rattling Lure by bigmac0636
...make my own changes. i made it a tad bit smaller, made it joint-less, and added a hollow portion...
thingiverse
free
mold for silicone frog/rat lure by 1337gallagher
...the crevices making sure to overfill it just a bit and squeeze the mold together. clamp or rubber band...
thingiverse
free
The Twerkbait lure
...belly hook hanger, pop a swivel or a bent bit of wire, then slip the long through wire in...
thingiverse
free
LotP - Sorceress sister (minor Heroine) by Massenzio
...is a first try of, cause i have a bit of trouble in the female blender body :d) there...
thingiverse
free
Jaye-Plug by kingscharter
...you're all set, ready to fish. action is every bit as good as the...
thingiverse
free
Fishing lure #3 with gills and larger body by sirmakesalot
...i printed at 100% so it would be a bit heavier but if you change the infill you change...
thingiverse
free
Rattle Trap Fishing Lure by sthone
...ultralight pole so far and it was a tad bit erratic. i think it might need a little more...
thingiverse
free
55 mm Minnow lure for trout fishing (stencils included)
...= 3.2 g hard sinking: 100% infill. a little bit more difficult to made. it is necessary to cut...
thingiverse
free
Popper Licious - Lure - Fishing Lure by arovillard
...bite into. i personally drill the holes with a bit half the diameter of the eye screw and then...
thingiverse
free
The Cranky Lure by RenMauPer
...thickness being 1 mm (the details come out a bit sharper then). there's a cavity in the belly that...
thingiverse
free
Flat Side CrankBait Lure by sthone
...the skinny one works great although it required a bit of tuning to get it to swim straight but...
thingiverse
free
tiny crankbait. by rallekralle11
...start spinning out of control. i may tinker a bit with the balance to see if i can fix...
thingiverse
free
Fully Printable Fishing Rod by CaseyJohnson
...the suggestion of predator04. you can fit quite a bit of stuff in there! update 6/25/15: i added a...
thingiverse
free
Inshore Saltwater Fishing Lure by lanepulcini
...you may have to cut off a a tiny bit of the bottom layer to get it flat. because...
thingiverse
free
Soft Plastic Lure Mold by PatrickSalvador
...surface to get the body to wobble. retrieve a bit faster on the surface and get the tail to...
thingiverse
free
Lotp-new-infantry-test
...be smaller and in group, heroes will be a bit bigger and single in hex. this is a test,...
thingiverse
free
The Mewthree lure master (re-upload) by RenMauPer
...going to need to scale the model down a bit. there are also variants with the tail curve going...
thingiverse
free
UL Lipless Crankbait #15
...and glue them together. then use a 0.8mm drill bit to clean the holes and install the hook hangers...
thingiverse
free
Fishing Leader Twister by moipopples
...printing if holes are too small use a drill bit to enlarge them. i have tested with 0.8mm iron...
thingiverse
free
texas popper revisited by megic
...this nice lure. i wanted to improve it a bit (from my point of view) and i fixed a...
thingiverse
free
altoids fishing kit "catfisher" by Cadfinger
...to design another little fishing reel that is a bit more practical than my first one http://www.thingiverse.com/thing:2002148. as the...
thingiverse
free
Squid lure full body by valand70
...something from here you will support me a little bit to make these projects. 1kg pla filament - ebay1kg...
thingiverse
free
Squid lure by valand70
...something from here you will support me a little bit to make these projects. 1kg pla filament - ebay1kg...
thingiverse
free
Minnow Trap by sthone
...the funnel was placed in the sun for a bit and then rolled to shape and held together with...
thingiverse
free
Floppy fish by chaszd
...a hole between the eyes the fish dive a bit deeper and wiggle more before going back up. added...
thingiverse
free
Bob, should we go fishing ?
...clarity. as soon as i finalize all of these bit i will be sure to add them onto post....
thingiverse
free
Lure of the Prophets (a boardgame) W.I.P. by Massenzio
...have 2 ammo slot, i need to remold a bit the arrow-pin cause i would prefer to make it...
cults
free
Rattle Trap Fishing Lure
...ultralight pole so far and it was a tad bit erratic. i think it might need a little more...
cg_trader
$4
Vibrotail Soft Lure for fishing 105mm 3D printable model | 3D
...pike perch fishing lures sportfish soft printable re pare bit vibrotail best lires hobby diy hobby diy...
cults
free
Flat Side CrankBait Lure
...the skinny one works great although it required a bit of tuning to get it to swim straight but...
cults
free
altoids fishing kit "catfisher"
...to design another little fishing reel that is a bit more practical than my first one. as the name...
cg_trader
$17
Mermaid 02 | 3D
...to all those aboard. and who doesn’t need a bit of luck when sailing the high...
3dwarehouse
free
Dao Stryver- Star Cabal Agent
...i 'adopted' her as an oc. love her to bit. ...