31 ztander 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Redbird Keychain by ztander
...erse
the version printed in the picture was sliced in half instead of printing the full z height. overall height is about 2 mm.
thingiverse
free
Dice with Square Holes by ztander
...with square holes by ztander
thingiverse
it's the same as the other 19mm dice i made but reworked with square holes instead.
thingiverse
free
Redbird Snowflake Ornament by ztander
...lake ornament by ztander
thingiverse
here's a redbird snowflake ornament that was derived using the model from my key chain.
thingiverse
free
Z coupling by ztander
...for alignment and rigidity. i had to file off part of the bolt on both ends since i had a close fit, but overall it works great.
thingiverse
free
Oiler by ztander
... http://www.thingiverse.com/thing:374368
i cut up a simple sponge and added some canola oil. this is used for pla heated at 196.
thingiverse
free
Pepe Lithophane by ztander
...cks/lithophane/ generator to make the imagine into a lithophane then sliced a few layers off the bottom so you can see it better.
thingiverse
free
Mill Safety Cover by ztander
... only put the milling machine in high range. this was created to stop students from accidentally putting the machine in reverse.
thingiverse
free
Custom USB holder by ztander
... holder has a press fit to a .3 inch thick table. fits nicely. i had to make again after i realized it needed support material.
thingiverse
free
Sunglasses Repair by ztander
... bond the parts together. tape was used to match the other side of the glasses.
print time: about an hour
layer height: 0.2 mm
thingiverse
free
Standard 19mm dice (die) by ztander
...th holes that go through about 80 percent of the body. it gives a unique hollow look to the inside. this was made using nx 9.0.
thingiverse
free
Buegel Stoel Chair by ztander
...r change in the green was due to certain properties that had to be modified during the printing process to assure better quality.
thingiverse
free
Metric Allen Wrench Holder by ztander
...und the garage and decided to make a set.
fits for the following sizes:
10, 8, 7, 6
5, 4, 3, 2.5, 2, 1.5
layer height: 0.2 mm
thingiverse
free
Mini Car Battery by ztander
...batteries. i used 1/2 inch screws that go into the plastic easily and did a manual color change over half way through the print.
thingiverse
free
Mill Safety Cover by ztander
...by turning the spindle in the wrong direction. this gives an easy guide to show you which way the machine needs to be turned on.
thingiverse
free
Xbox One Kinect Stand by ztander
...astic. dimensions are shown in the picture (units are inches)
print time: 5 hours
print speed: 50 mm/sec
layer height: 0.2 mm
thingiverse
free
Tool Holder for 30 mm Extrusion by ztander
...helps a lot. this was printed using a 0.3 mm nozzle. support has been created in the model to accommodate the extrusion insert.
thingiverse
free
Wall Organizer by ztander
...me smaller).
print speed 50 mm/s
perimeter extrusion width: 200%
external perimeter extrusion width: 250%
number of perimeters: 2
thingiverse
free
Flexible TPU Bracelet by ztander
...u red and gray.
the grey bracelet was printed with one no top layer so the honeycomb infill would show for the first top layer.
thingiverse
free
Phone Dock for Galaxy Avant by ztander
...
-makergeeks nuclear green pla
-nozzle size 0.2 mm
-layer height 0.15 mm
-fill: 10 %
-print time: 6 hours (i know it's long)
thingiverse
free
Vise Handle Holder by ztander
...s the handle quite well.
printed with a 0.3 mm nozzle at a 0.15mm layer height. ultimachine black pla extruded at 200 degrees.
thingiverse
free
Small Metric Allen Wrench Holder by ztander
...ed with a 0.2 mm nozzle
-layer height: 0.15 mm
-print time: 1.5 hours
-hatchbox red translucent pla
-sizing: 5, 4, 3, 2.5, 2, 1.5
thingiverse
free
Assorted Filament Clips (1.75 mm) by ztander
...x clip: shown on red filament spool
maker geeks clip: shown on green filament spool
ultimaker clip: shown on black filament spool
thingiverse
free
(Obsolete) Secondary Cooling Duct for FlexMendel by ztander
...
update 9/30/2015: the vent has a thicker shell to prevent deforming. a few smaller changes have been added to improve the fit.
thingiverse
free
Kegerator Tap Handle by ztander
...andle with any beer.
here is the link for the 3/8-16 nut i used: http://m.acehardware.com//product/index.jsp?productid=30652556
thingiverse
free
FlexMendel Cooling Duct (Newest) by ztander
...ire vent off without having to take the fan off. i highly recommend printing this part in abs since it is close to the extruder.
thingiverse
free
Controller Box for RAMPS by ztander
...ented view. if you would like to have the top plate printed so the shiny side is upwards on the top of the box use this version.
thingiverse
free
40mm Cooling Duct for Flexmendel by ztander
...pstick-stepper-ultra-quiet/dp/b01gjfvfc6/ref=sr_1_1?s=industrial&ie=utf8&qid=1492877645&sr=1-1&keywords=tmc+2100)
thingiverse
free
(obsolete) Cooling Duct for FlexMendel by ztander
...r. also there is a wider area towards to center so there is more flow directed at the nozzle tip. (clear version is the newest)
thingiverse
free
Business Card Design by ztander
...at fill just right)
update 9/16/2015: i have added a qr code which links to my 3d hubs webpage. first picture is the new card.
thingiverse
free
Mighty Stand - Customizable Heights by ztander
... loosely you can put your monitor at risk. i also used a microfiber cloth between the stand and monitor base to prevent slipping.
thingiverse
free
Mighty Stand - Width Expansion by BaudlerArtDesign
...for the 2-part version of the mighty stand by ztander ...