27 xenz 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Laundry Rack repair by xenz
...laundry rack repair by xenz
thingiverse
a simply laundry rack repair, hope someone will find this useful.
thingiverse
free
EasyN IP Cam mount by xenz
...easyn ip cam mount by xenz
thingiverse
easyn ip camera mount
thingiverse
free
Dell P2414 monitor LED bar by xenz
...dell p2414 monitor led bar by xenz
thingiverse
this led mount is for dell p2414h and 3528 smd 12v led
thingiverse
free
Timer slider replacement by xenz
... timer on/off slider switch replacement
update -
create one with a bigger thumb slider, much easier to use than the original one.
thingiverse
free
Cable ring clip by xenz
...ay to chain up couple display adapters for conference room so they don't walk away, use this and couple zip tie does the job.
thingiverse
free
Toilet Trophy by xenz
...sent you the toilet award trophy, you deserved it !
2018 version toilet genie trophy : https://www.thingiverse.com/thing:2858167
thingiverse
free
Kitchen Sink accessories rack by xenz
... 2 sticks that's 22.5degree, added a 2nd bar with 45degree stick and a 3rd bar with 45degree then 22.5degree "hook"
thingiverse
free
5.5mm hex to drill adapter by xenz
... can tighten and loosen each clamp in record speed =p
please check dimension before print - it may not fit your drill or hex key.
thingiverse
free
MasterCraft 20V charger cover by xenz
...up and it clamp okay. good enough for me as it covered the exposed pin and it's not falling off. hope someone find it useful.
thingiverse
free
Dual mosfet mount for Melzi board by xenz
...igured they both heat up, if hotbed connect can fail, so do extruder.
grab rawlogic's standoff and remix it to hold 2 module.
thingiverse
free
Toilet Genie Trophy by xenz
...hing:2300088
proudly show your printed toilet genie with head held high by clicking on "i made one" and post the photo.
thingiverse
free
Shower mount for shower pole, caddies and shelves by xenz
...ommand strip mount by headcrabned http://www.thingiverse.com/thing:1618857 and the design is perfect for the shower handle mount.
thingiverse
free
Yet another Frankenstein style light switch by xenz
... well, so i trim the nub to 12.5mm and work good on the 2nd install. hope people find it useful.
updated #2
added 11mm switch nub
thingiverse
free
Nest Hello mount bracket with 4° tilt and extended wire cover by xenz
...e 4 degree exterior cladding tilt plus covering the wire came from the wall and re-use the existing drill hole. it does the job.
thingiverse
free
Tripod Thread Adapter for Xenz' "Webcam mount for Wanhao Di3 / Monoprice Maker Select v2.1" by AlxPx
...bcam, or having the screw section break off inside your webcam's tripod mount, please use the tested settings outlined below.
thingiverse
free
Laptop tripod stand by xenz
...ith 6.8lbs on top of the center post which is 39" long and most important 3) because i shorten 1 leg for my own requirement.
thingiverse
free
Tool holder for Wanhao Di3 / Monoprice Maker Select v2.1 by xenz
...er, nozzle drill and the extruder jam cleaning rod.
update 3/26/2017: you'll need a m3 x 10mm or longer screw to mount this.
thingiverse
free
Webcam mount for Wanhao Di3 / Monoprice Maker Select v2.1 by xenz
...installed, which raised the y axis frame off the ground. please do appropriate measure or modify in cad software before printing.
thingiverse
free
Side view mirror actuator shaft and gear replacement by xenz
...dollar.
if you have the same side view mirror actuator and need these parts, welcome to download and try see if it work for you.
thingiverse
free
LM8UU mount replacement for Monoprice MakerSelect v2.1 by xenz
...ount in my photos.
note
please pay attention to the y axis plate i have, if yours different then the screw holes may not line up.
thingiverse
free
Bed handle for Wanhao Di3 / Monoprice Maker Select v2.1 by xenz
...it. don't need tape or screws for it to work. having said that, i did put some doubleside tape to make it a bit more secure.
thingiverse
free
3mm glass corner clamps for Wanhao Di3 / Monoprice Maker Select v2.1 by xenz
...hanging glass is a breeze, one clip off, pop out, slide back in and one clip back on.
hope you fellow v2.1 owner found it useful.
thingiverse
free
Y axis cable chain horizontal mount for Wanhao Di3 / Monoprice Maker Select v2.1 by xenz
... then this mount isn't for you.
also, the rear mount do extended the printer about 8cm in length. measure before you print !!
thingiverse
free
LED light mount for Wanhao Di3 / Monoprice Maker Select v2.1 by xenz
...filament was rubbing on the z brace quite a bit. hence i created the filament feed module. well, it's there and work for me.
thingiverse
free
Y axis cable chain mount for Wanhao Di3 / Monoprice Maker Select v2.1 by xenz
... out at all. and hasn't melt yet ;)
update dec 30/2017 :
made a horizontal version https://www.thingiverse.com/thing:2737592
thingiverse
free
Screwless Tool holder for Monoprice Maker Select or Wanhao Di3 by defiantrebel
...by defiantrebel thingiverse i printed the original version from xenz but was disappointed that the factory screw wasn't long...
thingiverse
free
Y axis cable chain mount for Monoprice Maker Select v2.1 with modified carriage plate by dannytheboss9
...i wanted to print the cable protector made by xenz and sigismond0, but i had switched out my y...