27 wavexx 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Petri Dish Cap by wavexx
...cap by wavexx
thingiverse
a simple cap for a standard petri dish.
in this case it was printed in black to act as a light shield.
thingiverse
free
STM32 Nucleo F4 / F4* bumper by wavexx
...stm32 nucleo f4 / f4* bumper by wavexx
thingiverse
super-simple, minimal bumper for the st nucleo f4* boards.
thingiverse
free
Tarantula display hanging hooks by wavexx
...arantula display to a vertical surface, such as the side of a cabinet. the hooks must be glued (i used strong double-sided tape).
thingiverse
free
Cat Stand for IPhone 5 by wavexx
...r it wins on cuteness alone.
stretch on z as desired. might hold other mobiles, however getting the right fit can be challenging.
thingiverse
free
Piston Keychain (press-fit version) by wavexx
...required! i used a vice:
https://youtu.be/d8rxq-3lft8
tested with petg, 0.2 layers, 0.4 nozzle, 2 perimeters, no infill required.
thingiverse
free
GM328 Transistor-tester battery holder by wavexx
...around the pcb (<0.1mm gap). push firmly the pcb until it snaps into place. m3 screws can be directly fastened on the support.
thingiverse
free
Sausage Dipole Antenna mount by wavexx
...up. when satisfied, line the interior with silicone and close shut.
be sure to take an action shot during the first comm-check ;)
thingiverse
free
Zassenhaus coffee grinder Sliding Cap by wavexx
...ate freely, with just a little bit of friction.
petg with 0.4 nozzle, 0.2 layer height, 4 perimeters and 100% infill recommended.
thingiverse
free
Orange Scientific Comfopette screw-cap v2 by wavexx
...ue. please note the correct orientation of the teeth by looking at the images (same as provided in the model: teeth lining down).
thingiverse
free
FXF11 LED diffuser by wavexx
...e to it's milky nature, but i didn't have any at hand. if you have the chance to try, please let me know in the comments!
thingiverse
free
IFlight XL5 BN-880 GPS holder by wavexx
... support holes (these are press-fit) until the bottom faces are flush. once screwed back in place the holder/gps is fully locked.
thingiverse
free
Luer Lock M/F Cap by wavexx
...sls/sla process should result in an air-tight part.
a big shootout to this page which provided a good basis for the measurements.
thingiverse
free
ZTE MF920/MF920V cradle by wavexx
...some pins for a snap-fit, but i was lazy. the cradle and legs are printed without supports, but need to be glued together.
enjoy!
thingiverse
free
Simple CR2032/CR2016 battery tester by wavexx
... led on the negative.
fill with hot glue in order to improve stability of the battery contacts.
when cooled, glue the bottom cap.
thingiverse
free
Dual Horizontal Badge Holder (two id cards) by wavexx
...with one copy being mirrored along the x axis (as shown in the picture!), then glue both halves together to get the final holder.
thingiverse
free
Radial filament guide for cabinet mount by wavexx
...ariant) sitting on top of the cabinet, combined with these hooks https://www.thingiverse.com/thing:2923602 for the display panel.
thingiverse
free
Bowden tube support clamp for Tevo Tarantula by wavexx
... smoothly)
5) push firmly (holding the carriage) until it clicks in place
6) reconnect tube, reinsert filament
7) resume printing
thingiverse
free
Tarantula adjustable front facing Z limit switch by wavexx
...ing adjustment enough: given how often the bed needs to be re-leveled, this is easily the best mod i did on the tarantula so far.
thingiverse
free
Soldering Helping Hands Remixed³ by wavexx
...9;s too hard, remove one loop from the elastic. if it's too soft, add a loop instead. remove the packing wire when satisfied.
thingiverse
free
MK3 screw-on reverse bowden by wavexx
...ire 0.15mm layer height, 0.4 nozzle.
using other settings might compromise the tightness of the screw and fit of the bowden tube.
thingiverse
free
Worms figure by LesDeuxDuFond
...from worms 3d. edit : improved version here, by wavexx ...
thingiverse
free
Prusa MK3/MK3S Y bearing housing by wavexx
...ngth, improving y axis homing accuracy. i've been using these on several mk3 printers with careful adjustment without issues.
thingiverse
free
3TSS: 30mm Tube Spool System by wavexx
... it can be scaled down, but not up, since the border of the tube needs to be perfectly flush in order to let the components pass.
thingiverse
free
Component Tester Box by wimberleytech
...(yet another component tester box). i was inspired by wavexx who posted one recently. my tester is different than...
thingiverse
free
Soldering Helping Hands Basic Base by things4j
...required files please refer to: https://www.thingiverse.com/thing:4029106 (all credits to wavexx ...
thingiverse
free
5KG spool holder by bchiaino
...on my page for some reason, all credit goes tohttps://www.thingiverse.com/wavexx ijust made the wheels and railswider for bigger rolls...
thingiverse
free
Wider Slider Sign by uncleflip
...uncleflip thingiverse the universal door sliding sign (https://www.thingiverse.com/thing:4374913) from wavexx was perfect for my needs.......almost. i decided to make...