25 tymm 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
STM32 Nucleo coaster by tymm
...stm32 nucleo coaster by tymm
thingiverse
coaster for mounting stm32 nucleo development boards.
thingiverse
free
Basic Box for Electronics, etc. by tymm
...basic box for electronics, etc. by tymm
thingiverse
just a basic printable box.
thingiverse
free
Fittings for 0.5 inch conduit by tymm
...fittings for 0.5 inch conduit by tymm
thingiverse
these are assorted fittings for use with electrical conduit.
thingiverse
free
Solder Spool Spacers by tymm
...tymm
thingiverse
spacer made for solder spool holders, to help keep solder from getting caught between the spool and the holder.
thingiverse
free
Arduino Nano Terminal Adapter Plate by tymm
...dapter plate by tymm
thingiverse
plate for mounting the arduino nano terminal adapter boards that can be found around the ebays.
thingiverse
free
NEMA17 Motor Bearing Offset by tymm
...od. it's made to fit over a coupler with screwdriver access to the set screws, and gives space for a 625 bearing at the top.
thingiverse
free
NEMA17 adapter for Canon CN38 servo motor by tymm
...
adapter to allow canon cn38 servo motors (which at one point were insanely cheap on ebay) to be attached to nema17 motor mounts.
thingiverse
free
STM32F0 Discovery Board Box by tymm
...sistent printing.
this could probably use a little more tweaking around where the clasps grab, but has worked pretty well for me.
thingiverse
free
Fluke 97 Scopemeter Stand Mount by tymm
...sintegrating over the past few years.
far from perfect, but to the point that i'm done fiddling with it (at least for now).
thingiverse
free
Bracket for Ubiquiti wifi POE power adapters (24v version) by tymm
...ymm
thingiverse
this is a small little bracket for mounting passive 24v poe power adapters that ship with ubiquiti wifi routers.
thingiverse
free
Plug for Mounting Desk Lamp in Ergotron LX post by tymm
... (the type with a post that gets stuck in a clamp) to be mounted on top.
please check diameter of your lamp post before printing.
thingiverse
free
Spacer for older metal Akro-Mils storage drawers by tymm
...sed set with only a few spacers, and needed tons more.
from my experience, this will not fit their newer clear plastic drawers.
thingiverse
free
Enclosure for OpenVizsla USB Sniffer by tymm
...blems in pla. made to use 4 x ~3mm self-tapping screws -- the ones i'm using came from flotsam in a random drawer, so ymmv.
thingiverse
free
Tektronix TM500 module parts by tymm
...i wanted to deal with side panels.
these should at least be a good start for anyone wanting to pick up where i left off, however.
thingiverse
free
Printed Motor Mount for Sherline Machines by tymm
...mounting screws, of course).
tested so far for fit (with bearings), but will be a bit yet before i'm able to test function.
thingiverse
free
Replacement switch lever for Metcal MX500 by tymm
...; sandpaper for smooth operation (as you can see from print in gallery, filament feed also wasn't calibrated for this print).
thingiverse
free
Desk Mount for 65W Macbook Power Supply by tymm
...rapped around to take up slack.
note: i'm not sure if dimensions match current power supplies; please verify before printing.
thingiverse
free
Reflective RPM sensor mount for Taig mill by tymm
...ve not tested at speed on a running mill (and due to other obligations am unlikely to have a chance to do so in the near future).
thingiverse
free
(unfinished) Replacement Keypad for Racal Dana 2101 Counter by tymm
...mmunicate which key is which.
when completed, it would likely also be possible to adapt for other racal dana counters (e.g. 1998)
thingiverse
free
Steadyrest for Sherline Lathe (WIP) by tymm
...ent in any direction by pushing on the top by hand... but should work fine for light work.
2014-04-06 - v0.4; getting closer :)
thingiverse
free
Y Limit Switch Brackets for Taig Mill by tymm
...1 switches)
2 - 10-24 x 7/16 screws (or 10-24 x 1/2 and 1 or 2 10-24 washers)
2 - 10-24 nuts
2 - 2-56 x 7/16 screws
2 - 2-56 nuts
thingiverse
free
Plate for DIY opto interface for DE5000 handheld LCR meter by tymm
...the interface; it shouldn't require much more than a usb-ttl rs232 adapter, an ir led, ir photodiode and a comparator though.
thingiverse
free
Replacement access latch handle for Delta 8 inch bandsaw by tymm
...r the pin with a 3mm drill bit. mine still needed a bit of help with a hammer on a hard surface to get the pin mounted properly.
thingiverse
free
Quick little vacuum former nozzle for mini shop vacuum by tymm
...ed / photodiode sensors.
note that there is assorted support material as part of the design that will need to be removed for use.
thingiverse
free
Parametric lower Z (motor) mounts for AO / MendelMax printers by tymm
...ut in effort to get things right. if you have issues or suggestions, let me know and i'm happy to try and get things sorted.