29 tonyno 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Shamrock Bottle Topper by tonyno
...shamrock bottle topper by tonyno
thingiverse
obvious combo!
thingiverse
free
Parts Tray by tonyno
...parts tray by tonyno
thingiverse
as big as it was, why not just go all the way with the print? :d
thingiverse
free
Eave Pixel Clip by tonyno
...eave pixel clip by tonyno
thingiverse
remixed for aluminum soffit/fascia with a trim-width of 1". updated.
thingiverse
free
Dig-Uno Enclosure by tonyno
...dig-uno enclosure by tonyno
thingiverse
snap-together enclosure for quinled dig-uno with provision for wi-fi antenna.
thingiverse
free
Car Sunglasses Hook by tonyno
...lasses hook by tonyno
thingiverse
a hook for sunglasses meant to push into an overhead panel gap. print the j-piece on its side.
thingiverse
free
Chromecast Remote Extender by tonyno
...ote extender by tonyno
thingiverse
the chromecast remote is a bit small for my hands, so i created this to make it a bit longer.
thingiverse
free
StrongDoorOpener.2 by tonyno
...finally snapped after about two weeks, so this one has a 4mm wall. i also added a bar that keeps it from rotating on your finger.
thingiverse
free
Mask Clip Part Deux by tonyno
...ip part deux by tonyno
thingiverse
a new clip for https://www.thingiverse.com/thing:4623214 i added arms to help open the clasp.
thingiverse
free
XYZPrinting DaVinci 1.0 Inside Hole Cap by tonyno
...xyzprinting davinci 1.0 inside hole cap by tonyno
thingiverse
thickened up the top and added a taper.
thingiverse
free
Dig-Uno Enclosure by tonyno
...led dig-uno with provision for wi-fi antenna.
update: made antenna hole a bit bigger as well as thickened locking tabs on bottom.
thingiverse
free
Path Light Stake by tonyno
... are alignment holes that you can put filament through to keep halves aligned while gluing. holes likely need to be reamed a bit.
thingiverse
free
Yet Another Toilet Paper Extender by tonyno
...tender by tonyno
thingiverse
this is v4 of my roll extender. added a partial flange to keep the roll from jumping over the arms.
thingiverse
free
Scotch Brite Dish Brush Foot by tonyno
...o
thingiverse
remixed (from scratch) for the scotch brite dish brush which has more of an overhang so it requires a bigger base.
thingiverse
free
Tape Dispenser by tonyno
...'t work with poly tape.
just added a 25 and 50mm version by request. may need to be strengthened. let me know if you make it.
thingiverse
free
Yet Another Tablet Wall-Mount Bracket by tonyno
...ed for an older, lenovo (s2109a-f) android tablet, but should work on many others. i use three. two on the bottom and one on top.
thingiverse
free
Workclamp 65mm x 20mm Remix by tonyno
...rt c face down for no supports (there are bridges instead). you will need to punch through a one-layer membrane for the m5's.
thingiverse
free
Earphone Wrap Case by tonyno
...d the body. i've also found that the hole size is perfect for tucking the earbuds into for keeping them from flopping around.
thingiverse
free
Yet Another Shower Head Holder by tonyno
....82" od pipe) using an m5x40 hex-head screw, flat washer, and nut.
print "upside down" for least required support.
thingiverse
free
SimpleHuman Wall Mount Pump Hanger by tonyno
...sized for a towel rack with a 3/4" square bar and a #8 x 3/8" screw. if you have the dual or triple version, print two.
thingiverse
free
Samsung S21 Ultra Charging Mount by tonyno
..., #4 x 3/8 screws. i used a couple, small dabs of epoxy to hold the usb connector in place.
not for bare phone, but with a case.
thingiverse
free
Helping-Hands Clamp by tonyno
...ill/strength, added ribs for better grip.
update 3: apply a little bit of silicone (caulk) to the grip surfaces. a great upgrade!
thingiverse
free
Toggle-Clamp Mount for Misumi Extrusion Bed by tonyno
... screws and nuts. clamp can be mounted either parallel, or perpendicular to t.
v2 has been adjusted for a better fit (less slop).
thingiverse
free
Corner Connector - 3-Way by tonyno
..., but these fit tightly coming off of my printer.
no support required if you rotate so that it stands on a corner point as shown.
thingiverse
free
DaVinci Filament Resetter (No Battery) by tonyno
...pins and eliminated end board-clip.
original pogo pinshttps://www.amazon.com/uxcell-spherical-tipped-spring-testing/dp/b007q847i0
thingiverse
free
Oblong Tablet Nest for Safety Shield Pill Splitter/Cutter by tonyno
...t sure if it's needed, but version 2 is rotated to lie flat if your slicer can't place a model flat on the build surface.
thingiverse
free
Bumper Clips for Roomba 800-Series by tonyno
...s by my cabinets to the point of not doing their job. i've fallen back to just extending the 360° ir turret about 3mm taller.
thingiverse
free
Arduino Nano DaVinci 1.0 Filament Cartridge Resetter 2 by tonyno
... board in. bonus: it's smaller.
original pogo pinshttps://www.amazon.com/uxcell-spherical-tipped-spring-testing/dp/b007q847i0
thingiverse
free
DaVinci 1.0A Wire-Brush Holder by tonyno
...ded some holes so that you can use a small screw to hold the brush in if it's not tight enough, or if you cut it a bit short.
thingiverse
free
Samsung Note 5 w/Soft Case Holder & Wireless Charger-AMPs Mount by tonyno
...0size%201%22%20(holds%20up%20to%205%20lbs)&facets[hole_pattern][]=amps%204-hole%20pattern&facets[part_type][]=base#wizard