20 technoswiss 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Hanger Holder by TechnoSwiss
...hanger holder by technoswiss
thingiverse
hook to hold hangers parallel to hanger rod.
thingiverse
free
Printrbot Glass Clips by TechnoSwiss
...printrbot glass clips by technoswiss
thingiverse
clips for holding a glass sheet on the printrbot.
thingiverse
free
SainSmart A20A Case by TechnoSwiss
...hnoswiss
thingiverse
this is a case i created for the sainsmart bt to serial port module.
this was printed on a tiko in gem pla
thingiverse
free
eeePC Stand by TechnoSwiss
...s. a hole is included for a 3/16" dowel to hold the supports together. the hole can be reamed out to 5mm for a metric dowel.
thingiverse
free
Dungeon! Board Game Card Holder by TechnoSwiss
...! board game card holder by technoswiss
thingiverse
this is a set of card holders for the game dungeon!, the d&d board game.
thingiverse
free
Rod Support for Spool Hanger by TechnoSwiss
... technoswiss
thingiverse
this is a plug for a 1" pvc spool hanger so a 5/8" dowel can be used with the filament spool.
thingiverse
free
Calibration Block with Countersunk Hole and Slot by TechnoSwiss
...noswiss
thingiverse
calibration block with countersunk hole and slot to catch problems with elements inside perimeter of object.
thingiverse
free
Spool Holder by TechnoSwiss
... the bin i was pulling them from at the hardware store. i think their bin is mis-labeled, as i get 5/8" when i measure them.
thingiverse
free
75mm VESA Apple TV Bracket by TechnoSwiss
...esa bracket for mounting to to the back of a tv. includes a place to wind up the cord, and a shelf for holding an hd ota antenna.
thingiverse
free
Printrbot Plus 2.0 Optical Z-endstop Mount by TechnoSwiss
...
bracket for mounting an optical z-endstop on the printrbot plus v2.0 using the mounting holes for the mechanical switch endstop.
thingiverse
free
Printrbot PCB Heatbed Standoff by TechnoSwiss
...es. this support goes under the heatbed to limit the compression.
see photo...
ymmv based on the thicknessof your insulation.
thingiverse
free
Fan Mount for Dial Indicator by TechnoSwiss
...e from measuring all the way to the back of the bed. you're results may vary. dial indication is simply press-fit into mount.
thingiverse
free
Fan Duct for Printrbot+ 2.x by TechnoSwiss
...ing too much of the parts i was printing at a go so i put this duct together to help focus it on just the portion being extruded.
thingiverse
free
12-Port Patch Panel Bracket by TechnoSwiss
...d one of the bracket middle. they should all join together. i use a fender washer with these to mount them to a sheet of plywood.
thingiverse
free
Servo Light Switch Flipper by TechnoSwiss
...ideo of it in action is https://youtu.be/42pdmewwjh0
raspberry pi script is https://github.com/technoswiss/rpi-light-switch-servo
thingiverse
free
LM8UU Linear Bearing Puller by TechnoSwiss
...ger bolt if you can't push the new bearing in part way by hand.
printed at 0.21mm layer higher and 40% infill with esun pla.
thingiverse
free
Printrbot JR 1307 Fan Mount with Shroud by hashtagdavi
...fan to mount onto the extruder. you can view technoswiss original submission by viewing the "remixed with" section on...
thingiverse
free
Monoprice Network Bracket for Leviton Structured Media
...monoprice network bracket for leviton structured media thingiverse technoswiss made a good bracket that fits my 12 port...
thingiverse
free
Ender 3 lower filament guide for 604 bearing by ahecht
...a remix. the original design was made by holspeed, technoswiss#39;s remix changed it to use a 604uu bearing (the...
thingiverse
free
ender 3 filament guide 604 bearing dual gear extruder by Rangerholt
...original design is from holspeed. which was remixed by technoswiss to use a 604uu bearing (the one that comes...